ford freestar cruise control deactivation


You are searching repair manual in PDF format about ford freestar cruise control deactivation use another keyword for search another post or files



  ford freestar cruise control deactivation Direct Download speed 5787 Kb/s

  ford freestar cruise control deactivation Full Version speed 6767 Kb/s




1995 Jeep Grand Cherokee Limited CRUISE CONTROL SYSTEM Service & Repair

0

Filed Under (Jeep) by admin on 22-04-2010

download

If vehicle is equipped with air bag, air bag must be deactivated before servicing cruise control components on or around steering column. See appropriate AIR BAG RESTRAINT SYSTEM article in ACCESSORIES & EQUIPMENT. NO CRUISE CONTROL WHEN SET BUTTON IS PRESSED & RELEASED Check for: blown fuse, no vacuum at servo and/or defective servo, disconnected speed control cable, brakelight switch out of adjustment, faulty electrical circuit, faulty Park/Neutral switch input to PCM, faulty PCM. CRUISE CONTROL ENGAGES WITHOUT ACTUATING CRUISE SET BUTTON Check for: defective servo, faulty electrical circuit or control switch. CRUISE CONTROL ENGAGES WHEN ENGINE IS STARTED Check for: defective servo, faulty electrical circuit. ERRATIC SPEED OR ENGINE SHUTS OFF Check for: poor engine performance (surge), defective vehicle speed sensor, vacuum leak, faulty servo, faulty
CRUISE CONTROL DISENGAGES ON ROUGH ROAD Check for: brakelight switch out of adjustment, faulty cruise control switch, faulty electrical circuit. ENGINE DOES NOT RETURN TO NORMAL IDLE Check for: kinked and/or damaged cruise control cable, faulty throttle linkage.

Related entry:

fuse for cruze control 2009 pontiac g5, remove cruise controlto 1992 ford 460 engine, 2002 jeep liberty hvac heater hose assembly, fuse number for cruise control on 03 grand marquis, how to change cruise control module on 2008 impala, how to repair or replace a cruise deactivator switch, how to replace a servo deactivation switch, montero limited auto cruise schematic diagram, replacing cruise control on a 2004 Lexus RX330, fuse location for cruise control for 03 grand marquis,

1992 Chevrolet Suburban C2500 Cruise Control Electric Servo DESCRIPTION & OPERATION

0

Filed Under (Chevrolet) by admin on 18-06-2010

download
DESCRIPTION Cruise control system components include cruise control module (control module and electric stepper motor servo combined), cruise control switch, vehicle speed sensor, and brake and clutch release switches. A vehicle speed sensor buffer is used on 1991 Motorhome and 1992 vehicles. CRUISE CONTROL MODULE Cruise control module is mounted on upper radiator support, to left of radiator (Motorhome), or next to master cylinder (all others). See Fig. 1 . Module incorporates an electronic control module and an electric stepper motor servo. Servo regulates throttle position in response to control module commands. Module is not serviceable.

Related entry:

2000 crv cruise control repair, cruise control module 2000 CRV location, how to replace 2-4 band servo on 04 silverado and location, howtoreplaceasmartcruisemodule, location 2000 crv cruise control release switch, remove ac servo motor 1998 camry,

Ford / Mercury / Lincoln Band-Mounted Sensor Re-Learn Instructions

0

Filed Under (Ford, Lincoln) by admin on 17-10-2009

The instructions below can be used for the following vehicles: 2008 Ford Crown Victoria / Lincoln Town Car / Mercury Grand Marquis 2008 Ford E-series 2007-2009 Ford Edge / Lincoln MKX 2005-2008 Ford Escape / Mercury Mariner 2007-2009 Ford Expedition / Lincoln Navigator 2006-2009 Ford Explorer / Lincoln Aviator / Mercury Mountaineer 2007-2008 Ford F150, F250, and F350 / Lincoln Mark LT
2009 Ford Flex 2008-2009 Ford Focus 2006-2007 Ford Freestar / Mercury Monterey 2008-2009 Ford Fusion / Lincoln MKZ / Mercury Milan 2007-2009 Ford Mustang 2007-2009 Ford Ranger 2008-2009 Ford Taurus / Mercury Sable

1. Make sure all tires are inflated to the vehicle’s recommended inflation pressures (found in the owner’s manual on the door placard). 2. Turn the ignition switch to OFF then press and release the brake pedal. 3. Turn the ignition switch from OFF to RUN (engine OFF) 3 times, ending in the RUN position. Do this within 10 seconds. 4. Press and release the brake pedal

download

Related entry:

burping the cooling system ford f150 4 6l, 1990 ford ran 2 3 distributless eng ignitionspark diagram, 2002 ford taurus iac relearn, ford lynx service manual, 1997 ford f150 owners manual fuse diagram, schéma électrique airbag ford focus, ford freda 2000 model auto manuals, 2004 ford freestar power steering turns tight then free tight then free what is the problem, ford focus tcm 2008, recharging ac on 2002 thunderbird,

1999 Ford Expedition Climate Control System DIAGNOSIS AND TESTING

0

Filed Under (Ford) by admin on 28-03-2011

download
Inspection and Verification 1. Verify the customer’s concern by operating the climate control system to duplicate the condition. 2. Inspect to determine if one of the following mechanical or electrical concerns apply: Visual Inspection Chart Loose, missing or damaged A/C compressor drive belt. Loose or disconnected A/C clutch. Loose, misrouted or damaged vacuum lines. Broken or leaking vacuum control motora Discharged A/C system. Broken or leaking refrigerant lines. a a A leak in the vacuum control circuit may occur during acceleration (slow leak), may exist at all times (large leak), and may exist only when specific functions are selected (indicating a leak in that portion of the circuit). The vacuum hoses used in the passenger compartment control circuit are constructed from PVC plastic material. The vacuum hoses used in the engine compartment are constructed of Hytrel®. Because of the materials used, never pinch the vacuum hoses off during diagnosis to locate a leak. A wood golf tee can be used as a plug when it is necessary to plug one end of the vacuum hose for leak test purposes. 3. If the inspection reveals obvious concern(s) that can be readily identified, service as required. 4. If equipped with the electronic automatic temperature control system, go to Step 6. 5. If equipped with a manual A/C system, determine the symptom and go to the Symptom Chart. 6. If the concern remains after the inspection, connect the Rotunda New Generation Star (NGS) Tester to the data link connector (DLC) located beneath the instrument panel to carry out the DATA LINK DIAGNOSTICS test. If the NGS responds with NO RESPONSE/NOT EQUIPPED for the electronic automatic temperature control module, GO to Pinpoint Test A. If the DATA LINK DIAGNOSTICS test is passed for the electronic automatic temperature control module, retrieve the continuous DTCs and execute the Self-Test Diagnostics for the electronic automatic temperature control module to retrieve the current DTCs. Mechanical Electrical Open fuses. Blower motor inoperative. A/C compressor inoperative. Circuitry open/shorted. Disconnected electrical connectors. 7. If the self-test is passed and no DTCs are retrieved, go to the Symptom Chart to continue diagnostics. 8. If DTCs are retrieved, go to the Electronic Automatic Temperature Control (EATC) Module Diagnostic Trouble Code (DTC) Index to continue diagnostics. 9. If the electronic automatic temperature control module cannot be accessed by the NGS, GO to Pinpoint Test A. Electronic Automatic Temperature Control Module Self-Test The EATC module self-test will not detect concerns associated with data link messages like engine coolant temperature or vehicle speed signals. A NGS tester must be used to retrieve these concerns. The EATC module self-test will detect concerns in the system control functions and will display hard diagnostic trouble codes (DTCs) in addition to intermittent diagnostic trouble codes for concerns that occur during system operation. The vehicle interior temperature should be between 4-32° (40-90°F) when performing the self-test. If the temperatures are C not within the specified ranges, false in-car temperature sensor DTCs will be displayed. The self-test can be initiated at any time. Normal operation of the system stops when the self-test is activated. To enter the self-test, press the OFF and FLOOR buttons simultaneously and then press the AUTOMATIC button within two seconds. The display will show a pulse tracer going around the center of the display window. The test may run as long as 30 seconds. Record all DTCs displayed. If any DTCs appear during the self-test, follow the diagnostics procedure given under ACTION for each DTC given. If a condition exists but no DTCs appear during the self-test, refer to the Symptom Chart Condition: The EATC System Is Inoperative, Intermittent or Improper Operation. To exit self-test and retain all intermittent DTCs, push the blue (cooler temperature) button. The control will exit self-test, retain all intermittent DTCs and then turn OFF (display blank). To exit self-test and clear all DTCs, press the DEFROST button. The vacuum fluorescent display window will show 888 and all function symbols for one second. Then, the EATC control assembly will turn OFF (display blank) and all DTCs will be cleared. Always exit the self-test before powering the system down (system turned OFF). Intermittent DTCs will be deleted after 80 ignition switch ON cycles after the intermittent condition occurs.

Related entry:

2006 hyundai sonata temerature actuator, eatc diagnostics 2002 ford, 2002 buick lesabre electronic level control, 500 w140 climate control diagnosis, where is the temperature control module located on a 1998 lincoln navigator, 99 grand marquis climate control self test, 2006 lincoln towncar ac test shows pinpoint test e, reset climate control gmc envoy, audi climate control stuck in auto, 2006 acura tl climate control self diagnostics feature,

2000 Toyota Corolla CE Heating and Air Conditioning Control Assembly Removal and Installation

0

Filed Under (Toyota) by admin on 06-05-2011

download
12. REMOVE A/C CONTROL ASSEMBLY Remove the 2 screws and pull out the A/C control assembly, then disconnect the connector. NOTE: Be careful not to vent the mode control cable, when pull out the A/C control assembly. INSTALLATION 1. INSTALL A/C CONTROL ASSEMBLY a. Connect the connector. b. Pass the heater control cables as shown in the illustration. COMPONENTS REMOVAL 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. REMOVE COWL SIDE TRIMS REMOVE FRONT DOOR SCUFF PLATES REMOVE LOWER FINISH PANEL REMOVE LOWER INSERT PANEL REMOVE CENTER CLUSTER FINISH PANEL REMOVE HEATER TO RESISTOR NO.2 DUCT REMOVE LOWER PANEL REMOVE REAR CONSOLE BOX REMOVE SHIFTING HOLE BEZEL REMOVE FINISH LOWER CENTER PANEL 11. DISCONNECT HEATER CONTROL CABLE c. Install the 2 set screws. 2. CONNECT HEATER CONTROL CABLES a. Set Air inlet control lever at “RECIRC” position b. Set Temperature control dial at “MAX. COOL” position c. Set Mode control dial at “DEF” position Zoom d. Adjust air inlet control cable. Set air inlet damper control lever to “RECIRC” position and connect the inner cable to lever pin and clamp the outer cable. HINT: Lock the clamp while lightly pushing the outer cable to the direction shown by arrow in the illustration. Sized for Print Zoom e. Adjust air mix control cable. Set air mix damper control lever to “MAX. COOL” position and connect the inner cable to lever pin and clamp the outer cable. HINT: Lock the clamp while lightly pulling the outer cable to the direction shown by arrow in the illustration. Sized for Print

Related entry:

how to fix heater controls on toyota yaris, 1967 chevelle heater control cables install, 1993 dodge dakota heater control cable, 2009 toyota corolla air mix control damper, location of heat temperature section on toyota yaris 2012, pinout air conditioner pajero 2009, toyota corolla a/c mode cable remove and replace, toyota corolla a/c mode cable remove and replace 2009,