ford ka diagnostic code 412


You are searching repair manual in PDF format about ford ka diagnostic code 412 use another keyword for search another post or files



  ford ka diagnostic code 412 Direct Download speed 5787 Kb/s

  ford ka diagnostic code 412 Full Version speed 6767 Kb/s




VW MKIII Golf / Jetta Technical Bulletin Diagnostic Trouble Code (DTC)

0

Filed Under (volkswagen) by admin on 30-03-2010

download
Diagnostic Trouble Code (DTC) Memory, displaying blink codes Starting with 8.94 production (1995 m.y.), Golf///,
Jetta/// and Cabrio vehicles are equipped with a special OBD1 adapter for use with the On Board Diagnostic (OBD) system. The adapter is used to check Diagnostic Trouble Code (DTC) Memory when the VAG 1551 Scan Tool
(ST) is not available. Stored malfunctions are displayed as blink codes by the Malfunction Indicator Lamp (MIL) in the vehicle.
play is activated by using the adapter in conjunction with the vehicle’s Data Link Connector (DLC). The adapter makes connection between connector sockets 15 (L-wire) and 4 (Battery Ground)

Related entry:

2000 lincoln town car 4 6 code u1039, instructions to run Ford diagnostic test EATC, body controller-system diagnostic code 3 special instruction, 2007 pt cruiser has no spark p0335 p0340, maxxforce dt trouble codes, 2001 sephia troubleshoot codes, how to diagnostic p2716 code, ford explorer brake pedal diagnostic chart, fixing code c1226, diagnostic codes for 1995 cadillac eldorado,

Ford / Mercury / Lincoln Band-Mounted Sensor Re-Learn Instructions

0

Filed Under (Ford, Lincoln) by admin on 17-10-2009

The instructions below can be used for the following vehicles: 2008 Ford Crown Victoria / Lincoln Town Car / Mercury Grand Marquis 2008 Ford E-series 2007-2009 Ford Edge / Lincoln MKX 2005-2008 Ford Escape / Mercury Mariner 2007-2009 Ford Expedition / Lincoln Navigator 2006-2009 Ford Explorer / Lincoln Aviator / Mercury Mountaineer 2007-2008 Ford F150, F250, and F350 / Lincoln Mark LT
2009 Ford Flex 2008-2009 Ford Focus 2006-2007 Ford Freestar / Mercury Monterey 2008-2009 Ford Fusion / Lincoln MKZ / Mercury Milan 2007-2009 Ford Mustang 2007-2009 Ford Ranger 2008-2009 Ford Taurus / Mercury Sable

1. Make sure all tires are inflated to the vehicle’s recommended inflation pressures (found in the owner’s manual on the door placard). 2. Turn the ignition switch to OFF then press and release the brake pedal. 3. Turn the ignition switch from OFF to RUN (engine OFF) 3 times, ending in the RUN position. Do this within 10 seconds. 4. Press and release the brake pedal

download

Related entry:

1997 Lincoln Repair Manual Free, front end ailgment on a murcury mountaineer awd 2000, yhs-mystartdefault, ford ecp, Ford Laser Kj2 Workshop Manual, ford ranger lub chart, indicators for 2006 ford 500, ford sapphire v6 service manuel, Ford Courier Gearbox Diagram, 2009 fusion axel nut torque,

2005 Ford Expedition, Ford F-250, Ford F-350 TICKING AND/OR KNOCKING NOISE FROM ENGINE

0

Filed Under (Ford) by admin on 07-09-2010

download
FORD: 2005 Mustang 2004-2005 F-150 2005 Expedition, F-250, F-350 This article supersedes TSB 05-15-8 to update the Service Procedure. ISSUE Some vehicles equipped with a 4.6L 3-valve or 5.4L 3-valve engine may exhibit a ticking and/or knocking noise after reaching normal operating temperature. The noise may be described as “ticks”, “taps”, “knocks”, or “thumps”. In some cases the noise may be a normal characteristic of these engines. In other cases the noise may require further investigation. Sorting out and defining the noise as reported by the customer is important to successfully diagnose and/or repair the condition. ACTION Before starting diagnosis, it is critical to determine the specific engine noise the customer is concerned with. The customer should be interviewed to get their detailed perception and description of the noise, and to determine if the noise occurs at idle or above idle speed, and if the engine is cold, hot, or both. Attempt to duplicate the noise, and determine the source of the symptom. Refer to the following Service Procedure to help determine the source of the noise and if a repair is needed. LINCOLN: 2005 Navigator PRE-CHECKS 1. 2. 3.

Related entry:

toyota 3400 24v ticking noise, diagram of the sunroof on a 2002 lincoln navigator, 2003 ford expedition front end diagram, 2004 f 250 front end diagram, 2011 Ford Escape Engine Noise, diagram of an evap system on a 2002 f150 4 2, fuse link for 2004 ford expedition, ford v10 knocking noise, how to instal a fender on a 2003 ford expedtion, how to clean a f350 evaporator,

1995 Ford Thunderbird Antilock Brakes / Traction Control Systems: Testing and Inspection Displaying and Reading Trouble Codes

0

Filed Under (Ford) by admin on 14-08-2010

download
NOTE: Ford DOES NOT provide procedures to retrieve or clear trouble codes without the Super Star II tester. The anti-lock brake/traction assist system has on-board diagnostic capabilities. However, the module as received from manufacturing is equipped with a stored error code (61). This will affect the service procedure. The error codes can be retrieved from the ABS module in the following manner. 1. 2. 3. 4. Connect Super STAR II tester to connector located in engine compartment on the power distribution box. Turn on Super STAR II tester and latch button down in TEST position. Turn ignition switch to RUN position. Read first code output. After approximately 15 seconds, the next code will be output. Leave button latched until all codes are output. NOTE: Make sure that all codes are written down. 5. The diagnostic procedure should be as follows provided that the CHECK ANTI-LOCK BRAKE indicator stays on all the time or flashes intermittently. NOTE: If the BRAKE warning indicator is on or intermittently comes on, refer to the Warning Indicator Symptom Chart. NOTE: If there are more codes stored in the anti-lock brake control module memory, no codes will erase until all codes have been output by the Super STAR II tester, all malfunctions have been serviced and the vehicle is driven about 40 km/h (25 mph). This means that if a 20s code originally existed and was serviced, it can be ignored when running the on-board diagnostic the second time. If the first code received is 18, 19 or in the 20s and no other code is received, service the indicated component. No other codes can be output if a 20s code exists. After servicing the indicated 18, 19, or 20s code, repeat the procedure for retrieving error codes. 6. If a code 61 is received with any other code, ignore the code 61 and service the other indicated components. If, after correcting all other indicated malfunctions, the CHECK ANTI-LOCK BRAKE indicator is still on, service the Fluid Level Switch (FLS) circuit. 7. If a code 61 is received and no other codes are received, service the FLS circuit. 8. If no code, or only a code 10 is received, use the Anti-Lock Quick Check Sheet since some possibilities are not recognized and retained in the anti-lock brake control module memory. See: Trouble Code Descriptions/Quick Check Sheet 9. When dealing with intermittent ABS warning light ON concern, make certain to visually inspect all wiring related to the component associated with the code received.

Related entry:

International Trouble Code Chart, 2005 trail blazer code p2440, Navistar Fault Code List, spn 3981 fmi 2, international workstar diagnostic code ollo2, p2293 vauxhall, INTERNATIONAL MAX FORCE flash code 4576, b1866 srs code, MAZDA PROTÉGÉ 1995-1998 ON-BOARD DIAGNOSTIC ENGINE CONTROL SYSTEM, 2010 Impala P2122,

2002 Jaguar X-Type DTC Summaries

0

Filed Under (Jaguar) by admin on 28-11-2010

download
Powertrain DTC Summaries – OBD II FAULT DESCRIPTION MONITORING CONDITIONS CHECK ENGINE MIL (CK ENG) DEFAULT ACTION POSSIBLE CAUSES DTC Diagnostic Trouble Code. SYS The powertrain system with which the DTC is associated – EMS, TRANS, ABS/TC (DSC). DTC retrieval tools: OBD II – indicates that the DTC is an OBD II code and can be accessed via a generic scan tool or WDS. JAG – indicates that the DTC is not an OBD II code and is accessed only via WDS. Fault description. “DIAGNOSTIC MONITOR DRIVE CYCLE” for the particular DTC. Operate the vehicle as described to check for a reoccurrence of the DTC. Refer to pages 4 – 7. Use WDS Datalogger or Scan Tool to monitor specified engine parameter(s). 1 2 N OTHER Driver Warnings: N None R RED MIL / Message or Powertrain Warning Indicator A AMBER MIL / Message or Powertrain Warning Indicator C Charge indicator Control Module default action: Logged – DTC stored in ECM memory buffer; Flagged – DTC stored in ECM memory / CHECK ENGINE MIL activated. CM PIN ECM (SYS – EMS) / TCM (SYS – TRANS) Connector pin number(s) Possible causes are listed in the order of diagnostic checking. HIGH VOLTAGE – High voltage can be either sensor supply voltage (5 volts) or B+ voltage. 1 TRIP – indicates that the CHECK ENGINE MIL is activated by a fault occurring during ONE “TRIP”. 2 TRIPS – indicates that the CHECK ENGINE MIL is activated by a fault occurring during TWO CONSECUTIVE “TRIPS”. NO – indicates that the CHECK ENGINE MIL is not activated. OBD SYSTEM READINESS – ENGINE MANAGEMENT If DTC P1000 is flagged after DTCs have been cleared, all engine management OBD diagnostic monitor drive cycles HAVE NOT BEEN COMPLETED. If DTC P1111 is flagged after DTCs have been cleared, all engine management OBD diagnostic monitor drive cycles HAVE BEEN COMPLETED. OBD SYSTEM READINESS – TRANSMISSION Use WDS Datalogger “TOTAL NUMBER OF DTC SET” to determine if transmission OBD monitoring has been completed. Refer to page 7. OBD DIAGNOSTIC MONITORS The Engine Management and Transmission Control systems are continuously checked during vehicle operation by the Engine Control Module (ECM) and Transmission Control Module (TCM) on-board diagnostic (OBD) facilities. Powertrain OBD incorporates six diagnostic monitors. Each monitor has an associated group of DTCs. The diagnostic monitors will complete the diagnostic test(s) if a specified service “drive cycle” is carried out. The six diagnostic monitors are as follows: – – – – – – Heated Oxygen Sensors Monitor Adaptive Fuel Monitor Misfire Monitor Catalyst Efficiency Monitor Evaporative System Monitor Comprehensive Component Monitor (Engine Management / Transmission)

Related entry:

défaut code po101 mitsubishi canter, u1900 obd2 code causes, powertrain diagnostics procedures manual Chrysler, 2005 lincoln how to scan for dtc, how to clear code p0171 from a 2005 chevy impala 3 8l v6, how to read codes on a 2005 tacomawithout scan tool, no powertrain dtc or freeze frame chrysler 300 2005, obd 1 5 1995 pontiac sunfire, powertrain diagnosis manual download 03 pt cruiser, geo metro code p0303,