download
Battery – Battery + Door function control module, driver Door function control module, passenger Door mirror adjustment motor, driver Door mirror adjustment motor, passenger Door mirror adjustment switch Earth point location 10 Earth point location 4 Earth point location 5 Earth point location 9 Electric window motor, driver Electric window motor, passenger Electric window switch, driver’s door Electric window switch, passenger door Fuse Fuse box/relay plate, engine bay Fuse box/relay plate, fascia 1 Ignition main circuits relay Ignition switch – ignition ON Multifunction control module Shorting link connector NOTE: In certain diagrams (Citroen, Peugeot & Renault), colour codes are replaced by numbers which are used to identify a particular cable and not the colour. In this instance, the cables will be numbered at each end close to the harness connector.

download
UNDER-DASH FUSE/RELAY BOX NOTE: Under-dash fuse/relay box is located under driver’s side of instrument panel. See Fig. 1 or Fig. 2 . Fig. 2: Locating Under-Dash Fuse/Relay Box (1998-2000) Fig. 3: Identifying Under-Dash Fuse/Relay Box Components (1996-2000) Fig. 4: Under-Dash Fuse/Relay Box Legend (1996-2000 – 1 Of 2) UNDER-HOOD ABS FUSE/RELAY BOX NOTE: Under-hood ABS fuse/relay box is located in passenger’s side of engine compartment, on strut tower. See Fig. 6 . Fig. 6: Locating Engine Compartment Fuse/Relay Boxes (1996-2000) Fig. 7: Identifying Under-Hood ABS Fuse/Relay Box Components & Legend (1996-2000)

download
On all models, the fuse panel is located under the instrument panel, left of the steering column. Fig. 4: Interior Fuse Panel Identification (1994-95 Models) 1 – 10 Amp Panel Dimmer, Parking/License Lights, Autoshock Module, Clock 2 – 10 Amp Air Bag Module 3 – 5 Amp Foglight Switch 4 – 10 Amp A/C Clutch 5 – 15 Amp HEGO 1 & 2 (V6 Only) 6 – 10 Amp Anti-Theft, Trunk, Map, Vanity, Glove Box, Underhood, L/H Instrument Panel, Rear Courtesy, Door Courtesy, Lock Cylinder & Dome Lights, Power Mirrors 7 – 10 Amp Turn Signal Indicators/Lights, Backup Lights 8 – 5 Amp Cluster, Rear Defrost Switch, Coolant/Wash Level Sensor, DRL Module, EVO Test, EVO Steering Sensor, ARC (EVO) Module, ARC Switch, Hard Relay, Soft Relay, Auto Mirror, EATC Blend Door, Airbag Module, Overdrive Cancel Switch, Brakeshift Solenoid

download
Check horn fuse 6 in the Power Distribution Center and fuse 7 in the Junction Block. If fuse is blown refer to FUSE BLOWN. If fuse is OK, refer to FUSE OK. Fuse Blown 1. Verify condition of battery terminals and voltage, refer to Battery If battery connections and battery charge is OK proceed to Step 2. . Using a voltmeter, test for battery voltage at both sides of horn fuse 7. If voltage is
OK, on both sides of fuse, proceed to Fuse OK. If voltage is OK, on one side of fuse, the fuse is blown, proceed to Step 3. 3. Using a suitable ammeter in place of the fuse, test amperage draw of the horn circuit. If amperage draw is greater than 20 amps without the horn switch depressed, a grounded circuit exists between the fuse and the horn relay Proceed to Step 4. If amperage draw is greater than 20 amps with the horn switch depressed, a grounded circuit exists between the horn relay and the horn. Proceed to step Step 5. 4. Remove the horn relay from the Junction Block. If the amperage draw drops to 0 amps , the horn switch or circuit is shorted. If the amperage draw does not drop to 0 amps , repair short at the Junction Block.

download
1. NOTE: The location of engine mountings and engine support insulators are described looking from the transaxle to the engine. Remove the front wheels. For additional information, refer to Section 204-04. 2. Remove the battery. For additional information, refer to Section 414-01. 3. Remove the hood. 4. Remove the bolts and the water pump pulley cover. 1. Detach the coolant hose from the clip. 2. Remove the bolts. 3. Remove the cover. 5. Remove the air cleaner (ACL). For additional information, refer to Section 303-12B. 6. Drain the cooling system. For additional information, refer to Section 303-03. 7. Disconnect the accelerator and speed control cables. 1. Detach the cables from the bracket. 2. Disconnect the accelerator and speed control cables. 8. Remove the selector cable. 1. Remove the bolts. 2. Disconnect the cable. 9. Disconnect the bulkhead electrical connectors. 1. Disconnect the electrical connector. 2. Remove the bolt and disconnect the electrical connector. 10. Detach the central junction box (CJB) and position it to one side. 11. Disconnect the cables. 1. Battery cables. 2. Electrical connector. 3. Ground cable. 12. Disconnect the fan motor electrical connectors. 13. Remove the battery bracket bolts and remove the two ground cables. 14. Remove the battery bracket. 15. Disconnect the fuel line. For additional information, refer to Section 310-00. 16. Disconnect the heater hoses. 17. Disconnect the coolant hoses from the radiator and from the coolant passage.