fuse box diagram 2007 saturn ion


You are searching repair manual in PDF format about fuse box diagram 2007 saturn ion use another keyword for search another post or files



  fuse box diagram 2007 saturn ion Direct Download speed 5787 Kb/s

  fuse box diagram 2007 saturn ion Full Version speed 6767 Kb/s




Tips for Power Steering Inoperative/Steering Wheel Hard to Turn 2005-2008 Chevrolet Cobalt 2006-2008 Chevrolet HHR 2005-2006 Pontiac Pursuit (Canada Only) 2007-2008 Pontiac G5 2003-2007 Saturn ION

0

Filed Under (repair and maintenance tips) by admin on 21-04-2010

download
The following diagnostics might be helpful if the vehicle exhibits the conditlon(s) described above. Use the appropriate recommendation based on what symptom has occurred. Recommendation/Instructions No DTCs Review Corporate Bulletin Number 05-02-32-002B to assure you do not have a blown 60 amp steering fuse. The fuse can be blown during improper jump starting of the vehicle on the HHR and ION. Check for this particularly for tow in conditions. DO NOT replace the steering column unless an internal short has been Identified in the column that is causing fuse to blow. Power Steering Warning Message on DIC with DTCs C0176 and C0476 This condition is often the result of excessive lock-to-lock turns of the steering wheel, causing the thermal protection in the Power Steering Control Module (PSCM) to take the steering motor temporarily off line. This is a normal operating characteristic of the system. DO NOT replace the steering column for this condition. Refer to Corporate Bulletin Number 06-02-32-002B for additional information

1998 Honda Civic EX Fuses & Circuit Breakers – Civic IDENTIFICATION

0

Filed Under (Honda) by admin on 27-05-2010

download
UNDER-DASH FUSE/RELAY BOX NOTE: Under-dash fuse/relay box is located under driver’s side of instrument panel. See Fig. 1 or Fig. 2 . Fig. 2: Locating Under-Dash Fuse/Relay Box (1998-2000) Fig. 3: Identifying Under-Dash Fuse/Relay Box Components (1996-2000) Fig. 4: Under-Dash Fuse/Relay Box Legend (1996-2000 – 1 Of 2) UNDER-HOOD ABS FUSE/RELAY BOX NOTE: Under-hood ABS fuse/relay box is located in passenger’s side of engine compartment, on strut tower. See Fig. 6 . Fig. 6: Locating Engine Compartment Fuse/Relay Boxes (1996-2000) Fig. 7: Identifying Under-Hood ABS Fuse/Relay Box Components & Legend (1996-2000)

2006 Saturn ION Body – Front Door Glass Inop/ Uneven Motion

0

Filed Under (Saturn) by admin on 05-07-2010

download
Subject: Front Door Glass Does Not Move Up or Down and/or Inoperative or Uneven Motion (Inspect Window Regulator and Tighten Cam Bolt Torque) Models: 2003-2007 Saturn ION Supercede: This bulletin is being revised to add the 2007 model year. Please discard Corporate Bulletin Number 06-08-64-020 (Section 08 – Body & Accessories). Condition Some customers may comment on either of the following conditions: Condition 1: The front door glass does not move up or down and/or is inoperative. Condition 2: The front door glass moves in an uneven or jerky motion. Cause Condition 1 may be caused by the window regulator sash channel being spread apart where it fastens to clips on the bottom of the door glass. Condition 2 may be caused by a loose cam guide bolt. Correction Remove the door interior trim panel and inspect the window regulator and sash channel. Refer to Trim Panel Replacement – Side Front Door in SI.

VARIABLE VALVE TIMING (VVT) NOISE WHEN STARTING ENGINE 2007 Mazdaspeed 3 2006-2007 Mazdaspeed 6 2007 Mazda CX-7

0

Filed Under (Mazda) by admin on 20-10-2009

APPLICABLE MODEL(S)/VINS
2007 Mazdaspeed3 vehicles with VINs lower than JM1BK******742222 (produced before April 1, 2007)
2006-2007 Mazdaspeed6 vehicles with VINs lower than JM1 GG******109660 (produced before April 1, 2007)
2007 Mazda CX-7 vehicles with VINs lower than JM3ER******166945 (produced before April 1, 2007)
DESCRIPTION
When the engine is first started, some vehicles may exhibit a loud ticking noise from the variable valve timing
(VVT). This is caused by the lock pin of the variable valve timing actuator not fully engaging. Heat treatment has
now been added around the hole of the variable valve timing rotor lock pin to prevent this from happening

download

2007 Chevrolet Impala 4T65E Transmission 1-2 Shift Shudder at Light to Moderate Acceleration (Replace Complete Second Clutch Assembly)

0

Filed Under (Chevrolet) by admin on 21-10-2010

download
Models: 2001-2004 Buick Regal 2001-2005 Buick Century, LeSabre 2002-2007 Buick Rendezvous 2005-2007 Buick Terraza, LaCrosse, Allure (Canada Only) 2006-2007 Buick Lucerne 2001-2005 Chevrolet Venture 2001-2007 Chevrolet Impala, Monte Carlo 2005-2007 Chevrolet Uplander 2006-2007 Chevrolet Malibu SS, Malibu Maxx SS 2001-2002 Oldsmobile Intrigue 2001-2003 Oldsmobile Aurora 2001-2004 Oldsmobile Silhouette 2001-2005 Pontiac Aztek, Bonneville, Montana 2001-2007 Pontiac Grand Prix 2005-2007 Pontiac Montana SV6 2006-2007 Pontiac G6 GTP 2005-2007 Saturn Relay with 4T65E Automatic Transmission (RPOs MN3, MN7, M15, M76) Condition Some customers may comment on a 1-2 shift shudder at light to moderate acceleration. Typically, the throttle plate angle parameter is 12-20% at time of condition with vehicle speed of approximately 24-40 km/h (15-25 mph). The customer may describe the condition as slip or delayed shift into second. Correction Replace the complete second clutch assembly with service kit, P/N 24240561. Refer to the GM Unit Repair Service Manual for the year and model of the vehicle being serviced for the 2nd Clutch service procedure. This service kit contains: Second Clutch Housing Fluid Seal Rings (613), a Second Clutch Assembly (617), a Case Cover (Channel Plate) Upper Gasket (430), and a Case Cover (Channel Plate) Lower Gasket (429). In addition to the content of this service kit, other gaskets not included in this service kit will also be needed to complete the repair – a Case Cover Lower Gasket (429), and a Case Cover Upper Gasket (430). These gaskets can be obtained by ordering gasket kit 24206391. Be sure to use ONLY the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings provided in this service kit. DISCARD the Second Clutch Assembly and Second Clutch Housing Fluid Seal Rings removed from the transmission being serviced. Disassemble ONLY the Oil Pump Assembly from the Case Cover (Complete). DO NOT disassemble the Control Valve Body from the Case Cover. Remove ONLY the Case Cover-to-Case bolts to remove the Case Cover and Valve Body from Transmission Case AS AN ASSEMBLY . To access all Case Cover-to-Case bolts, it is necessary to remove the Pressure Control Solenoid Valve Assembly (322), and 1-2 & 3-4 Shift Solenoid Valve