honda civic sohc vacuum line setup


You are searching repair manual in PDF format about honda civic sohc vacuum line setup use another keyword for search another post or files



  honda civic sohc vacuum line setup Direct Download speed 5787 Kb/s

  honda civic sohc vacuum line setup Full Version speed 6767 Kb/s




2004 Jeep Grand Cherokee Limited DIAGNOSIS AND TESTING – VACUUM RESERVOIR

0

Filed Under (Jeep) by admin on 18-11-2010

download
1. Disconnect vacuum hose at speed control servo and install a vacuum gauge into the disconnected hose. 2. Start engine and observe gauge at idle. Vacuum gauge should read at least ten inches of mercury. 3. If vacuum is less than ten inches of mercury, determine source of leak. Check vacuum line to engine for leaks. Also check actual engine intake manifold vacuum. If manifold vacuum does not meet this requirement, check for poor engine performance and repair as necessary. 4. If vacuum line to engine is not leaking, check for leak at vacuum reservoir. To locate and gain access to reservoir, refer to Vacuum Reservoir REMOVAL /INSTALLATION . Disconnect vacuum line at reservoir and connect a hand-operated vacuum pump to reservoir fitting. Apply vacuum. Reservoir vacuum should not bleed off. If vacuum is being lost, replace reservoir. 5. Verify operation of one-way check valve and check it for leaks. a. Locate one-way check valve. The valve is located in vacuum line between vacuum reservoir and engine vacuum source. Disconnect vacuum hoses (lines) at each end of valve. b. Connect a hand-operated vacuum pump to reservoir end of check valve. Apply vacuum. Vacuum should not bleed off. If vacuum is being lost, replace one-way check valve. c. Connect a hand-operated vacuum pump to vacuum source end of check valve. Apply vacuum. Vacuum should flow through valve. If vacuum is not flowing, replace one-way check valve. Seal the fitting at opposite end of valve with a finger and apply vacuum. If vacuum will not hold, diaphragm within check valve has ruptured. Replace valve.

Related entry:

1994 ford e150 a/c vacuum diagram, 1978 Corvette Vacuum Hose Diagram, how to replace vacuum ressevoir e350 van, algo-charter_if, yhs-d2s_a, 2004 chevy impala vacuum hose line, 2005 ford explorer vacuum line routing, 2006 e250 vacuum check valve, where is the large vaccum line in a 2005 chrysler pacifica, Engine Vacuum Diagrams,

FORD FOCUS ZX3 2000-2003 2.0L ZETEC (DOHC) ECU HONDA / ACURA ACURA RSX/HONDA CIVIC SI 2002-2004

0

Filed Under (Acura, Ford, Honda) by admin on 01-11-2009

Page 1 CHART EXPLANATION B- 12 voltignition U- 12 volt battery E- ECU Ground P- Pressure sensor, Air flow signal
(Note: some applications have multiple “P” signals-Use P(AFR) for AFR and P(FCD) for FCD) I- RPM signal S- Speed Sensor T- Throttle Position Sensor
#- Injector Signal * ALL DIAGRAMS ARE SHOWN FROM THE WIRE SIDE OF THE HARNESS FORD FOCUS ZX3 2000-2003 2.0L ZETEC (DOHC)
ECU LOCATION-4 Hot Wire (0-5V) HONDA / ACURA ACURA RSX/HONDA CIVIC SI 2002-2004 K20A2 ECU LOCATION-3 Pressure Sensor Type HONDA CIVIC 1988-1991 ACURA INTEGRA 1986-1993
The following diagrams may differ slightly depending on vehicle year, or model (California or Federal). Confirm that the diagram shown
corresponds to your vehicle by referencing the factory repair manual. Locate the engine control unit (ECU) using the diagram below.
FORD FOCUS ZX3 2000-2003 2.0L ZETEC (DOHC) ECU HONDA / ACURA ACURA RSX/HONDA CIVIC SI 2002-2004

download

Related entry:

honda maintenance codes chart, honda maintenance codes, how to remove 96 honda driver door, firing order for civic 1 7, honda ballade 150 service manual, honda insight undercarriage manual, adding refrigerant to a 2010 honda civic, free 2001 Acura CL Manual, 2000 honda civic freon capacity, p2647 honda code on a 2007 element,

2003–05 Honda Civic Hybrid With CVT 2001–05 Honda Insight With CVT CVT Drive Belt Slippage

0

Filed Under (Honda) by admin on 10-06-2010

download
On affected vehicles, the CVT (continuously variable transmission) drive belt may slip during acceleration. To increase customer confidence, American Honda is extending the warranty for this potential problem to 7 years or 100,000 miles, whichever comes first. This extended warranty covers only CVT drive belt slippage and CVT start clutch judder below 15 mph (see Service Bulletin 07-049, Warranty Extension: CVT Start Clutch Judder). Any other customer complaints with the CVT are covered by the normal 3-year, 36,000-mile new vehicle limited warranty. Do the diagnosis in this service bulletin. Then, only if needed, install a CVT lower valve body kit and update the ECM (Civic Hybrid), or replace the CVT (Civic GX, Civic HX, and Insight).

Related entry:

remove transmission cvt from 05 hondacivic hybred, burnishing clutch procedure honda, burnishing cvt civic transmission, ESTIMA HYBRID BATTERY DISCONNET, honda city cvt transmission problem, honda city cvt transmission problems, honda city transmission problem,

2006 Honda Civic SI Supercharger Kit Installation Instruction

0

Filed Under (Honda) by admin on 12-04-2010

download
Comptech Supercharger kit for the 2006 Honda Civic SI. All components have been designed and manufactured utilizing the latest in technology and materials. Please take a moment to read this instruction manual and warranty information page thoroughly before starting any work. Always work in a clean environment and use the appropriate safety equipment and tools to avoid any potential damage or injuries. Comptech recommends the use of a Genuine Honda Service Manual to supplement these instructions. All Comptech products are intended to be installed by a professional installer. Many stock parts are reused during installation. Do not damage or discard any pieces during disassembly or installation. We recommend marking any hose or wire before disconnecting to avoid confusion
during reassembly

2005 Chevrolet Malibu Vacuum Brake Booster Check Valve and/or Hose Replacement Removal Procedure

0

Filed Under (Chevrolet) by admin on 19-10-2010

download
1. Disconnect the brake booster vacuum check valve (1) from the brake booster. 2. If the vacuum check valve (1) needs to be separated from the vacuum hose (3), release and reposition the clamp (2) on the vacuum hose (3) and remove the check valve (1) from the hose (3). 3. If replacing the vacuum check valve (1), remove the grommet (4) from the brake booster and discard the grommet. 4. If removing the vacuum hose (2), take note of the vacuum hose routing then disconnect from the engine intake manifold connection (3) by releasing tension on the vacuum hose clamp (1) and sliding the vacuum hose (2) off the intake manifold connection (3). Installation Procedure Important: A small amount of denatured alcohol can be used as an assembly aid when installing the vacuum check valve and/or grommet. Do NOT use soap. 1. If the vacuum hose (2) was removed, install the vacuum hose into position on the vehicle as noted prior to removal, then connect the vacuum hose (2) to the engine intake manifold connection (3) and secure with the vacuum hose clamp (1). 2. If the vacuum check valve (1) is being replaced, install a NEW grommet (4) to the brake booster. 3. If the vacuum check valve (1) was separated from the vacuum hose (3), install the check valve (1) to the vacuum hose (3). Install and secure the clamp (2) into position on the hose (3). 4. Connect the brake booster vacuum check valve (1) to the brake booster.

Related entry:

vacuum hoses routing 2003 impala, 2000 ford excursion vacuum diagram manual, kia sadona 2005 vacuum lines, 2002 ford focus throttle body vacuum hose, 2003 f150 vacuum hoses locations, 2002 vw gti 1 8t vintage air hose diagram, vacuum line under a 2005 dodge grand caravan you tube, 231d transfer case vacuume removal, 2007 f150 4wd vacuum hose diagram, vacuum hose drawing for 2007 dodge charger,