how do you remove the back seat of a hyundai Azera


You are searching repair manual in PDF format about how do you remove the back seat of a hyundai Azera use another keyword for search another post or files



  how do you remove the back seat of a hyundai Azera Direct Download speed 5787 Kb/s

  how do you remove the back seat of a hyundai Azera Full Version speed 6767 Kb/s




1993 Mitsubishi Montero TRANSFER CASE DISASSEMBLY

0

Filed Under (Mitsubishi) by admin on 30-12-2010

download
Disassembly (Ram-50) 1) Remove both 4WD indicator switches and steel balls. Remove speedometer gear assembly. Remove output shaft cover, gasket, wave spring and spacer. See Fig. 3. Remove rear cover, rear cover gasket and spacer from chain cover. Drive roll pin out of high-low shift fork. 2) Remove 2 seal plugs. Remove 2 poppet springs and steel balls. Shift transfer case to “4WD” and pull high-low shift rail out, in rear cover direction. Remove interlock plunger. Remove pulse generator (if equipped), front output shaft cover and pulse rotor (if equipped). Remove snap ring from rear bearing on output shaft. Remove chain cover, oil guide and side cover. Remove countershaft locking plate. Remove countershaft. 3) Remove countergear, 2 thrust washers, 2 needle bearings and spacer through side cover opening. Remove snap ring, spring retainers and spring from 2WD-4WD shift rail. Remove front output shaft, rear output shaft and chain as assembly. 4) Remove 2WD-4WD shift fork and distance piece. Drive out 2WD-4WD shift rail spring pin. Remove 2WD-4WD shift rail and lug. Remove high-low shift fork and high-low synchronizer sleeve. Remove needle bearing and snap ring from input gear. Remove input gear assembly. 5) If either control shaft or input gear oil seals are to be replaced, drive out roll pin from transmission control change shifter. Separate transfer case from adapter. See Fig. 3. Disassembly (Montero) 1) Remove dynamic damper, 5 detection switches and 3 steel balls. Remove poppet plug, spring and steel ball. Remove speedometer gear assembly. Remove output shaft rear cover, spacers, dust seal guard and oil seals. Front output shaft cover, wave spring and spacer (if equipped). 2) Remove high-low shift rail plug and high-low shift fork spring pin. Shift transfer case to “4WD”. Remove rear cover and high- low shift rail. Remove interlock plunger. Remove rear output shaft (viscous coupling) assembly and center differential assembly. Remove 2WD-4WD synchronizer assembly, chain and front output shaft from transmission as a unit. With White paint make match marks in grooves of 2WD-4WD synchronizer in 3 places. With White paint make match marks on spline projections of 2WD-4WD synchronizer sleeve in 3 places. Refer to match marks during reassembly. 3) Remove snap ring, spring seat, spring, 2WD-4WD shift fork and 2WD-4WD synchronizer sleeve. Remove differential lock hub, oil dam cover and bearing retainer. Remove side cover and gasket. Remove transfer counter gear shaft, transfer counter gear, thrust washer, needle bearings and spacer. Remove transfer drive shaft assembly. Remove high-low shift fork assembly and clutch sleeve. Remove transfer input gear assembly. 4) Remove 2WD-4WD shift lug spring pin, spring, spring retainer 2WD-4WD shift lug and shift rail. Remove input gear oil seal, baffle plate, dust seal guard and front output shaft oil seal. See Fig. 4.

Related entry:

location of retaining bolts on peugeot 307 bumper, 2002 chrysler voyager front bumper cover removal, Crank pulley Torque settings jaguar x type, how to instal a gearshift level tube on a 97 expedition, removing egr valve on toyota tacoma 2 4, buick lesabre 2004 removal storage tray in dash, how to remove smax dashboard, pontiac aztek shifter light, lincoln dash console removal pdf, how to remove 1995 ford escort timing cover,

2004–2010 Toyota 4Runner Front Seat Squeak Noise

0

Filed Under (Toyota) by admin on 20-05-2011

download
Some customers may experience a squeak noise due to contact between the seat track locating pin(s) and the ?oor pan location hole(s). The following procedure describes the repair method to correct this condition. 1. Disconnect the negative (–) battery terminal. 2. Remove the plastic front seat track covers, use a Plastic Pry Tool to disengage the claws and carefully remove the plastic seat track covers. NOTE Refer to the appropriate Toyota Repair Manual for each model for detailed instructions on how to remove the plastic seat track covers. 4. Remove the LH front seat assembly. A. Move the seatback to the full upright position. B. Remove the four (4) seat track securing bolts. C. Disconnect the electrical connectors and remove the complete seat assembly. 5. Remove the seat track locating pins. A. With the seat removed from the vehicle, tilt the seat assembly backward to gain access to the seat track locating pins. B. Use a power cut-off tool to cut off the two (2) locating pins leaving 2 mm (0.1 in.) or less of each pin. NOTE • Do NOT permit the power cut-off tool to contact the seat track. ONLY cut off the shaft of the pin (near the base of the seat track). • The seat track locating pins’ function is to ease installation during manufacturing and does NOT provide any other function. Figure 5.. 6. Clean and paint bare metal surfaces. A. Remove any metal shavings from the seat track/seat assembly. B. Clean the bare metal surface of the remainder of the seat track locating pin with wax, grease, and silicone remover. C. To prevent corrosion, coat any bare metal surfaces still attached to the seat track with a brush-on type paint. 7. Install LH front seat assembly. A. Place the seat on the cabin ?oor. B. Reconnect all electrical connectors under the seat. C. Install all four (4) seat track retaining bolts (?ngertight). D. Tighten the two (2) front seat track attaching bolts. NOTE The bolt torque speci?cation varies by model. Please refer to the Repair Manual for the correct bolt torque for the model you are working on. E. Tighten the two (2) rear seat track attaching bolts. NOTE The bolt torque speci?cation varies by model. Please refer to the Repair Manual for the correct bolt torque for the model you are working on. F. Reinstall all plastic seat track covers. 8. Repeat steps 1 – 6 for the RH seat assembly. 9. Reconnect the negative (–) battery terminal. 10. Test power seat operation and seat heater (if equipped) for proper operation. 11. Initialize front passenger occupant classi?cation system and re-initialize any other power systems. Refer to the applicable model and model year repair manual initialization procedures. 12. Inspect SRS warning light operation. 13. Test drive vehicle and con?rm that the seat squeak has been eliminated.

Related entry:

1996 toyota land cruiser seat reapair power motor, how to repair power seat for 96 landcruiser, 2005 kia optima driver 8way power seat switch, seat ibiza 2001 manual, seat alhambra front brake assembly diagram, 2003 expedition heated seat diagram, how to fix 2006 honda odyssey driver seat, isuzu rodeo seat won\t recline, honda passenger seat schematic, how to replace a Track Gear 96 landcruiser,

1994 Ford Mustang A/C Evaporator Housing Removal and Installation

0

Filed Under (Ford) by admin on 06-03-2011

download
1. Disconnect battery ground cable (14301) . 2. Remove two console armrest mounting access covers (047A62) at rear of console panel (045A36) (snaps out) to gain access to armrest retaining bolts. 3. Remove four armrest-to-floor bracket retaining bolts and remove armrest assembly (snaps out of console). 4. Remove console panel gear shift plate (044G24) (snaps out). On vehicles equipped with manual transmissions, shift boot is attached to bottom of finish panel. Remove shift knob and slide boot and console panel gear shift plate up shift lever to remove. 5. To remove top finish panel position emergency brake lever in the UP position. Remove four retaining screws and lift top finish panel up. Disconnect necessary wire connectors. 6. Remove two console-to-rear floor bracket retaining screws. 7. Insert a small screwdriver into two notches at bottom of front upper finish panel and snap out. 8. If the vehicle has a radio chassis (18806) , the radio chassis must be removed. Refer to Section 15-01. If the vehicle doesn’t have a radio chassis , use a small screwdriver and pry radio cover finish panel out of console. 9. Flex glove compartment bin tabs inward. Drop down glove compartment (06010) assembly. Remove two console-to-instrument panel retaining screws. 10. Remove four console bracket retaining screws. Remove console panel from vehicle. 11. Remove three bolts retaining steering column opening cover (3A673) and reinforcement panel. Remove cover. 12. Remove steering column opening reinforcement by removing two bolts. 13. Remove two bolts retaining steering column opening reinforcement and remove reinforcement. 14. Remove six steering column retaining nuts (two retaining the hood release mechanism and four retaining column to lower brake pedal support). Lower steering column to floor. 15. Remove upper and lower steering column shrouds (3530) and disconnect wiring from turn signal and windshield wiper switch (13K359) . 16. Remove steering column through bolt and nut on engine compartment side of cowl panel. Remove steering column from vehicle. 17. Remove brake pedal support nut. 18. Snap out instrument panel defroster opening grille (044E82) . 19. Remove screws from speaker covers. Snap out speaker covers. 20. Remove front screws retaining RH and LH scuff plates at cowl side trim panels. 21. Remove RH and LH cowl side trim panels. 22. Disconnect wiring at RH cowl side. 23. Remove cowl side retaining bolts (one each side). 24. Remove five cowl top screws attachments. 25. Gently pull instrument panel (04320) away from RH side of cowl panel. Disconnect speedometer cable, air conditioning controls and wire connectors. 26. Place a drain pan or suitable container under the heater water hose connections at the cowl panel. 27. Disconnect heater water hoses (18472) from heater core tubes and plug heater water hoses with suitable 5/8-inch and 3/4-inch plugs. Cap heater core tubes to prevent coolant loss from heater core (18476) during removal of heater case. 28. Remove screw retaining A/C evaporator case support bracket (19A639) to cowl top panel. 29. Disconnect vacuum supply supply hose (black) from A/C vacuum supply in engine compartment. 30. Working under the hood (16612) , remove nut retaining heater case to cowl panel. 31. Inside passenger compartment, remove screw retaining A/C evaporator case mounting bracket (19A865) to cowl top panel. 32. Remove one screw retaining A/C evaporator case mounting bracket below heater case to cowl panel. 33. Carefully pull heater case from cowl panel and remove heater case assembly from vehicle. 34. To install, reverse Removal procedure. Check operation of all components. 35. After repairs have been completed, check the coolant level in the radiator (8005) and in the radiator coolant recovery reservoir (8A080) . Fill as required with the recommended coolant mixture.

Related entry:

2004 touareg shifter lever, how to remove 1998 navigator overhead console, removing center console on lincoln aviator, trailblazer cowl removal, special tool 2002 windstar remove radiator, how to remove liftgate panel on 2012 nissan rogue, how to remove center console of 2008 sebring, how to remove console from kia sportage 2000, remove console lid ford escape, how to replace tailgate trim on a 2007 subaru outback,

2008 Dodge Charger Seat Back Cushion / Cover Second Row REMOVAL

0

Filed Under (Dodge) by admin on 02-08-2010

download
1. Remove the seat cushion. See: Seat Cushion\Service and Repair\Seat Cushion / Cover – Removal 2. Remove the nut and disconnect the seat belt anchor. 60/40 Seat Back – Wagon 40% SEAT BACK SIDE 1. Fold the 40% section of the seat (2) down. 2. Remove the nuts (5). 3. Pivot the seat back off the pivot pin (3) located on the 60% seat back. 4. Remove the seat back from vehicle. 60/40 Seat Back – Wagon 60% SEAT BACK SIDE 1. With the 40% seat back removed. 2. Fold the 60% section of the seat down. 3. Remove the four nuts attaching seat back (5). 4. Remove the seat back for vehicle. 60/40 Seat Back – Domestic Sedan 40% SEAT BACK SIDE 1. Fold the 40% section of the seat (3) down. 2. Remove the two nuts (4) attaching seat back. 3. Pivot the seat back off the pivot pin (1) located on the 60% seat back (2). 4. Remove the seat back from vehicle. 60/40 Seat Back – Domestic Sedan 60% SEAT BACK SIDE

Related entry:

2006 ford explorer Part Number for rear passenger side third row seat motor is:, how to remove electric seat 2002 lincoln ls, 2006 ford explorer 3rd row seat motor, replace third row seat cable ford explorer, replace third row seat back release cable ford explorer, repairing escalade seat 2008 warmers, repair 2006 ford explorer XLT 3rd row seat, remove rear seat custions Honda Pilot, instructions on how to remove rear seat in a 2002 lincoln ls, how to replace 3rd row seat motor 2006 ford explorer,

2008 Dodge Charger Seat Back Cushion / Cover – Removal

0

Filed Under (Dodge) by admin on 31-07-2010

download
1. Remove the seat cushion. See: Seat Cushion\Service and Repair\Seat Cushion / Cover – Removal 2. Remove the nut and disconnect the seat belt anchor. 60/40 Seat Back – Wagon 40% SEAT BACK SIDE 1. Fold the 40% section of the seat (2) down. 2. Remove the nuts (5). 3. Pivot the seat back off the pivot pin (3) located on the 60% seat back. 4. Remove the seat back from vehicle. 60/40 Seat Back – Wagon 60% SEAT BACK SIDE 1. With the 40% seat back removed. 2. Fold the 60% section of the seat down. 3. Remove the four nuts attaching seat back (5). 4. Remove the seat back for vehicle. 60/40 Seat Back – Domestic Sedan 40% SEAT BACK SIDE 1. Fold the 40% section of the seat (3) down. 2. Remove the two nuts (4) attaching seat back. 3. Pivot the seat back off the pivot pin (1) located on the 60% seat back (2). 4. Remove the seat back from vehicle. 60/40 Seat Back – Domestic Sedan 60% SEAT BACK SIDE

Related entry:

2005 honda pilot seat heater repair procedure, honda pilot 2006 seat removal, honda pilot remove seats, rear seat removal 2002 mercury cougar, remove bench seat honda pilot,