how to fix door handle on a mitsubishi pajero 93


You are searching repair manual in PDF format about how to fix door handle on a mitsubishi pajero 93 use another keyword for search another post or files



  how to fix door handle on a mitsubishi pajero 93 Direct Download speed 5787 Kb/s

  how to fix door handle on a mitsubishi pajero 93 Full Version speed 6767 Kb/s




1999 Dodge Grand Caravan Trim Panel: Service and Repair REMOVAL INSTALLATION

0

Filed Under (Dodge) by admin on 20-09-2010

download
Trim Panel: Service and Repair REMOVAL 1. Using a trim stick (C-4755), pry courtesy lamp from door trim. 2. Disconnect wire connector from courtesy lamp. 3. If equipped, remove screws attaching door assist handle to inner door panel. 4. If equipped, remove screw attaching door pull cup to inner door panel. 5. If equipped, remove screws attaching trim panel to door from below map pocket. 6. If equipped, remove window crank. 7. Using a trim stick, remove screw cover from switch panel. 8. Remove screws attaching switch panel to door trim. 9. Remove power accessary switch from door trim. 10. Disconnect power switch from wire connector. 11. If equipped, using a small, flat bladed pry tool, remove memory seat/mirror switch and disconnect wire connector. 12. If equipped, remove screw holding door trim to door panel from behind inside latch release handle. 13. Disengage clips attaching door trim to door frame around perimeter of panel. 14. Lift trim panel upward to disengage flange from inner belt molding at top of door. 15. Tilt top of trim panel away from door to gain access to latch linkage. 16. Disengage clip attaching linkage rod to inside latch release handle. 17. Separate linkage rod from latch handle. 18. Remove front door trim panel from vehicle. INSTALLATION 1. Hold top of trim panel away from door to gain access to latch linkage. 2. Place linkage rod in position on latch handle. 3. Engage clip to hold linkage rod to inside latch release handle. 4. Place front door trim panel in position on door. 5. Install trim panel into inner belt molding at top of door. 6. Install clips to attach door trim to door frame around perimeter of panel. 7. If equipped, install screw to attach door trim to door panel behind inside latch release handle. 8. If equipped, connect power switch into wire connector. 9. Place power accessary switch in position on door trim. 10. Connect wire connector into memory seat/mirror switch and install switch into trim panel. 11. Install screws to attach accessary switch panel to door trim. 12. Install screw cover into switch panel. 13. If equipped, install window crank. 14. If equipped, install screws to attach trim panel to door inside map pocket. 15. If equipped, install screw to attach door pull cup to inner door panel. 16. If equipped, install screws to attach door assist handle to inner door panel. 17. Connect wire connector into courtesy lamp. 18. Install lamp in door trim.

Related entry:

rav4 driver side panel remove, 2002 acura mdx removing door panels, door panel removal 2008 astra, 2006 rav4 back door latch adjustment, INSIDE DOOR PANNEL OF 2008 JEEP LIBERTY LOCK MECKINSOM, removing doorbpanel warranty on 2008 impala, 2006 highlander door trim panel removal, remove rav 4 2003 door panel, 2002 acura mdx removing reardoor panels, 2005 avalanche door handle removal,

2009 Holden VE Sedan Front Side Door Trim Panel Replacement Removal Procedure

0

Filed Under (GM) by admin on 16-04-2011

download
Note: Pry the inside door handle to door retaining screw cover (1) using a suitable tool. • Remove the inside door handle to door retaining screw cover (1) from the door trim panel (3). • Remove the inside door handle to door retaining screw (2).• Remove the door trim panel to door retaining screws (1). Note: Firmly pull on the armrest handle to release the door trim panel to door retaining clips. • Remove the door trim panel from the door to allow access to door handle cable, door lock cable and courtesy light electrical connectors (if fitted). Note: The door handle and lock cables slide out and lift up to remove from the door trim panel. • Disconnect the inside door handle cable (1) and door lock cable (2) from the door trim panel. • Disconnect the courtesy light electrical connectors (1) from the door trim panel (2) (if fitted). • Remove the door trim panel (2) from the door. Installation Procedure Note: Green retaining clips are along the front edge and white retaining clips are along the back edge. • Make sure that all of the retaining clips are on the door trim panel and not still attached to the sheetmetal. Note: Do not fully install the door trim panel at this stage. The inside door handle cable, door lock cable and courtesy light electrical connector have to be attached first (if fitted). • Position the door trim panel to the door.

Related entry:

how to replace rx300 lock cable, 2002 Liberty heater door repair, replacement of temperature actuator on 2003 buick lesabre step by step instructions, how to fix a door handle on a 1997 chevy suburban, rx 300 door lach cable, door ajar light on aztek 2002, auto zone door check 2005 equinox, driver side door schematics for a 2009 dodge journey, 2011 chevy express van sliding door not closing, 2005 chevy 3500 express van sliding door handle,

1996 Lincoln Town Car Power Window Regulator REMOVAL AND INSTALLATION

0

Filed Under (Lincoln) by admin on 31-03-2011

download
Window Regulator, Power Front Door—Town Car Removal 1. CAUTION: When servicing front door power window regulator minus motor (23208), regulator cable tension must not be altered. Cable tension is preset at production. Improper adjustment may result in premature front door power window regulator failure or erratic operation. CAUTION: Be careful not to drill through the window regulator behind inner door panel. Additional repairs may be necessary. If front door window glass (21410) is in the down position and is inoperable, a through f must be taken; if front door window glass is operational, proceed to Step 2. a. Remove front door trim panel (23942) and front door trim shield (237A04). Refer to Section 01-05. b. Disconnect battery ground cable (14301). Refer to Section 14-01. c. CAUTION: Be careful not to strike or scratch front door window glass. Remove three 1/4 inch rivets retaining window regulator electric drive (23394) to inner panel. d. Working through front access hole in inner panel, remove three screws from window regulator electric drive. e. Separate window regulator electric drive from front door power window regulator minus motor. Raise front door window glass by hand and secure using tape. f. Proceed to Step 2. 2. Remove front door window glass as outlined. 3. Disconnect window regulator electric drive wiring connector. 4. Remove two upper front door power window regulator retaining nuts. 5. NOTE: Use care not to enlarge sheet metal holes in the door inner panel. Remove two 1/4-inch rivets retaining front door power window regulator minus motor to inner door panel. 6. Remove front door power window regulator minus motor from front door (20124). Installation 1. Lubricate front door power window regulator minus motor with Teflon® Lubricant E7FZ-19590-A or equivalent meeting Ford specification ESB-M1C111-A as outlined. 2. Install front door power window regulator minus motor into access hole in inner panel. 3. Position front door power window regulator minus motor using upper front door power window regulator studs and tabs on window regulator electric drive mounting bracket. 4. Install rivets retaining front door power window regulator minus motor to door inner panel (1/4-20 x 1/2 inch screw and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used as alternates). 5. Install two upper front door power window regulator retaining nuts. 6. Install Front Door Window Glass as outlined. 7. Adjust Front Door Window Glass as outlined. 8. Install front door trim shield and front door trim panel. Refer to Section 01-05. Front Door—Crown Victoria, Grand Marquis Removal 1. If front door window glass is in the down position and is inoperable, the following steps must be taken; if front door window glass is operational, go to Step 2. a. Remove front door trim panel and front door trim shield. Refer to Section 01-05. b. Disconnect battery ground cable. Refer to Section 14-01. c. Disconnect window regulator electric drive wires. d. CAUTION: Be careful not to strike or scratch front door window glass because it could break. Remove window regulator electric drive retaining screws through holes. e. Remove window regulator electric drive from front door power window regulator minus motor.

Related entry:

1994 cadallic brougham window fuse, 2008 Dodge Avenger Window Diagram, power window switch 06 Mercedes C230, 2003 jetta blend air door, actuator nissian micra, used window winders manually opertated, 2000 avalon front door cables, 2005 kia sedona door window motor, remove window regulator on 2011 kia sorento, 2002 taurus power windows schematic,

1994 Lincoln Town Car Door Window Glass Front Removal Installation

0

Filed Under (Lincoln) by admin on 11-03-2011

download
Front Removal 1. Remove front door trim panel (23942) and front door trim shield (237A04). Refer to Section 01-05. 2. Loosen front door glass run front retainer retaining screw and position front door glass run front retainer (21572) forward. 3. Lower front door window glass (21410) to gain access to two front door window channel bracket (23288) rivets and remove the center pins from rivets using a drift punch. Using a 1/4-inch diameter drill, drill out remainder of rivets. CAUTION: Do not attempt to pry out the rivets as damage to the front door window glass could result. NOTE: Prior to removing the rivet center pins, it is recommended that a suitable block support be placed between the door outer panel and the front door window channel bracket to stabilize the front door window glass during rivet removal. 4. Remove front door window glass . Installation 1. Insert front door window glass into front door (20124) between front door belt line outside weatherstrip (21452) and inner panel. 2. Position front door window glass into door frame and lower front door window glass to align with front door window channel bracket . 3. Install two 1/4-inch rivets using Rotunda Blind Fastener Installation Tool 107-00600 or equivalent (use of 1/4-20 X 1-inch screw and washer assemblies and 1/4-inch-20 nut and washer assemblies is optional). Equivalent metric fasteners may also be used. NOTE: Torque must not exceed 9-14 Nm (7-10 lb-ft). 4. Adjust front door window glass as outlined. 5. Install front door trim shield and front door trim panel. Refer to Section 01-05. Rear Removal 1. Remove rear door trim panel (27406) and watershield. Refer to Section 01-05. 2. Remove rear door glass run front lower retainer (25796) as outlined. CAUTION: Do not attempt to pry out the rivets as damage to the rear door window glass (25712) could result. Prior to removing rivet center pins, it is recommended that a suitable block support be placed between door outer panel and rear door window channel bracket to stabilize rear door window glass during rivet removal. 3. Lower rear door window glass to gain access to the two rear door window channel bracket retaining rivets and remove center pins from rivets using a drift punch. Using a 6.35mm (1/4-inch) diameter drill, drill out the remainder of the rivets. 4. Remove rear door window glass.

Related entry:

07 yaris passenger window weather stripping, removing the lower door molding on a ls430, lexus ls 430 door chrome removal, how to replace rear door glass on a impreza, how to replace rear door glass chevy door glass, how to remove door card pocket lupo, googleprogramming door glass on 2009 ford flex, driver door kia sorento not opening from outside, 90 plymouth door window glass adjustment, 2010 lincoln mkz weather stripping,

2004 Pontiac Montana Trim Panel Replacement – Side Front Door

0

Filed Under (Pontiac) by admin on 26-10-2010

download
Removal Procedure 1. Open the door. 2. Remove the front door trim plate. Refer to Door Trim Plate Replacement () . 3. Remove the front door manual window regulator handle if equipped. Refer to Window Regulator Handle Replacement – Door Remove the armrest screws. Route the electrical harness through the front door trim panel opening. Use J 38778 in order to remove the front door trim panel from the door. Use J 38778 in order to pry the front door trim panel from the door frame at the window seal. 8. Remove the front door trim panel from the door. 4. 5. 6. 7. Installation Procedure 1. Install the front door trim panel to the front door. 2. Place the window seal portion of the panel over the door frame. 3. Route the electrical harness through the front door trim panel opening and into place. 4. Align the front door trim panel retainers to the holes in the door metal. 5. Firmly press the front door trim panel to the door metal in order to seat the retainers. Notice: Refer to Fastener Notice in Cautions and Notices. 6. Install the armrest screws. Tighten the screws to 3 N.m (26 lb in). 7. Install the front door manual window regulator handle if equipped. Refer to Window Regulator Handle Replacement – Door 8. Install the door trim plate. Refer to Door Trim Plate Replacement () . 9. Close the door.

Related entry:

door panel armrest for 2007 honda crv, how to fix a armrest on a 2004 Honda CRV?, pontiac montana glass door repair, pontiac vibe door trim installation instructions, upper door weatherstrip for 2005 pontiac G6,