Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
- with CODE (848) Electric pivoting side window Remove/Install 1 Remove paneling on C-pillar 2 Secure window against falling down. NOTE: To avoid damage to window or paintwork 3 Unscrew bolts (A) at hinges Screw for side window hinge to C pillar = 12 Nm 4 Pull back cover at opening mechanism Pull back cover at opening mechanism NOTE: For access to connecting point at opening mechanism. 5 Remove window NOTE: Caution: Do not damage window and paint if adhesive tape or support is removed Extend window toward top (B). Check seal. If necessary, replace seal of side window. 6 Install in the reverse order

download
- with CODE (U49) Styling Package Remove/Install 1 Remove cover (1) from bumper NOTE: Do not break retaining lugs. 2 Remove bulb housing (2) NOTE: To unlock, rotate counterclockwise. Installation: Ensure that the locking device has locked securely. 3 Remove fog lamp insert (6) from housing Installation wedge: See Special Tools below. 4 Disconnect connector (4) 5 Remove bulb on the back of the fog lamp insert (6) CAUTION: Do not hold the bulb with bare fingers, as fingerprints bake and leave behind opaqueness on the bulb. Use a soft, lint-free cloth. NOTE: Lock securely. 6 Install in the reverse order Special Tools

download
AR68.20-P-2020GI Remove/Install Rear Center Console – Models 163.154/174 #A as of 289565 – Models 163.157/175 (all) Remove/Install 1 Remove armrest lid (1) 2 Remove stowage box in the center console NOTE: Press the center pin approx. 4 mm downwards, then remove the rivet upwards 3 Remove screws (2) on the cup holder 4 Remove inner part of ashtray 5 Remove ashtray trim (3) CAUTION: Risk of breaking the clips (4) NOTE: Loosen clips (4) and pull back the lower edge of the cover and remove upwards 6 Remove screws (5) 7 Unclip rear center console (6) above (arrows) Long wedge: See Special Tools below. 8 Remove rear center console (6) from the center console 9 Disconnect plug from control module of rear control panel and ashtray NOTE: Disconnect plug of the rear ashtray from ashtray housing 10 Install in the reverse order Special Tools Long Wedge P/N # 115 589 03 59 00

download
This How-to is based of the 2006 Toyota Corolla LE Step 1. Disconnect battery lead because of air bag sensors [Note: you WILL lose all of your radio presets…so you might want to write them down before moving forward.] Step 2. Pop off trim around shifter stick (I just lifted it up form the bottom with my finger nails) Step 3. Disconnect the Aux power, (not necessary, but it gets stuff out of the way) it just pulls right off Step 4. Remove center knob on the A/C panel (Just pull it straight out). Remove Phillips screw behind the knob this is the only screw that has to come out (in addition to the 4 radio screws) Step 5. Pull the a/c console forward. It’s a tight fit but it’s only held by clips. This was the most difficult part for me because I didn’t want to break anything. It eventually released after pulling with constant pressure. I found that pulling from the inside of the knob helped allot. Once the top part was off, pulling from the right edge of the console released the rest of it. Step 6. Disconnect these 4 Cables. Once you have done so the whole center console comes right out (make sure that the car is in neutral or else the shifter will be in the way and you won’t be able to take out the center console.) (I don’t think this step is necessary but again, it gives you more room to work and the doesn’t take any time at all to do so) (What it looks like then the shifter plate and the center console are removed)

download
Removal 1. Remove the rear driveshaft assembly. 2. Using the special tool, remove the pinion nut. 3. Index-mark the location of the rear axle pinion flange. 4. Using the special tool, remove the rear axle pinion flange. 5. Using the special tool, remove the rear pinion oil seal. Installation Note: Make sure that the mating surface is clean before installing the new seal. 1. Using the special tool, install a new rear pinion oil seal. Note: Lubricate the pinion flange with grease. 2. Line up the index marks and position the pinion flange. 3. Using the special tool, install a new pinion nut. 4. Install the rear driveshaft assembly.