how to remove ford focus console trim


You are searching repair manual in PDF format about how to remove ford focus console trim use another keyword for search another post or files



  how to remove ford focus console trim Direct Download speed 5787 Kb/s

  how to remove ford focus console trim Full Version speed 6767 Kb/s




2010 Ford Taurus Console Floor REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 08-03-2011

download
Trim Panels, Mouldings And Fasteners NOTE: Floor console with navigation shown, floor console without navigation similar. Trim Panels And Fasteners NOTE: Floor console with navigation shown, floor console without navigation similar. Removal and Installation 1. Place the selector lever in the NEUTRAL position. 2. Position the front seats to the full rearward and downward positions. 3. Pull the middle and rear of the floor console LH and RH lower trim panels outward to release the retaining clips. 4. NOTICE: Damage to the floor console upper trim panels may occur if cardboard is not used to remove the floor console lower trim panels. NOTE: Floor console LH lower trim panel shown, floor console RH lower trim panel similar. Position a piece of cardboard between the floor console LH and RH lower trim panels and floor console. 5. Remove the floor console LH lower trim panel. Push the floor console LH lower trim panel toward the front of the vehicle to detach the trim panel from the pin-type retainer. 6. Remove the floor console RH lower trim panel. Pull the floor console RH lower trim panel down toward the floor of the vehicle to detach the trim panel from the pin-type retainer. 7. Position the front seats forward. 8. Remove the 2 floor console lower rear screws. 9. Position the front seats rearward. 10. Remove the steering column opening trim panel in the following sequence. 1. Remove the 2 steering column opening trim panel screws. 2. Pull the steering column opening trim panel down toward the floor of the vehicle to release the retaining clips. 11. Remove the floor console LH and RH finish mouldings in the following sequence. 1. Lift up the rear of the floor console finish mouldings to release the retaining clips from the floor console. 2. Pull the floor console finish mouldings toward the rear of the vehicle to release the retaining clips from the center instrument finish panel. 3. Disconnect the trunk release switch and start/stop button electrical connector, if equipped. NOTICE: Damage to the floor console may occur if cardboard is not used to remove the floor console upper trim panel. NOTE: Floor console LH upper trim panel shown, floor console RH upper trim panel similar. 12. Remove the floor console LH upper trim panel in the following sequence. 1. Pull the rear of the floor console LH upper trim panel away from the floor console, releasing the retaining clips. 2. Position a piece of cardboard between the floor console LH upper trim panel and floor console. 3. Pull the floor console LH upper trim panel toward the rear of the vehicle to release the retaining clips from the instrument panel. 13. Remove the 2 pushpin carpet retainers, 4 floor console lower front and middle screws. 14. Remove the selector lever bezel. For additional information, refer to Section 307-05. 15. Remove the media bin/storage compartment in the following sequence. 1. Remove the 4 screws and lift up the media bin/storage compartment. 2. Disconnect the electrical connector(s). 16. Disconnect the floor console bulkhead electrical connector. 17. Detach the wire harness pin-type retainer from the floor console. 18. Remove the 2 floor console upper bolts. 19. Disconnect the selector lever cable from the selector lever.

Related entry:

f 250 armrest squeak, 2004 explorer overhead console bracket, 2004 tahoe console removal, 2005 f-150 center console, 2007 honda accord console pocket lid, how to open rear console box for lexus gx 470, how to remover cup holder console from chevy equinox, how to remove console in suzuki forenza, hhr shifter replacement cost, how to remove center counsole on 2006 pilot,

1994 Ford Mustang A/C Evaporator Housing Removal and Installation

0

Filed Under (Ford) by admin on 06-03-2011

download
1. Disconnect battery ground cable (14301) . 2. Remove two console armrest mounting access covers (047A62) at rear of console panel (045A36) (snaps out) to gain access to armrest retaining bolts. 3. Remove four armrest-to-floor bracket retaining bolts and remove armrest assembly (snaps out of console). 4. Remove console panel gear shift plate (044G24) (snaps out). On vehicles equipped with manual transmissions, shift boot is attached to bottom of finish panel. Remove shift knob and slide boot and console panel gear shift plate up shift lever to remove. 5. To remove top finish panel position emergency brake lever in the UP position. Remove four retaining screws and lift top finish panel up. Disconnect necessary wire connectors. 6. Remove two console-to-rear floor bracket retaining screws. 7. Insert a small screwdriver into two notches at bottom of front upper finish panel and snap out. 8. If the vehicle has a radio chassis (18806) , the radio chassis must be removed. Refer to Section 15-01. If the vehicle doesn’t have a radio chassis , use a small screwdriver and pry radio cover finish panel out of console. 9. Flex glove compartment bin tabs inward. Drop down glove compartment (06010) assembly. Remove two console-to-instrument panel retaining screws. 10. Remove four console bracket retaining screws. Remove console panel from vehicle. 11. Remove three bolts retaining steering column opening cover (3A673) and reinforcement panel. Remove cover. 12. Remove steering column opening reinforcement by removing two bolts. 13. Remove two bolts retaining steering column opening reinforcement and remove reinforcement. 14. Remove six steering column retaining nuts (two retaining the hood release mechanism and four retaining column to lower brake pedal support). Lower steering column to floor. 15. Remove upper and lower steering column shrouds (3530) and disconnect wiring from turn signal and windshield wiper switch (13K359) . 16. Remove steering column through bolt and nut on engine compartment side of cowl panel. Remove steering column from vehicle. 17. Remove brake pedal support nut. 18. Snap out instrument panel defroster opening grille (044E82) . 19. Remove screws from speaker covers. Snap out speaker covers. 20. Remove front screws retaining RH and LH scuff plates at cowl side trim panels. 21. Remove RH and LH cowl side trim panels. 22. Disconnect wiring at RH cowl side. 23. Remove cowl side retaining bolts (one each side). 24. Remove five cowl top screws attachments. 25. Gently pull instrument panel (04320) away from RH side of cowl panel. Disconnect speedometer cable, air conditioning controls and wire connectors. 26. Place a drain pan or suitable container under the heater water hose connections at the cowl panel. 27. Disconnect heater water hoses (18472) from heater core tubes and plug heater water hoses with suitable 5/8-inch and 3/4-inch plugs. Cap heater core tubes to prevent coolant loss from heater core (18476) during removal of heater case. 28. Remove screw retaining A/C evaporator case support bracket (19A639) to cowl top panel. 29. Disconnect vacuum supply supply hose (black) from A/C vacuum supply in engine compartment. 30. Working under the hood (16612) , remove nut retaining heater case to cowl panel. 31. Inside passenger compartment, remove screw retaining A/C evaporator case mounting bracket (19A865) to cowl top panel. 32. Remove one screw retaining A/C evaporator case mounting bracket below heater case to cowl panel. 33. Carefully pull heater case from cowl panel and remove heater case assembly from vehicle. 34. To install, reverse Removal procedure. Check operation of all components. 35. After repairs have been completed, check the coolant level in the radiator (8005) and in the radiator coolant recovery reservoir (8A080) . Fill as required with the recommended coolant mixture.

Related entry:

remove the rocker panel cover on 2006 altima, remove center console e39, How to remove center console cup holder in a 06 f150 super cab, how to remove overhead console on 2005 aviator youtube, 94 FORD BRONCO FRONT BUMPER REMOVAL, removing 2003 sienna instrument panel, how to remove center console 2006 Jetta, how to use bottom compartment of prius 2008, remove radio on 2007 milan, lincoln 2003 overhead console,

1993 Mitsubishi Montero TRANSFER CASE DISASSEMBLY

0

Filed Under (Mitsubishi) by admin on 30-12-2010

download
Disassembly (Ram-50) 1) Remove both 4WD indicator switches and steel balls. Remove speedometer gear assembly. Remove output shaft cover, gasket, wave spring and spacer. See Fig. 3. Remove rear cover, rear cover gasket and spacer from chain cover. Drive roll pin out of high-low shift fork. 2) Remove 2 seal plugs. Remove 2 poppet springs and steel balls. Shift transfer case to “4WD” and pull high-low shift rail out, in rear cover direction. Remove interlock plunger. Remove pulse generator (if equipped), front output shaft cover and pulse rotor (if equipped). Remove snap ring from rear bearing on output shaft. Remove chain cover, oil guide and side cover. Remove countershaft locking plate. Remove countershaft. 3) Remove countergear, 2 thrust washers, 2 needle bearings and spacer through side cover opening. Remove snap ring, spring retainers and spring from 2WD-4WD shift rail. Remove front output shaft, rear output shaft and chain as assembly. 4) Remove 2WD-4WD shift fork and distance piece. Drive out 2WD-4WD shift rail spring pin. Remove 2WD-4WD shift rail and lug. Remove high-low shift fork and high-low synchronizer sleeve. Remove needle bearing and snap ring from input gear. Remove input gear assembly. 5) If either control shaft or input gear oil seals are to be replaced, drive out roll pin from transmission control change shifter. Separate transfer case from adapter. See Fig. 3. Disassembly (Montero) 1) Remove dynamic damper, 5 detection switches and 3 steel balls. Remove poppet plug, spring and steel ball. Remove speedometer gear assembly. Remove output shaft rear cover, spacers, dust seal guard and oil seals. Front output shaft cover, wave spring and spacer (if equipped). 2) Remove high-low shift rail plug and high-low shift fork spring pin. Shift transfer case to “4WD”. Remove rear cover and high- low shift rail. Remove interlock plunger. Remove rear output shaft (viscous coupling) assembly and center differential assembly. Remove 2WD-4WD synchronizer assembly, chain and front output shaft from transmission as a unit. With White paint make match marks in grooves of 2WD-4WD synchronizer in 3 places. With White paint make match marks on spline projections of 2WD-4WD synchronizer sleeve in 3 places. Refer to match marks during reassembly. 3) Remove snap ring, spring seat, spring, 2WD-4WD shift fork and 2WD-4WD synchronizer sleeve. Remove differential lock hub, oil dam cover and bearing retainer. Remove side cover and gasket. Remove transfer counter gear shaft, transfer counter gear, thrust washer, needle bearings and spacer. Remove transfer drive shaft assembly. Remove high-low shift fork assembly and clutch sleeve. Remove transfer input gear assembly. 4) Remove 2WD-4WD shift lug spring pin, spring, spring retainer 2WD-4WD shift lug and shift rail. Remove input gear oil seal, baffle plate, dust seal guard and front output shaft oil seal. See Fig. 4.

Related entry:

how to remove a rack and pinion 2004 gmc envoy, removing the dash pad in a 2000 porsche boxster, How to replace an antenna on a S10 blazer, 1996 VW Golf Manual Shift Linkage, how to remove a visor from a subaru outback, remove gear shift knob 1996 chrysler pacifica, disconnect anti theft fuse on 1991 sadandiville diagram, f250 ashtray removal, 2006 Dodge Caravan tailgate removal, vw t4 gear lever removal,

2001 Toyota Sienna CE Trunk / Liftgate Service and Repair DISASSEMBLY

0

Filed Under (Toyota) by admin on 11-07-2010

download
1. REMOVE BACK DOOR ASSIST GRIP a. Using a screwdriver, open the covers. HINT: Tape the screwdriver tip before use. b. Remove the 2 screws and assist grip. 2. REMOVE BACK DOOR PULL STRAP a. Using a screwdriver, remove the strap cover. HINT: Tape the screwdriver tip 3. REMOVE CENTER GARNISH Using a screwdriver, remove the center garnish. HINT: Tape the screwdriver tip before use. 4. REMOVE SIDE GARNISH a. Using a screwdriver, remove the side garnish. HINT: Tape the screwdriver tip before use. b. Employ the same manner described above to the other side. 5. REMOVE DOOR TRIM BOARD a. Insert a screwdriver between the door and door trim board to pry the door trim board out. NOTE: Be careful not to damage the door and door trim board. HINT: Tape the screwdriver tip before use. b. Pull the door trim board to remove it. 6. REMOVE HIGH-MOUNTED STOP LIGHT a. Remove the 2 screws. b. Disconnect the connector. c. Remove the high-mounted stop light. 7. REMOVE WASHER NOZZLE 8. REMOVE REAR WIPER ARM Remove the nut, rear wiper arm. Torque: 5.4 N.m (55 kgf.cm, 48 in.lbf) 9. REMOVE WIPER MOTOR AND LINK ASSEMBLY a. Remove the 3 bolts from the wiper motor. b. Remove the 2 bolts and wiper motor and link assembly. Torque: 5.4 N.m (55 kgf.cm, 48 in.lbf) c. Remove the grommet. 10. REMOVE COMBINATION LIGHTS 11. REMOVE LICENSE PLATE LIGHT ASSEMBLY a. Disconnect the back door control cable from the handle lever. b. Disconnect the connector. c. Remove the 3 nuts. d. Using a screwdriver, remove the license plate light assembly. HINT: Tape the screwdriver tip before use. e. Remove the handle lever from the license plate light cover. f. Remove the license plate light assembly from the license plate light cover. 12. REMOVE KEY CYLINDER

Related entry:

chevy traverse torx screw driver, crankshaft drive belt pulley toyota sienna remove, discovery 2 a pillar removal, removing 300zx rear trim, scion xb rear hatch handle how to -tc, sienna 2000 dash board cluster replacement u tube,

1997 Ford F-250/350/Super Duty Engine Front Cover Removal

0

Filed Under (Ford) by admin on 06-03-2011

download
Crankshaft front seal replacement is recommended whenever the engine front cover (6019) has been removed. 1. Disconnect battery ground cable (14301). Drain crankcase. 2. Drain cooling system. Refer to Section 03-03. 3. Remove drive belts (8620). Refer to Section 03-05. 4. Remove bolts attaching fan shroud (8146) to radiator (8005). 5. Remove fan blade (8600) from fan clutch (8A616) and remove fan shroud. 6. Remove fan clutch and water pump pulley (8509) from water pump (8501). 7. Disconnect upper radiator hose (8260) and lower radiator hose (8286) at engine (6007). Disconnect transmission oil cooler lines at radiator. 8. Remove upper radiator support bracket and remove radiator. 9. Remove generator pivot and attaching bolts. Remove generator (GEN) (10300) from generator mounting bracket (10153) and generator adjusting arm (10145). 10. Remove two bolts attaching generator adjusting arm to water pump and generator mounting bracket and remove generator adjusting arm. 11. Remove air pump pivot and attaching bolts. Remove secondary air injection pump (AIR pump) (9A486) from generator mounting bracket. 12. Remove four bolts attaching generator mounting bracket to cylinder head (6049), cylinder blocks (6010) and water pump, and remove generator mounting bracket. 13. Remove power steering pump pulley (3A733) from power steering pump (3A674). 14. Remove power steering lines from power steering pump. Remove four bolts attaching power steering pump to A/C compressor mounting bracket (2882) and remove power steering pump from A/C compressor mounting bracket. 15. Remove four bolts attaching A/C compressor (19703) to A/C compressor mounting bracket. Remove four bolts and one nut attaching A/C compressor mounting bracket to cylinder head and water pump. Remove A/C compressor mounting bracket from engine. 16. Remove the crankshaft pulley (6312) from the crankshaft vibration damper (6316). 17. Remove bolt and washer attaching crankshaft vibration damper. Remove crankshaft vibration damper using Crankshaft Damper Remover T58P-6316-D or Rotunda Gear and Pulley Puller 014-00293 or equivalent. Remove Woodruff key and crankshaft damper spacer from crankshaft (6303).

Related entry:

how to remove hydralic coolin fan pump pully, ford contour crankshaft pulley removal, how to remove cranl pully 98 ranger 2 5, navistar 8600 service manual, remove bracket rusted to railing, torque spec for 03 cavalier brake caliper,