how to remove output shaft bearing manual transmission


You are searching repair manual in PDF format about how to remove output shaft bearing manual transmission use another keyword for search another post or files



  how to remove output shaft bearing manual transmission Direct Download speed 5787 Kb/s

  how to remove output shaft bearing manual transmission Full Version speed 6767 Kb/s




1993 Mitsubishi Montero TRANSFER CASE DISASSEMBLY

0

Filed Under (Mitsubishi) by admin on 30-12-2010

download
Disassembly (Ram-50) 1) Remove both 4WD indicator switches and steel balls. Remove speedometer gear assembly. Remove output shaft cover, gasket, wave spring and spacer. See Fig. 3. Remove rear cover, rear cover gasket and spacer from chain cover. Drive roll pin out of high-low shift fork. 2) Remove 2 seal plugs. Remove 2 poppet springs and steel balls. Shift transfer case to “4WD” and pull high-low shift rail out, in rear cover direction. Remove interlock plunger. Remove pulse generator (if equipped), front output shaft cover and pulse rotor (if equipped). Remove snap ring from rear bearing on output shaft. Remove chain cover, oil guide and side cover. Remove countershaft locking plate. Remove countershaft. 3) Remove countergear, 2 thrust washers, 2 needle bearings and spacer through side cover opening. Remove snap ring, spring retainers and spring from 2WD-4WD shift rail. Remove front output shaft, rear output shaft and chain as assembly. 4) Remove 2WD-4WD shift fork and distance piece. Drive out 2WD-4WD shift rail spring pin. Remove 2WD-4WD shift rail and lug. Remove high-low shift fork and high-low synchronizer sleeve. Remove needle bearing and snap ring from input gear. Remove input gear assembly. 5) If either control shaft or input gear oil seals are to be replaced, drive out roll pin from transmission control change shifter. Separate transfer case from adapter. See Fig. 3. Disassembly (Montero) 1) Remove dynamic damper, 5 detection switches and 3 steel balls. Remove poppet plug, spring and steel ball. Remove speedometer gear assembly. Remove output shaft rear cover, spacers, dust seal guard and oil seals. Front output shaft cover, wave spring and spacer (if equipped). 2) Remove high-low shift rail plug and high-low shift fork spring pin. Shift transfer case to “4WD”. Remove rear cover and high- low shift rail. Remove interlock plunger. Remove rear output shaft (viscous coupling) assembly and center differential assembly. Remove 2WD-4WD synchronizer assembly, chain and front output shaft from transmission as a unit. With White paint make match marks in grooves of 2WD-4WD synchronizer in 3 places. With White paint make match marks on spline projections of 2WD-4WD synchronizer sleeve in 3 places. Refer to match marks during reassembly. 3) Remove snap ring, spring seat, spring, 2WD-4WD shift fork and 2WD-4WD synchronizer sleeve. Remove differential lock hub, oil dam cover and bearing retainer. Remove side cover and gasket. Remove transfer counter gear shaft, transfer counter gear, thrust washer, needle bearings and spacer. Remove transfer drive shaft assembly. Remove high-low shift fork assembly and clutch sleeve. Remove transfer input gear assembly. 4) Remove 2WD-4WD shift lug spring pin, spring, spring retainer 2WD-4WD shift lug and shift rail. Remove input gear oil seal, baffle plate, dust seal guard and front output shaft oil seal. See Fig. 4.

Related entry:

how to remove a rack and pinion 2004 gmc envoy, 2006 Dodge Caravan tailgate removal, how to remove a visor from a subaru outback, remove gear shift knob 1996 chrysler pacifica, disconnect anti theft fuse on 1991 sadandiville diagram, vw t4 gear lever removal, f250 ashtray removal, Remove Snap ring on 2004 toureg drive shaft, How to replace an antenna on a S10 blazer, 1996 VW Golf Manual Shift Linkage,

2004 Ford F-150 Rear Axle Differential Cover Axle Shaft Oil Seal and Rear Wheel Bearing REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 28-02-2011

download
1. With the vehicle in NEUTRAL, position on a hoist. For additional information, refer to Section 100-00. 2. Remove the rear wheel and tire assembly. For additional information, refer to Section 204-00. 3. Remove the parts in the order indicated in the following illustration and table. 4. To install, reverse the removal procedure. 5. Fill the axle with the specified quantity of the specified lubricant. For additional information, refer to the Specifications in this section. Item 2: Rear Disc Brake Caliper Removal Note 1. CAUTION: Do not allow the caliper to hang from the brake hose. Provide a suitable support. Position the rear disc brake caliper aside. For additional information, refer to Section 206-00. Item 7: Differential Pinion Shaft Removal Note 1. Move the differential pinion shaft out far enough to remove the U-washers. Replace the shaft and install the lock bolt finger tight when U-washers are removed. Item 8: U-washer Removal Note 1. CAUTION: Do not damage the rubber O-rings in the axle shaft grooves. Remove the U-washers. 1. Push the axle shafts inboard. 2. Remove the U-washers. Item 10 and 11: Wheel Bearing Oil Seal and Axle Shaft Bearing Removal Note 1. CAUTION: Never remove the wheel bearing oil seal by itself. Always remove the wheel bearing oil seal and the rear wheel bearing at the same time. For the 8.8 inch rear axle, use the special tools to remove the rear wheel bearing and wheel bearing oil seal. 2. CAUTION: Never remove the wheel bearing oil seal by itself. Always remove the wheel bearing oil seal and the rear wheel bearing at the same time. For the 9.75 inch and the 10.25 inch rear axles, use the special tools to remove the rear wheel bearing and wheel bearing oil seal. Item 11: Axle Shaft Bearing Installation Note 1. For the 8.8 inch and the 9.75 inch rear axles, use the special tools to install the rear axle wheel bearing. 2. For the 10.25 inch rear axle, use the special tools shown to install the rear axle wheel bearing. Item 10: Wheel Bearing Oil Seal Installation Note 1. Use the special tools shown to install the rear wheel bearing oil seal. Item 8: U-washer Installation Note 1. CAUTION: Do not damage the rubber O-rings in the U-washer grooves. Install the U-washers. 1. Position the two U-washers on the button end of the axle shafts. 2. Pull the axle shafts outward.

Related entry:

2004 ford explorer rear differential diagram, tourch on rear wheel bearing on a 2010 chevy impala, 2008 chevy silverado cv axle nut size, 2004 ford escape rear gears, 2004 expedition right axle tube seals, saturn wheel hub torque specs, balance shaft seal for 2004 honda acccord 4 cylinder schematic, 2006 suzuki forenza front wheel drive axle diagram, how to remove rear axle shaft of mitsubishi strada triton, 2003 ford f250 front axel hub diagram,

1997 Ford Explorer/Mountaineer Transmission ASSEMBLY

0

Filed Under (Ford) by admin on 06-04-2011

download
1. Thoroughly clean the transmission case and extension housing in solvent and blow dry with compressed air. 2. Inspect the transmission case for the following: 1. Stripped bolt hole threads. 2. Gasket and mating surfaces for burrs or nicks. 3. Obstructions to vent and fluid passages. Cracks or warpage. 3. Inspect the extension housing for cracks, burrs or warpage. 4. Inspect case bearing for damage. Replace as needed. 5. Remove the case bearing. 1. Install the Bearing Cup Puller with Slide Hammer into case bearing. 2. Remove the case bearing. Use an oil stone to remove any nicks or burrs in the bearing case bore. 6. Install a new case bearing. 1. Assemble and install the Drive Handle and Bearing Installer. 2. Position new case bearing onto bearing installer tool. 7. Tap case bearing into case bearing bore. 8. Install the A4LD Holding Fixure Adapter. 1. Position the A4LD Holding Fixture Adapter on the rear of the transmission case. 2. Install the A4LD Holding Fixture Adapter bolts. 9. Attach the fixture arm of the Bench Mounted Holding Fixture to the A4LD Holding Fixture Adapter. 10. Install transmission into Bench Mounted Holding Fixture. Rotate the transmission so that the fluid pan rail is facing up. -MOUNTED HOLDING FIXTURE IS SECURE. 11. Using Shift Lever Seal Replacer, install the manual control lever shaft seal. Lubricate the manual control lever shaft seal with petroleum jelly. 12. Assemble the manual valve inner lever and parking lever actuating rod as shown. 13. Install the manual control lever shaft. 14. NOTE: Align the manual control lever shaft alignment groove with the manual control lever shaft spring pin bore in the transmission case. Install the manual control lever shaft spring pin. Tap the manual control lever shaft spring pin into the transmission case. 15. Install the manual valve inner lever and parking lever actuating rod on to the manual control lever shaft. 16. Install the manual valve inner lever nut on the manual control lever shaft and tighten. 17. Install the output shaft thrust washer (No. 11). Coat the output shaft thrust washer with petroleum jelly. 18. Install the park gear.

Related entry:

case 252 roller starter schematics, how to install tetent manual lever on 5r55e tranyy, auto magz case 252 schematics, CASE W252 SCHEMATIC, Dodge neon hard to shift manual, how to remove shift lever gear and detent in 5r55e tranny,

2003-2005 Chevrolet TrailBlazer Automatic Transmission/Torque Converter Clutch (TCC) Shudder

0

Filed Under (Chevrolet) by admin on 30-12-2010

download
Automatic Transmission/Torque Converter Clutch (TCC) Shudder, Water in Transmission (Repair Transmission and Replace Transmission Filler Tube, Level Indicator and Seal) Condition Some customers may comment on a shudder condition at approximately 64-80 km/h (40-50 mph) when the TCC engages. Cause This condition may be caused by water in the automatic transmission fluid (ATF). Water may enter the transmission by dripping from the cowl area onto the handle of the transmission fluid level indicator. Indications of water in the ATF may include: • Visible rust on the transmission fluid level indicator. • Visible water in the oil pan. • A milky white substance inside the pan area. • Spacer plate gaskets that appear to be glued to the spacer plate, valve body or case. • Rust on internal transmission iron/steel components. Correction First, repair the transmission and second, replace the transmission fill tube, seal and level indicator to prevent repeat water contamination of the ATF. Transmission Repair 1. Remove the transmission. Refer to the appropriate SI procedure. 2. Disassemble and inspect the transmission. Refer to Unit Repair Automatic Transmission – 4L60-E/4L65-E. Important: If water or coolant is found in the transmission, the following components MUST be replaced. • Replace all of the rubber type seals. • Replace all of the composition-faced clutch plate assemblies including the band. • Replace all of the nylon parts (Thrust Washers). • Replace the torque converter. • Thoroughly clean and rebuild the transmission, using new gaskets and oil filter. • Flush and flow check the transmission oil cooler using J 45096. Refer to Corporate Bulletin Number 02-07-30- 052C or newer – Automatic Transmission Oil Cooler Flush and Flow Test Essential Tool J 45096 TransFlow . Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator WITH the transmission REMOVED from vehicle. 1. Remove the transmission fluid filler tube from the transmission. 2. Replace the transmission fill tube seal, P/N 1259475. 3. Replace the transmission fill tube, P/N 15000220, following the appropriate SI Document for Transmission Installation. 4. Replace the transmission fluid level indicator, P/N 15069769 when appropriate during the transmission installation. Replace the Transmission Fluid Filler Tube, Seal and Fluid Level Indicator with the transmission in the vehicle. 1. Remove the air cleaner outlet duct. Refer to Air Cleaner Element Replacement (SI Document ID# 1364496). 2. Remove the transmission fluid level indicator from the filler tube.

Related entry:

parking paw actuator rod assembly 5r55e, 2003 trailblazer torque converter removal, high pressure transmission filter for cvt trans 07 ford freestyle, 1985 chevy silverado transaxle support brace, replacing tcc solenoid for 2002 chevy astro van, how to replace filler tube on f250 transmission, mazda 626 transmission cooler install, refill plug location for transmision on 2011 camry 4 cyl automatic, how are the coolant line ran on a 2003 santa fe, manual transmission diagram 1995 sl1,

2006 Ford Crown Victoria Automatic Transaxle/ Transmission REMOVAL

0

Filed Under (Ford) by admin on 19-02-2011

download
NOTICE: Whenever a transmission has been disassembled to install new parts, the transmission fluid cooler tubes must be cleaned and backflushed using a suitable torque converter/fluid cooler cleaner. A new Oil-To-Air (OTA) transmission fluid cooler must also be installed. When internal wear or damage has occurred in the transmission, metal particles, clutch plate material or band material may have been carried into the torque converter and fluid cooler. These contaminants are a major cause of recurring transmission concerns and must be removed from the system before the transmission is put back into service. NOTE: After the transmission is removed for a major overhaul, it is important to completely clean all transmission components, including torque converter, cooler inlet tube, main control valve body, clutches and all coasting booster valve shuttle balls after any transmission service that generates contamination. These contaminants are a major cause for recurring transmission concerns and must be removed from the system before the transmission is returned to service. The cleaning of foreign material from the direct clutch check ball is often omitted. This omission can lead to a repeat servicing of the transmission. A new Oil-To-Air (OTA) transmission fluid cooler must be installed under the following condition. For additional information, refer to Section 307-02. Evidence of broken transmission components or transmission fluid contamination found due to the following transmission or converter failure modes: Major metallic failure Multiple clutches or clutch plate failure Sufficient component wear which results in metallic contamination 1. Disconnect the battery ground cable. For additional information, refer to Section 414-01. 2. WARNING: Before servicing a vehicle equipped with a fire suppression system, depower the system by following the procedure in Section 419-03. Failure to follow the instructions may result in serious personal injury. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02. 3. NOTE: Only if transmission disassembly or replacement is required, drain the transmission fluid. For additional information, refer to Fluid Pan, Gasket and Filter in this section. Drain the transmission fluid. Loosen the transmission fluid pan bolts and allow the transmission fluid to drain. After transmission fluid has drained remove the bolts and the pan and drain the remaining transmission fluid that is in the pan. 4. Install the transmission fluid pan and the old transmission fluid pan gasket. 1. Position the transmission fluid pan gasket. 2. Position the transmission fluid pan. 5. NOTE: To maintain the initial driveshaft balance, mark the rear driveshaft yoke and the axle pinion flange so they can be installed in their original positions. Mark the rear driveshaft yoke and the axle pinion flange and remove the 4 bolts.

Related entry:

1997 chrysler sebring 2 5 automatic transmission remove, 2002 ford focus e30 automatic transmission removal, 2002 Ford Escape Transmission Removal, 2001 cougar transmission range selector, nissan replace control-valve assembly frontier automatic transmission, tranmission side pan for 2011 ford escape, eurovan transmission removal, 1997 mercury mountaineer transmission removal, how to remove a matrix transmission, how to remove a transmission on a 2002 mercury sable,