download
HINT: – The installation is in the reverse order of the removal. However, when there is a special point concerning the installation, it is indicated. – When the power back door drive unit, back door w/motor lock and battery is reconnected, the back door is locked and therefore cannot be opened. Therefore, it is necessary to unlock the back door using the door control switch or transmitter switch. 1. REMOVE BACK DOOR TRIM BOARD LH a. Using a screwdriver, disengage the 3 claws and remove the trim board. HINT: Tape the screwdriver tip before use. 2. REMOVE BACK WINDOW PANEL TRIM UPPER a. Using a screwdriver, disengage the 2 claws and 7 clips, and remove the trim upper. HINT: Tape the screwdriver tip before use. 3. REMOVE ROOF HEADLINING ASSY 4. REMOVE POWER BACK DOOR DRIVE UNIT a. Remove 2 bolts A indicated in the illustration. b. Remove the 4 bolts and drive unit. c. Disconnect the connector.5. REMOVE BACK DOOR TRIM PANEL ASSY UPPER a. Using a screwdriver, disengage the 10 clips and remove the trim panel. HINT: Tape the screwdriver tip before use. 6. REMOVE BACK DOOR TRIM PANEL ASSY a. Using a screwdriver, disengage the 8 clips and remove the trim panel. HINT: Tape the screwdriver tip before use. 7. REMOVE BACK DOOR TRIM COVER RH a. Using a screwdriver, disengage the 3 clips and remove the trim cover. HINT: Tape the screwdriver tip before use. 8. REMOVE BACK DOOR TRIM COVER LH HINT: Use the same procedures described for the RH side. 9. REMOVE BACK DOOR TRIM SPACER RH a. Remove the screw. b. Using a clip remover, disengage the claw and remove the trim spacer. 10. REMOVE BACK DOOR TRIM SPACER LH

download
Introduction The 2011 model year Camry is equipped with a direct-type Tire Pressure Warning System (TPWS). Each tire (except the spare tire) has a tire pressure warning valve/sensor that measures tire pressure data. The data is transmitted to the Tire Pressure Warning System antenna/receiver and then to the Tire Pressure Warning System ECU. During Pre-Delivery Service (PDS), the tire pressure warning valves/sensors must be activated for Japan-built vehicles by following the activation procedure in this TSB. NAP-built vehicles do not require activation, but both Japan-built and NAP-built vehicles require the TPWS to be initialized by following the initialization procedure in this TSB. Initialization Procedure NOTE Perform the following initialization procedure for BOTH NAP-built and Japan-built vehicles. 1. Cycle the ignition switch to the “IG–ON” mode and connect TIS techstream. 2. Adjust all tires (except the spare tire) to the standard tire in?ation pressure, as indicated on the Tire and Loading Information label located inside the driver’s door jamb and con?rm that the Low Tire Pressure Warning Light is OFF. NOTE To adjust tire pressure correctly when outside temperature is signi?cantly colder or warmer than shop temperature. Follow the procedures outlined in the Tire In?ation Pressure Compensation and Adjustment service bulletin (T-SB-0345-08). NOTE Adjust the tire pressure when the tires are cold. NAP-built: Remove the ID number labels that are attached to each wheel and discard.

download
1. Assemble Jack Handle and Lower Spare Tire. (a) Remove the tool bag from the storage location (Fig. 3-1 on page 3) (b) Assemble the jack handle (3) and extensions rods (1 & 2) (Fig. 1-1). (c) Insert the square end of the extension rod through the access hole in the bumper and into the lowering screw (Fig. 1-2). (d) Turn counterclockwise making sure the jack handle remains firmly fitted to the extension rods. (e) Lower the tire partially from the vehicle to a suitable height allowing access to the lowering screw. (1) Ensure the wheel is safely supported in that position to prevent the spare tire from swaying during the spare tire lock installation. 2. Spare Tire Lock Installation. (a) Install the spare tire lock assembly into the lowering screw (Fig. 2-1). (1) Line up the cross pin on the spare tire lock with the slot on the lowering screw. Press the spare tire lock in place until fully seated into the bottom of the lowering screw. (b) Assemble the key assembly onto the hooked extension rod (Fig. 2-2). (c) Insert the extension rod with key through the access hole in the rear bumper (Fig. 2-3). (d) Rotate key in the lock assembly until the lock and key patterns engage. (e) Turn the jack handle clockwise making sure that the jack handle remains firmly fitted to the extension rod raising the tire until it is stowed in its original position. 3. Installation Completion (a) Disassemble the extension rod and key. (b) Place the key into the tool bag and stow with jack in the vehicle storage area (Fig. 3-1). (c) Place the ID card, order form, customer notice card and instruction sheet in the McGard envelope. (d) Place the envelope into the glove compartment.

download
Disassembly (Ram-50) 1) Remove both 4WD indicator switches and steel balls. Remove speedometer gear assembly. Remove output shaft cover, gasket, wave spring and spacer. See Fig. 3. Remove rear cover, rear cover gasket and spacer from chain cover. Drive roll pin out of high-low shift fork. 2) Remove 2 seal plugs. Remove 2 poppet springs and steel balls. Shift transfer case to “4WD” and pull high-low shift rail out, in rear cover direction. Remove interlock plunger. Remove pulse generator (if equipped), front output shaft cover and pulse rotor (if equipped). Remove snap ring from rear bearing on output shaft. Remove chain cover, oil guide and side cover. Remove countershaft locking plate. Remove countershaft. 3) Remove countergear, 2 thrust washers, 2 needle bearings and spacer through side cover opening. Remove snap ring, spring retainers and spring from 2WD-4WD shift rail. Remove front output shaft, rear output shaft and chain as assembly. 4) Remove 2WD-4WD shift fork and distance piece. Drive out 2WD-4WD shift rail spring pin. Remove 2WD-4WD shift rail and lug. Remove high-low shift fork and high-low synchronizer sleeve. Remove needle bearing and snap ring from input gear. Remove input gear assembly. 5) If either control shaft or input gear oil seals are to be replaced, drive out roll pin from transmission control change shifter. Separate transfer case from adapter. See Fig. 3. Disassembly (Montero) 1) Remove dynamic damper, 5 detection switches and 3 steel balls. Remove poppet plug, spring and steel ball. Remove speedometer gear assembly. Remove output shaft rear cover, spacers, dust seal guard and oil seals. Front output shaft cover, wave spring and spacer (if equipped). 2) Remove high-low shift rail plug and high-low shift fork spring pin. Shift transfer case to “4WD”. Remove rear cover and high- low shift rail. Remove interlock plunger. Remove rear output shaft (viscous coupling) assembly and center differential assembly. Remove 2WD-4WD synchronizer assembly, chain and front output shaft from transmission as a unit. With White paint make match marks in grooves of 2WD-4WD synchronizer in 3 places. With White paint make match marks on spline projections of 2WD-4WD synchronizer sleeve in 3 places. Refer to match marks during reassembly. 3) Remove snap ring, spring seat, spring, 2WD-4WD shift fork and 2WD-4WD synchronizer sleeve. Remove differential lock hub, oil dam cover and bearing retainer. Remove side cover and gasket. Remove transfer counter gear shaft, transfer counter gear, thrust washer, needle bearings and spacer. Remove transfer drive shaft assembly. Remove high-low shift fork assembly and clutch sleeve. Remove transfer input gear assembly. 4) Remove 2WD-4WD shift lug spring pin, spring, spring retainer 2WD-4WD shift lug and shift rail. Remove input gear oil seal, baffle plate, dust seal guard and front output shaft oil seal. See Fig. 4.

WIRING INFORMATION: 2004 Lexus RX330 WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE
RED Ignition Harness STARTER WIRE BLUE Ignition Harness SECOND STARTER WIRE WHITE Ignition Harness IGNITION  PURPLE Ignition Harnes

download