how to replace a high mount stop light in a 2006 t


You are searching repair manual in PDF format about how to replace a high mount stop light in a 2006 t use another keyword for search another post or files




2006 Hyundai Sonata STOP LAMPS REPLACEMENT HIGH MOUNTED STOP LAMP

0

Filed Under (Hyundai) by admin on 16-05-2010

download
1. Disconnect the negative (-) battery terminal. 2. Open the trunk lid and then disconnect the connector of high mounted stop
lamp. 3. Remove the package tray. 4. Replace the bulb (A) from the package tray.
5. Installation is the reverse of removal.
2006 Hyundai Sonata V6-3.3L – Service and Repair

2006 Mazda5 BODY VIBRATION AT CRUISE SPEED

0

Filed Under (Mazda) by admin on 16-06-2011

download
DESCRIPTION Some vehicles may experience a body vibration when driving approximately 55mph. This symptom is due to the characteristics of the No. 3 & No. 4 engine mounts. Modified No. 3 & No. 4 engine mounts have been established for service only. Customers having this concern should have their vehicle repaired using the following repair procedure. REPAIR PROCEDURE IMPORTANT NOTE: • This repair should only be performed if all tires and rims are confirmed to be in balance and all suspension components are in proper working condition. • Notify customers that use of the modified mounts will reduce vibration at cruising speed but may increase vibration at idle. NOTE: Because idle vibration may increase, it is highly recommended to continue using mass production mounts for all other service concerns. 1. Verify concern. 2. Replace the No. 3 & 4 engine mounts with service parts according to the appropriate Workshop Manual section 01-10 ENGINE REMOVAL/INSTALLATION. 3. Center the new engine mounts as outlined in ENGINE MOUNT CENTERING PROCEDURE. 4. Verify repair. ENGINE MOUNT CENTERING PROCEDURE No. 1, No. 3 and No. 4 Engine Mount Adjustment 1. Warm up the engine. 2. Raise and support vehicle on a hoist. 3. Remove engine under cover. 4. Lower the vehicle until the front tires lightly touch the ground. 5. Secure the engine and transaxle using an engine jack and attachment as instructed in No.3 Engine Mount And No.4 Engine Mount Rubber Installation Note in appropriate Workshop Manual, section 01-10 MECHANICAL. 6. Remove two bolts from No. 3 engine mount bracket. REMOVE THE BOLTS 7. Lift engine using jack until No.3 engine mount is lifted slightly from vehicle body. NOTE: • Do not raise engine too much or A/C pipe damage may occur. 8. Move the engine mount rubber or engine until installation hole on the vehicle body aligns with hole in the engine mount bracket. ENGINE MOUNT BRACKET 1532c SHOWN BEFORE ALIGNING THE HOLES SHOWN AFTER ALIGNING THE HOLES 9. Lower the jack and tighten bolts on No. 3 engine mount bracket. Tightening torque: 55.0-77.3 ft-lbf (74.5-04.9 N.m) NOTE: 10. With engine supported as described in STEP 5, remove four (4) nuts and two (2) bolts from No. 4 engine mount top plate. Remove top plate. NOTE: 11. Lift engine again using jack until No.4 engine mount is lifted slightly from vehicle body. NOTE: 12. With top plate of No. 4 engine mount removed, move engine mount bottom plate or engine until all four (4) installation studs on the vehicle align with the engine mount holes. • Do not allow the engine mount bracket to be misaligned. • To access the mount, remove battery box. • Do not raise engine too much or A/C pipe damage may occur. ALIGN THE 4 STUDS IN THE PLATE HOLES 13. Place top plate back on and tighten No. 4 engine mount bracket nuts and bolts to torque indicated. Tightening torque: A.32.5-45.0 ft-lbf (44.0-61.0 N.m) B.61.1-86.7 in-lbf (6.9-9.8 N.m) TIGHTEN BOLTS IN SEQUENCE SHOWN 1532e 14. Lift engine again using jack and loosen the two bolts on the No. 1 engine mount rubber until slightly loose on the No. 1 engine mount rubber.

2005–2006 Toyota Tundra Clunk Noise at Low Speeds when Stopping or Turning

0

Filed Under (Toyota) by admin on 02-06-2011

download
Some customers of 2WD 2005 – 2007 model year Sequoia and 2005 – 2006 model year Tundra vehicles may complain about a clunk, thunk, or pop noise from the vehicle that is commonly heard when stopping, accelerating from a stop, or turning at low speeds. The source of the noise has been identi?ed as the joint between the rear transmission mount and the frame crossmember. The transmission mount has been redesigned to prevent this. Use the following repair procedure to address customer concerns. Repair Procedure 1. Place the vehicle on a lift and install ChassisEAR™ (or equivalent) on the following components to help isolate the source of the noise (see Figure 1): • On frame crossmember No. 3. • On rear transmission mount above rubber section of mount or on transmission extension housing assembly. Figure 1. 2. Test drive the vehicle and duplicate the noise. 3. With ChassisEAR™ installed, the noise should be very loud from the frame crossmember No. 3 pickup location and NOT heard on the rear transmission mount above the rubber section of the mount. Is the noise loudest when ChassisEAR™ has frame crossmember No. 3 selected? • YES — Go to step 4. • NO — This TSB does NOT apply. Continue using ChassisEAR™ to identify the source of the noise and diagnose per the Repair Manual. 4. Replace the rear transmission mount, frame crossmember No. 3, and 4 bolts retaining the transmission mount to frame crossmember No. 3. A. Place the vehicle on a lift. HINT Use a transmission jack and underhoist stand to lift and support the transmission assembly during the next 5 steps. B. Remove the 4 bolts retaining the transmission to the rear transmission mount. C. Remove the 4 bolts retaining the frame crossmember No. 3 to the frame assembly and remove the frame crossmember No. 3 assembly with rear transmission mount from the vehicle. NOTE Do NOT torque any of the bolts in steps D through F until ALL the bolts in steps D through F have been started. D. Install the NEW rear transmission mount (insulator, engine mounting rear) to the transmission extension housing using the 4 bolts. Torque: 65 N*m (660 kgf*cm, 48 ft*lbf) E. Install the NEW rear transmission mount (insulator, engine mounting rear) to the NEW frame crossmember No. 3 using the 4 NEW bolts. Torque: 30 N*m (300 kgf*cm, 22.1 ft*lbf) NOTE The torque value for these 4 bolts has been increased. Figure 5. 1 Engine Mounting Rear Insulator (P/N 12371-0F080) 2 Frame Crossmember No. 3 3 Bolt w/Washer (P/N 90119-08895) 4 Front of Vehicle

2006-2008 Chevrolet Avalanche No Movement When Transmission is Shifted to Drive or Third – Normal Operation When Shifted to Second, First or Reverse

0

Filed Under (Chevrolet) by admin on 11-01-2011

download
Models: 1982-2005 GM Passenger Cars and Light Duty Trucks 2006-2007 Buick Rainier 2006 Cadillac Escalade, Escalade ESV, Escalade EXT 2006 Chevrolet SSR 2006-2008 Chevrolet Avalanche, Colorado, Express, Silverado Classic, Silverado, Suburban, Tahoe, TrailBlazer 2006 GMC Yukon Denali, Yukon Denali XL 2006-2008 GMC Canyon, Envoy, Savana, Sierra Classic, Sierra, Yukon, Yukon XL 2006 Pontiac GTO 2006-2007 HUMMER H2 2006-2008 HUMMER H3 2006-2008 Saab 9-7X with 4L60, 4L60E, 4L65E or 4L70E Automatic Transmission (RPOs MD8, M30, M32, M33 or M70) Condition Some customers may comment that the vehicle has no movement when the transmission is shifted to DRIVE or THIRD position, but there is normal operation when it is shifted to SECOND, FIRST or REVERSE position. Cause This condition may be caused by a damaged forward sprag assembly (642). Correction When inspecting the sprag, it is important to test the sprag for proper operation by holding the outer race (644) with one hand while rotating the input sun gear (640) with the other hand. The sun gear should rotate only in the counterclockwise direction with the input sun gear facing upward. If the sprag rotates in both directions or will not rotate in either direction, the sprag elements should be inspected by removing one of the sprag reserved. retaining rings (643). Refer assembly © 2010 General Motors. All rights

Service Bulletin 2001-2006 & 2008 TRIBUTE – 3.0L, 2003-2008 MAZDA6 – 3.0L, 2002-2006 MPV 3.0L – CAMSHAFT TICKING NOIS

0

Filed Under (Mazda) by admin on 18-04-2010

download
ome vehicles equipped with a 3.0L engine may exhibit a ticking noise from the left bank cylinder head while the engine is running at normal operating temperature. Customers having this concern should have their vehicle repaired using the following repair procedure. Use the table below to select the correct repair for the applicable model

A. REPAIR PROCEDURE 2002 – 2006 MPV 3.0L: 2001 – 2006 TRIBUTE 3.0L – (built BEFORE Jan. 17, 2006): CAUTION: Before attempting a 2001-2006 Tribute repair, confirm if water pump pulley is driven by INTAKE or EXHAUST camshaft. Be sure to use correct repair procedure. The water pump on 2001-2006 Tribute vehicles built BEFORE Jan. 17, 2006 are driven by the “INTAKE” camshaft pulley. 1. Verify the water pump is driven by the INTAKE camshaft pulley. 1572g WATER PUMP DRIVEN BY INTAKE CAMSHAFT PULLEY