how to replace shift solenoid in gmc yukon


You are searching repair manual in PDF format about how to replace shift solenoid in gmc yukon use another keyword for search another post or files



  how to replace shift solenoid in gmc yukon Direct Download speed 5787 Kb/s

  how to replace shift solenoid in gmc yukon Full Version speed 6767 Kb/s




2002-2004 Isuzu Axiom A/T – Shift Lock Solenoid Replacement

0

Filed Under (Isuzu) by admin on 30-04-2011

download
TSB SB05-05-5004 Shift Lock Solenoid ISSUE DATE: MAY 2005 Affected Vehicles 2002-2004 Isuzu Axiom (UP) 1998-2004 Isuzu Rodeo (UE) and Rodeo Sport (UA) Service Information Use the following steps to remove and replace the Shift Lock Solenoid. Service Procedure 1. Access the Shift Lock Solenoid by removing the Center, Front, Rear Console Assemblies, Selector Lever Knob, and Cover Assembly. Refer to the Selector Lever section in the Service Manual. 2. Set parking brake, move Selector Lever to lowest gear, and remove the Shift Lock Cable. 3. Remove the two screws securing the Shift Lock Solenoid to the Selector Lever subassembly. Disconnect the Shift Lock Solenoid 2-pin connector. 4. Disconnect the 1-40 (Rodeo) or 1-3 (Axiom) six-pin connector and slide the female connector off bracket. Remove the Terminal Position Assurance (TPA) Lock from the connector. Locate the two blue wires in position 1 and 3 on the female connector. With appropriate tool (shown above), apply light pressure upward on the connector locking tab while gently pulling on the blue wire to release. Note :Never use force to remove a terminal from a connector. 5. Insert the two blues wires from the replacement Shift Lock Solenoid into the 1- 40 (Rodeo) or 1-3 (Axiom) female connector. It does not matter which blue wire is inserted into the 1 and 3 position. Gently tug the blue wires to make sure they are secure. NOTE :D iscard the extra 2-pin connector sub harness included with replacement Shift Lock Solenoid P/N 8-97181-068-2. 6. Reconnect the Shift Lock Solenoid 2-pin connector and reattach the two screws securing the Shift Lock Solenoid to the selector lever subassembly. 7. Reconnect the 1-40 (Rodeo) or 1-3 (Axiom) six-pin connector and slide the female connector onto the bracket. 8. Reinstall the Selector Lever Knob, Cover Assembly, Center, Front, and Rear Console Assemblies. Refer to the Selector Lever section in the Service Manual. 9. Check Shift Lock operation: a. With ignition key in “Lock” position, Selector lever should not move from “P” position. b. With ignition key in “ON” position and brake pedal depressed. Selector lever can be moved out of “P” position. c. Key can be removed only when turned to “LOCK” position and selector lever is in “P” position.

Related entry:

2002 mitsubishi eclipse testing shift solenoids, how to shift 2007 chevy impala without a key, weare is the solinod pak on my2002mercury granmarquis, how to install transmission shift solenoid buick regal ls 2000, how to change a gear shif on a f 250 2001 aut, 2006 lucern shift lock release button, location a1 tshift selnoid 2002 trailblazer, isuzu 320 2000 specifications, p0753 camry solara, 2006 buick terraza lockup control solenoid valve assembly,

2003 GMC Yukon 5.3L, Lean trouble codes P0171, P0174, P0101 and P0300 are setting

0

Filed Under (GM) by admin on 11-06-2010

download
2001 Chevrolet Suburban 1500 5.3L 2003 GMC Yukon 5.3L, FLEX, Vin Z 2003 Cadillac Escalade 6.0L, Vin N, 2003 GMC Yukon XL 1500 5.3L, FLEX, Vin USA/Canada Z 1. Check for leaking intake manifold seals around the intake ports. The intake gasket seals may be leaking around the intake ports, causing a lean condition. Many times they will leak around the bottom side of the port, making it a challenge to detect the vacuum leak. May also note lower than normal Mass Airflow (MAF) readings if the seals are leaking around the ports. 2. If leaking intake gasket seals are found, replace the gaskets with the updated part number.

Related entry:

how to fix 2005 yukon wind shield wiper pulse board, how to replace evaporator 2003 escalade, 2003 GMC Yukon Compass\TEMPERTURE FUSE, removing drivers airbag 2002 gmc yukon, p0449 gmc yukon 2007, Manuel for 1997 Yukon gmc free download, Labor cost for 2002installation front differential Yukon Donalli, rear air condition parts schematic for 03 yukon xl, installing cigarette lighter cover on yukon, installing cigarette lighter cover on 2011 yukon,

2005 GMC Yukon/ Denali XL 1500 Blower Motor Control Processor Replacement

0

Filed Under (GM) by admin on 14-10-2010

download
1. If equipped, remove the sound insulator panel. 2. Disconnect the electrical connector at the blower motor. 3. Disconnect the electrical connector (4) from the blower motor control processor (2). 4. Remove the blower motor control processor retaining screws (3) from the HVAC module (1). 5. Remove the blower motor control processor (2) from the HVAC module (1). INSTALLATION PROCEDURE 1. Install the blower motor control processor (2) to the HVAC module (1). 2. Install the blower motor control processor retaining screws. NOTE: Refer to Fastener Notice in Service Precautions. Tighten the screws to 1.6 N.m (14 lb in). 3. Connect the electrical connector (4) to the blower motor control processor (2). 4. Connect the electrical connector at the blower motor. 5. If equipped, install the sound insulator panel.

Related entry:

1998 safari astro van ac vacuum diagram, 1999 yukon denali blend actuator, 07 yukon denali 6 2l rough idel, Troubleshooting P0301 Code envoy denali, relearn procedure on 2007 gmc yukon 5 3l, gmc yukon fan contiues running, 2007 gmc yukon engine idles loud, 2005 YUKON Leaking water in fan control module and passenger front, 2004 yukon rear blower location, 2002 gmc t6500 freon capacity,

| Sierra, Silverado, Suburban, Tahoe, Yukon (VIN C/K) Service Manual | 2001 GMC Truck GMC K Sierra – 4WD

0

Filed Under (GM) by admin on 12-06-2010

download
Test Description The numbers below refer to the step numbers on the diagnostic table. 2. Allow the engine to cool before performing this test. If the sensor is at the operating temperature, the HO2S voltage will stay high or low. If the HO2S voltage stays between 300-700 mV this indicates the HO2S heater is inoperative. 3. If more than one HO2S DTC is set, this is a good indication that the HO2S fuse is open. Test all the related circuits going to all the heated oxygen sensors for a short to ground. If you cannot locate a shorted circuit, it may be necessary to disconnect each HO2S one at a time to locate a shorted sensor. 4. This step determines if an ignition positive voltage supply is available at the sensor.

Related entry:

1994 gmc sierra circuit breaker location, white gmc trouble shooting, how to reset computer on 2006 gmc sierra, location of fuse boxes in 1993 GMC K series pickups, diagram of evap system for 2007 gmc sierra, wher is the evaporator drain located on 2000 GMC sierra, 03 gmc sierra code p1626, where is the 2000 gmc sierra evaporator, how to unclog ac drain on 2001 yukon xl, how to replace cv axle in 2008 gmc sierra,

2002 GMC Yukon Denali HANDLE BEZEL REPLACEMENT – INSIDE Removal Procedure

0

Filed Under (GM) by admin on 30-05-2010

download
1. Insert a flat-bladed tool between the door handle bezel and the trim panel in order to release the handle bezel tab retainers. Fig. 42: Inside Handle Bezel 2. Remove the door handle bezel from the door panel. Installation Procedure Fig. 43: Inside Handle Bezel 2. Install the door handle bezel to the door panel by pressing the bezel into place until the bezel is completely seated. ARMREST REPLACEMENT Removal Procedure 1. Remove the door trim panel. Refer to Trim Panel Replacement – Side Front Door . 2. Remove the armrest retaining screws. 3. Remove the armrest from the panel. Installation Procedure

Related entry:

2001 gmc safari dash grab handle, 2001 gmc safari dash grab handle replacement,