how to replace thermostat on a 2004 toyota matrix
You are searching repair manual in PDF format about how to replace thermostat on a 2004 toyota matrix use another keyword for search another post or files
how to replace thermostat on a 2004 toyota matrix Direct Download speed 5787 Kb/s
how to replace thermostat on a 2004 toyota matrix Full Version speed 6767 Kb/s
Filed Under (Toyota) by admin on 16-04-2010
Removing the stock air inlet system
a) Before removing any of the O.E. components, label each individual part so that no components become mixed up during the installation process. There are two Vacuum Switching Valves (VSV), and one air flow meter that have electrical and/or vacuum connections going to them. Be sure to label these connections before disconnecting them.
Remove b) Remove the two nuts and two plastic rivets that hold the plastic engine cover on. The
plastic rivets may be gently lifted with a small screwdriver. Remove the cover. c) Remove the bolt in the radiator support that holds the battery bracket. Unhook the rod at the rear of the battery bracket. Remove the battery from the vehicle
Filed Under (Audi) by admin on 15-09-2009
Check the following wire connection for open circuit according to wiring diagram:Relay carrier in E-box, plenum chamber, position 3Terminal Harness connector atignition coils Terminal 8 1 Specified value: Wire resistance max 1.5 – If necessary, repair wire connection. Audi A4 Sedan 2002-2004, Audi A4 Avant 2002-2004, Audi A4 Cabriolet 2003-2004 – 1.8 Liter 4-Cyl. 5V Turbo Generic Scan Tool, Engi…Page 5 24-158 If no malfunctions are found in wires: – Check voltage supply of Motronic Engine Control Module (ECM) voltage supply relay – J271 – Page 24-158 . – Check activation of Motronic Engine Control
Module (ECM) voltage supply relay – J271 – Page 24-159 . Checking voltage supply If specified value is not obtained:
- Connect multimeter for voltage measurement as follows. Relay carrier in E-box, plenum chamber, position 3
Filed Under (Ford) by admin on 11-05-2010
Some 1999-2004 Navigator, 2002-2003 Blackwood, 2003-2005 Aviator, 2003-2004 Marauder and 2003-2004 Mustang vehicles built before 12/19/2004 equipped with 4.6L 4V/5.4 4V engine may exhibit a runs rough, lacks power, and engine misfire, prompted by a MIL light and DTC codes P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, and P0316. ACTION Diagnose engine for engine misfire concern. If diagnostics determine an engine misfire which is characterized by leakage through exhaust valve(s), only replace the affected cylinder head(s). SERVICE PROCEDURE
Filed Under (Pontiac) by admin on 10-09-2010
1. If equipped with an automatic transmission, remove the exhaust manifold. 2. Drain the cooling system. 3. Remove the thermostat housing to water pump feed pipe bolts. 4. Remove the thermostat housing to water pump feed pipe. 5. Remove the thermostat. 2004 Pontiac Sunfire L4-2.2L VIN F Installation Procedure 1. Install the thermostat. 2. Install the thermostat housing to water pump feed pipe. Notice: Refer to Fastener Notice in Service Precautions. 3. Install the thermostat housing to water pump feed pipe bolt. ^ Tighten the thermostat housing to water pump feed pipe bolt to 10 Nm (18 inch lbs.). 4. If equipped with an automatic transmission, install the exhaust manifold. 5. Fill the cooling system.
Filed Under (Toyota) by admin on 04-06-2010
Some customers may experience a water leak at the front floor area. Water may be Introduction entering the body due to a body sealer void on the engine compartment rear wall, near the upper door hinge. Repair 1. Raise the vehicle. On the side of the vehicle that has the water leak, remove the front Procedure wheel and the front fender plastic liner. 2. Examine (with flash light and mirror) the body sealer condition on the engine compartment rear wall, near the upper door hinge. Also examine the sealer condition inside the inner fender box frame structure with access holes (see illustration).