how to reset saturn security system


You are searching repair manual in PDF format about how to reset saturn security system use another keyword for search another post or files



  how to reset saturn security system Direct Download speed 5787 Kb/s

  how to reset saturn security system Full Version speed 6767 Kb/s




1997-2000 CHEVROLET CORVETTE Maintenance Reminder Lights RESET PROCEDURES

0

Filed Under (Chevrolet) by admin on 06-10-2010

download
INTRODUCTION Some models may be equipped with one or more resettable maintenance reminder lights indicating service is required. Once services are performed, resetting of lights may be required. Information is provided to reset these lights where applicable. Most vehicles are equipped with a computer malfunction indicator light. If light comes on and remains on while driving, the vehicle requires service. After repairing fault(s) and clearing fault code(s), the malfunction indicator light should go out. Some models may use a dual-function indicator light, which is also used to indicate emission component service is due. After performing required service, reset indicator light. RESET PROCEDURES (CADILLAC) NOTE: 1980 CADILLAC 1. Every 15,000 miles, a reminder flag appears in speedometer face, indicating service of oxygen sensor is necessary. Inspect and service oxygen sensor as necessary, and reset flag. 2. To reset flag, remove lower steering column cover. Sensor reset cable is located to the left of the speedometer cluster. Pull cable lightly (maximum 2 lbs. force). Reinstall lower steering column cover. 1989-93 ALLANTE Engine Data Display 1. An OIL LIFE INDEX is one of the displays on Driver Information Center (DIC). It will display remaining oil life as a percentage estimate of the useful life of oil. 2. It will show 100 percent when the system is reset. When the oil life is 0 percent, the display will show CHANGE ENGINE OIL. After changing oil, reset oil life display. 3. To reset service reminder on 1989 models, press RANGE button until OIL LIFE INDEX appears on display. Depress and hold in AVG ECON and RANGE buttons for more than 5 seconds or until 100 is displayed. This will reset remaining oil life to 100 percent. 4. On 1990-93 models, press RANGE button until OIL LIFE INDEX appears on DIC display. Depress and hold in AVG SPEED and RANGE buttons for more than 5 seconds or until 100 is displayed. This will reset remaining oil life to 100 percent. 1989-91 ELDORADO & SEVILLE Most General Motors 1981-88 vehicles do not use a Service Reminder Indicator (SRI).

Related entry:

vw tcm reset, modified ecm for 2003 miata, reset run flat indicator ml320, dpd button on isuzu not working, Radio Reset procedure for 2005 KIA, remove service reminder from isuzu dmax, reset 2002 sebring radio, reset run flat indicator cls, reset saturn security system, saturn 2002 new starter or security passlock,

Citroen and Peugeot Reset Adaptions Bosch EDC16

0

Filed Under (Peugeot) by admin on 23-05-2010

download
The purpose of the Reset Adaptions function is to reset the base values stored in the CM’s memory to a zero state. These base values vary according to the age of the engine and the purpose of them is to maintain a perfectly adjusted engine system. After a reset the CM will re-learn the values, either automatically or by the technician performing a number of steps. The function should be used when important components have been replaced. If the base values are not reset the engine will experience stalling and hesitation problems. The process for Reset Adaptions varies from CM to CM. The technician may have to go through several steps to successfully complete the reset and re-learn procedure. On systems which require a diagnostic command the scan tool will attempt to guide the technician through these steps, but due to battery voltage dips during engine cranking the scan tool may reset before a procedure has been completed.

Related entry:

belingo reset aftechanging battery, berlingo ecu reset, citroen berlingo 1 4 ecu relay reset,

2002 Saturn SL2 A/T – 2nd to 3rd Gear Shift Flare

0

Filed Under (Saturn) by admin on 01-10-2010

download
Automatic Transaxle 2-3 Shift Flare During First Minutes of Driving After Cold Soak (Perform Bulletin Procedure) Models: 2002 Saturn S-Series Vehicles with Automatic Transaxle (RPOs MP6, MP7) Attention: General Manager, Fixed Operations Manager, Parts Manager, Technician Condition: Some customers of 2002 S-series vehicles with MP6 or MP7 automatic transaxles may comment on a 2-3 shift flare during the first few minutes of driving after vehicle cold soak. Cause: This condition may be caused by improper pressure, a leak in the 2nd clutch circuit, improper clutch plate finish on 2nd and 3rd clutches, a restriction in the 3rd clutch oil delivery path in the end cover, or improper surface finish in the piston bores of the 2-3 clutch housing. Correction: To correct this condition, duplicate by cold soaking the vehicle the amount of time at temperature described by the owner. Refer to procedure in this bulletin. Service Procedure Verify proper transaxle pressures by installing gauge and performing stepped pressure test after cold soak. Refer to “Stepped Pressure Test” procedure in the 2002 Saturn S-Series Automatic Transaxle Service Manual. ^ If pressures are low, follow the diagnostic chart for DTC P0745 for possible causes of low pressure. Refer to “P0745 – PC Solenoid Pressure Low” diagnostic in the 2002 Saturn S-Series Automatic Transaxle Service Manual. ^ If pressures are within normal ranges, proceed to Step 2. Remove the transaxle end cover. Refer to “End Cover Replacement” in the 2002 Saturn S-Series Automatic Transaxle Service Manual. Check torque on input shaft nut and end cover 3rd clutch oil passage for restrictions. ^ Input shaft nut torque should be 150 N.m (111 ft-lb). If nut is found to be loose, remove nut, clean threads and install new nut using Service Manual procedures and proceed to check 3rd oil passage. ^ Check 3rd oil passage in the end cover by pouring transaxle fluid through it and another passage. If the passage is restricted, you will notice significantly less fluid flow through it. If 3rd clutch passage is found to be restricted, install new end cover per Service Manual procedures and retest for concern. ^ If nut and 3rd clutch passage are okay, proceed to Step 4. Remove transaxle from vehicle. Refer to “Transaxle Removal” in the 2002 Saturn S-Series Automatic Transaxle Service Manual. Disassemble transaxle and install new 2-3 clutch housing, clutch pistons and clutch plates. Refer to “Transaxle Disassemble” in the 2002 Saturn S-Series Automatic Transaxle Service Manual.

Related entry:

2002 saturn l100 manuals, where are the grease nipples on a 2002 suzuki XL7?, 2002 saturn l 200 manual transmission shifter and linkage diagram, saturn sc2 thermostat replacement 2002, Saturn Axle Nut Torque Specs, how to remove the battery from a saturn lw 200, leaking transaxel 2002 ford escape, manual shift assembly for 2002 saturn l200, how to reset sunroof on saturn suv, pir manuls 2002 saturn S-series,

IMMOBILIZER KEY CODE RESET 4Runner, Camry, Highlander, Land Cruiser, MR2 Spyder, RAV4, Sequoia, & Solara

0

Filed Under (Toyota) by admin on 22-04-2010

download
Introduction Immobilizer Reset is a new feature that allows the registration of a new Master Key even if all original Master Keys are lost. Once the Immobilizer system is reset, all previously registered keys will be erased.Function
The Immobilizer Reset function is a 5-step process: Description 1. Using the Diagnostic Tester, retrieve a “Seed Number” through the OBD/MOBD Immobilizer function. S A “Seed Number” is a unique number provided by the Diagnostic Tester and validated by TIS in order to return a Passcode. 2. Using TIS, select Immobilizer Reset, and complete the request form to retrieve a “Passcode Number.”
S A “Passcode Number” is a unique number required by the Diagnostic Tester to reset the ECU allowing it to accept a new Master Key. 3. Enter the “Passcode Number” received from TIS into the Diagnostic Tester. 4. Confirm successful Immobilizer reset and new Master Key registration. 5. Register any additional customer keys.

Related entry:

how to reset the theft inmobilizer in a nissan, 2005 mazda 3 immobilizer reset, secret switch to turn off toyota MR2 1992 imbolizer, immobilizer malfunction, How to Reset bmw Immobilizer System, bmw z3 vehicle immobilizer, bmw immobilizer manaul pdf, 350z immobilizer issues, 2007 bmw 540i imobilizer, toyota 2kd immobiliser bypass,

2007 Honda Odyssey Resetting the PAX System Warning

0

Filed Under (Honda) by admin on 30-07-2010

download
Resetting the PAX System Warning When a tire goes flat or, is very low on pressure, the multi-information display will show “PAX SYSTEM WARNING, RUN FLAT DRIVING.” After the tire is repaired or replaced, you must reset the warning indicator (and the mileage counter that supports it), no matter how far the vehicle was driven in the run flat mode. 1. To put the gauge control module into the self-diagnostic mode: Turn the headlight switch to ON. Press and hold the SELECT/RESET (instrument panel brightness) knob. Turn the ignition switch to ON (II). Within 5 seconds, turn the headlights to AUTO, then to ON, and then to AUTO again. Within 5 seconds, release the SELECT/RESET knob, then push and release the knob three times. 2. Once the gauge control module is in the self-diagnostic mode, press and hold the INFO button on the steering wheel for 5 seconds to get to the CUSTOMIZE MENU. 3. Use the INFO button to scroll through to the PAX RESET screen, then press the SEL/RESET button on the steering wheel. 4. Use the INFO button to scroll to the appropriate wheel, and then press the SEL/RESET button on the steering wheel to reset the PAX warning system display. The screen should read PAX RESET COMPLETED. Repeat this step for each wheel that needs to be reset. 5. Use the INFO button to scroll through to EXIT, then press the SEL/RESET button. 6. Turn the ignition switch to LOCK (0) to exit the self-diagnostic mode.