Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
NOTE: Both pulse generator-B inspection and TCM reprogramming procedures should be performed. PULSE GENERATOR-B INSPECTION PROCEDURE: 1. Open and secure the hood. 2. Remove the resonator. 3. Locate the pulse generator under the battery tray. Disconnect the pulse generator connector (blue) and remove the pulse generator male connector (black) from the bracket. 2001 Hyundai Accent GS Sedan L4-1.6L 4. Using an ohmmeter, check the resistance between terminal No. 3 and No. 4 in the disconnected pulse generator male connector (black color). Resistance value: 215-275W (at 20°C or 68°F) If the resistance is lower or higher than the specification, replace the pulse generator (P/N 45955-22700). If the resistance is within specification go to Step 5. 5. Clean both ends of the disconnected pulse generator connectors with aerosol electrical contact cleaner. 6. Apply contact grease (P/N 00305-F0000-39, NYOGEL 760G), into all four terminal openings of the blue female connector until each terminal opening is completely filled with grease. 7. Reconnect the pulse generator connectors and reattach the connector to the bracket. Reinstall all removed components in the reverse order of removal. TCM SPECIFICATIONS CAUTIONS BEFORE REPROGRAMMING:

download
1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip and remove the trim panel surrounding the radio and includ- ing the a/c vents. (Figure A) 3 Remove (4) Phillips screws securing the radio. (Figure B) 4 Disconnect and remove radio. (Figure B) Continue to KIT ASSEMBLY. 1 KIA RIO: Cut and remove shaded areas #1. (Figure A) HYUNDAI ACCENT: Cut and remove shaded areas #2. (Figure A) 2 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. (Figure B) 3 Slide the aftermarket head unit into the cage until secure. (Figure C) Continue to final assembly.

Workshop Manual & Electronic Troubleshooting Manual 2005-2006
Hyundai Accent, Elantra, Tucson, Santa Fe, Sonata, Azera, Tiberon
Table of Content

download
While installing the tube and hose assembly, be sure to align white marks on each fitting. Pressure Hose and Tube 1. Remove the air intake hose assembly. 2. Detach the pressure hose mounting clamp. 3. Disconnect the pressure tube fitting at the gear box side. 2000 Hyundai Elantra GLS Wagon L4-2.0L 4. Lift up the vehicle and detach the mounting clamp which is holding both the pressure tube and the return tube. 5. Lift down the vehicle and remove the connector (24 mm). 6. Remove the pressure hose and tube assembly. 7. Installation is the reverse order of removal. NOTE: 1. Install the pressure hose and tube so that they are not twisted and they do not come in contact with any other parts. 2. After installation, bleed the system. Return Tube and Hose 1. Detach the power steering fluid reservoir from its mounting bracket. 2. Remove the engine coolant reservoir. 2000 Hyundai Elantra GLS Wagon L4-2.0L 3. Detach the return tube and hose assembly mounting clamps. 4. Remove the air intake hose assembly. 5. Disconnect the pressure tube and the return tube fittings at the gear box side. 6. Lift up the vehicle and detach the mounting clamp which is holding both the pressure tube and the return tube. 7. Lift down the vehicle and disconnect the clamp holding the return tube & hose assembly (G) and (C). 2000 Hyundai Elantra GLS Wagon L4-2.0L 8. Remove the return tube & hose assembly (G). 9. Detach the air conditioning discharge hose mounting clamp. 10. Disconnect the clamp holding the return tube & hose assembly (C) and the oil cooler tube. 11. Remove the return tube & hose assembly (C). 12. Installation is the reverse order of removal. NOTE: 1. Install the return tube and hose assembly so that it is not twisted and it does not come in contact with any other parts. 2. After installation, bleed the system. Oil Cooler Tube 1. Remove the front bumper and rail assembly. (Refer to Body and Frame.) 2. Disconnect the connection of the oil cooler tube from the return tube. 3. Disconnect the connection of the coil cooler tube from the return hose of the fluid reservoir.

download
Turn ignition off. Apply battery voltage to fuel pump check connector terminal. See Fig. 1 . Remove fuel tank cap and listen for fuel pump operation. Pinch fuel hoses by hand, and ensure fuel pressure can be felt. Fig. 1: Locating Fuel Pump Check Terminal (Accent Shown; Other Models Are Similar) FUEL PRESSURE TEST Accent & Elantra 1. Release fuel pressure. See FUEL PRESSURE RELEASE . Disconnect high-pressure fuel hose from fuel delivery pipe. Cover hose connection using rags to avoid spraying of fuel.