hyundai tucson 2009


You are searching repair manual in PDF format about hyundai tucson 2009 use another keyword for search another post or files




1996-2000 Hyundai Accent/ Hyundai Pony/ Hyundai Excel Trouble code identification

0

Filed Under (Hyundai) by admin on 07-06-2010

download
Idle air control (IAC) valve – circuit malfunction Wiring, IAC valve, ECM Injector 2 or 3 – circuit malfunction Wiring, injector Mass air flow (MAF) sensor – circuit malfunction Wiring, MAF sensor, ECM Idle air control (IAC) valve – circuit malfunction Wiring, IAC valve, ECM Wiring, HO2S, mechanical fault, fuel system, fuel Heated oxygen sensor (HO2S) – malfunction pressure, ECM AC cooling fan – circuit malfunction Wiring, AC cooling fan Idle air control (IAC) valve – circuit malfunction Wiring, IAC valve, ECM Engine coolant temperature (ECT) sensor – circuit malfunction Wiring, ECT sensor, ECM Intake air temperature (IAT) sensor – circuit malfunction Wiring, IAT sensor, ECM

2008-2009 Pontiac G6 GXP 2008-2009 Pontiac G8 2008-2009 Pontiac Torrent GXP Intake System Throttle Body Spacer installation

0

Filed Under (Pontiac) by admin on 17-08-2010

download
Installation Instructions Part Number 200-630 2008-09 Buick Enclave 2008-09 Chevrolet Equinox Sp. 2008-09 Chevrolet Malibu 2008-09 Chevrolet Traverse 2008-09 GMC Acadia 2008-09 Pontiac G6 GXP 2008-09 Pontiac G8 2008-09 Pontiac Torrent GXP 2008-09 Saturn Outlook 2008-09 Saturn Vue XR 2008-09 Suzuki LX7 3.6L V-6 2. Disconnect the breather hose elbow from the intake tube. Loosen the two hose clamps that secure the intake tube to the throttlebody, and the mass air flow sensor. Remove the air intake tube. 1. Disconnect the negative battery cable! Remove the oil fill cap and set it aside. Lift straight up on the engine beauty cover and set it aside. Reinstall the oil fill cap after the beauty cover has been re- moved to prevent any foreign material from entering the crank- case. 3. Remove the four bolts that secure the throttlebody to the in- take manifold. 5. Install the provided bolts and washers thru the throttlebody and Poweraid Spacer and tighten to the manufacturer’s specifi- cations. 4. Install the Poweraid Spacer between the throttlebody and the intake manifold with the first supplied gasket next to the intake manifold, and the second supplied gasket next to the throttle- body as shown. Make sure the “flow” arrow printed on the spacer is pointing towards the intake manifold. 6. Reinstall the intake tube, tighten the two hose clamps, and reconnect the crankcase breather tube. Reinstall the beauty cover, and oil cap in the reverse order that they were removed. Re-connect the negative battery cable!

2008-2009 GMC Canyon, GMC Envoy 2008-2009 Saab 9-7X Engine Runs Rough (Inspect for Water Intrusion in Spark Plug Recess Area, Replace Spark Plug and Ignition Coil, Seal Ignition Coil Bolt Hole Vents and Seal Hood Air Grille)

0

Filed Under (GM) by admin on 04-06-2010

download
Models: 2008-2009 Chevrolet Colorado, TrailBlazer 2008-2009 GMC Canyon, Envoy 2008-2009 HUMMER H3, H3T 2008-2009 Saab 9-7X All Equipped With Engine RPOs LLR, LLV, LL8 Please Refer to GMVIS Condition Some customers may comment that the malfunction indicator lamp (MIL) is illuminated. Some customers may also comment that the engine runs rough. The technician may find DTCs P0300, P0301, P0302, P0303, P0304, P0305, or P0306 set as current or in history, depending on which engine the vehicle is equipped with. Upon further examination, the technician may observe evidence of water intrusion into the spark plug recess area. Cause This condition may be caused by an engine being exposed to a large quantity of water, which may result in some of the water seeping down past the vented threads of an ignition coil bolt, then flowing through the vent opening that is located in the bottom of the related ignition coil bolt hole, and collecting in the spark plug recess area. Correction Important: DO NOT reprogram or replace the engine control module (ECM) for this condition. If evidence of water intrusion in the spark plug recess area/s is not observed, then refer to the appropriate DTC procedures in SI.

2004 Hyundai Sonata 2003-2004 Hyundai Santa FE 2004 Kia Optima no spark Problem and Repair

0

Filed Under (Hyundai) by admin on 25-04-2010

download
1. At the crank position sensor, check for battery voltage to be present on the Red wire with the key on and cranking. The Black wire should be a good ground and the Blue wire should have 5 volts on it from the computer. One may have to disconnect the crank sensor to check for the 5 volt reference. 2. During crank look for a good 5 volt square wave signal on the Blue wire. 3. Check at the ignition coils for good battery voltage key on and cranking. If there is a loss of voltage during crank check the ignition failsafe relay. 4. Check for any stored engine codes. Crankshaft Position (CKP) Sensor Ignition Failsafe Sensor The ignition failsafe sensor supplies battery voltage to the ignition coils. The ignition coils can look like they have good battery voltage key on but during crank the ignition failsafe relay can stop sending voltage to the ignition coils.

Installation Manual TWM Performance Shifter Cable Bushing Kit 2001-2006 Hyundai Elantra 2003+ Hyundai Tiburon

0

Filed Under (Hyundai) by admin on 06-04-2010

download
1. Working in the engine bay, use a Phillips head screwdriver to remove the 2 screws over the driver’s side headlight and a 10mm
socket with a ratchet and an extension to remove the 10mm bolt holding the splash guard. Remove the splash guard from the engine bay. Loosen the 10mm bolt (shown by the top arrow) holding the top part of the air box to the throttle body inlet and unclip
the 2 clips holding this part of the air box to the bottom part (also shown by two arrows). Remove the top part of the air box and the
air filter as well. 2. Remove the three 10mm bolts at the bottom of the air box using the socket and ratchet with extension. Remove the bottom part of the air box from the engine bay.