isuzu 4jg2 codes


You are searching repair manual in PDF format about isuzu 4jg2 codes use another keyword for search another post or files



  isuzu 4jg2 codes Direct Download speed 5787 Kb/s

  isuzu 4jg2 codes Full Version speed 6767 Kb/s




1995 Ford Thunderbird Antilock Brakes / Traction Control Systems: Testing and Inspection Displaying and Reading Trouble Codes

0

Filed Under (Ford) by admin on 14-08-2010

download
NOTE: Ford DOES NOT provide procedures to retrieve or clear trouble codes without the Super Star II tester. The anti-lock brake/traction assist system has on-board diagnostic capabilities. However, the module as received from manufacturing is equipped with a stored error code (61). This will affect the service procedure. The error codes can be retrieved from the ABS module in the following manner. 1. 2. 3. 4. Connect Super STAR II tester to connector located in engine compartment on the power distribution box. Turn on Super STAR II tester and latch button down in TEST position. Turn ignition switch to RUN position. Read first code output. After approximately 15 seconds, the next code will be output. Leave button latched until all codes are output. NOTE: Make sure that all codes are written down. 5. The diagnostic procedure should be as follows provided that the CHECK ANTI-LOCK BRAKE indicator stays on all the time or flashes intermittently. NOTE: If the BRAKE warning indicator is on or intermittently comes on, refer to the Warning Indicator Symptom Chart. NOTE: If there are more codes stored in the anti-lock brake control module memory, no codes will erase until all codes have been output by the Super STAR II tester, all malfunctions have been serviced and the vehicle is driven about 40 km/h (25 mph). This means that if a 20s code originally existed and was serviced, it can be ignored when running the on-board diagnostic the second time. If the first code received is 18, 19 or in the 20s and no other code is received, service the indicated component. No other codes can be output if a 20s code exists. After servicing the indicated 18, 19, or 20s code, repeat the procedure for retrieving error codes. 6. If a code 61 is received with any other code, ignore the code 61 and service the other indicated components. If, after correcting all other indicated malfunctions, the CHECK ANTI-LOCK BRAKE indicator is still on, service the Fluid Level Switch (FLS) circuit. 7. If a code 61 is received and no other codes are received, service the FLS circuit. 8. If no code, or only a code 10 is received, use the Anti-Lock Quick Check Sheet since some possibilities are not recognized and retained in the anti-lock brake control module memory. See: Trouble Code Descriptions/Quick Check Sheet 9. When dealing with intermittent ABS warning light ON concern, make certain to visually inspect all wiring related to the component associated with the code received.

Related entry:

International Trouble Code Chart, 02 liconl town car code b 1681, 2010 Sprinter Trouble Codes, what is ford dtc b1681, 1990 ford ranger codes, international esc codes, list of vehicle codes for 2003 jeep liberty, p1150 lexus rx300, fault code P1442, 1997 international trouble codes,

2001-2005 Hyundai XG300/ 350, Hyundai SANTA FE 3.5L ELECTRONIC THROTTLE SYSTEM (ETS) DIAGNOSTIC TROUBLE CODES (DTC) UPDATE

0

Filed Under (Hyundai) by admin on 03-06-2010

download
This bulletin supersedes TSB# 05-36-004 to correct the reference number of the TSB for throttle initialization procedure. DESCRIPTION: The 2001-2005 MY XG300/350 and Santa Fe 3.5L incorporate an Electronic Throttle control System (ETS). NOTE: Please see TSB 05-36-002 for a general description of the system, its components and the INITIALIZATION procedure. The list of DTC codes has been modified. This TSB lists and explains the updated Diagnostic Trouble Codes (DTC) related to the ETS system. NOTE: Some diagnostic trouble codes (DTCs) for 2004-2005 MY Santa Fe 3.5L and 2004-2005 XG350 vehicles have been added and revised. TSB 04-36-013 provides the newly added and revised DTCs in addition to the diagnostic procedures for these DTCs.

Related entry:

p0420 for a 2006 pacifica, remove domelight in 2001 hyundai xg300, location of crankshaft position sensor 2003 v6 3 5l hyundai santa fe, how to show fault codes on hyundai Santafe 2010, Hyundai 2 0T Idle Relearn, hyundai santa fe mil light, hyundai santa fe p401, hyundai trajet location of p0120 trouble code, jeep liberty code 3008, 04 malibu maxx trouble codes,

1996-2000 Chevrolet Express Van Information on Error Codes on Radio Display – Their Cause and Corrective Action

0

Filed Under (Chevrolet) by admin on 17-12-2010

download
Starting in 1995, the family style radios, as well as the 12-disc LLAI and 6-disc LLAI (Low Level Audio Interface) changers and the 10-disc FMI (FM Interface) changers, have error codes to help diagnose playback mediums. Some systems will only have an ERR message and no other indicator. If an ERR message is encountered without any other identifier, you may review the following error codes to try to determine the cause of the error and correct it before sending the unit to the authorized service center. If ERR or E (and a number) appears on a customer’s radio display, the number may give you a clue to the problem and corrective action. Below is a list of code numbers that may appear on the unit. Important: Not all family radios have these codes. They are dependent on the model year. Cassette Errors • E10 or TIGHT TAPE: Tight tape error Cause(s): A restricted cassette tape transport or broken cassette drive belt Correction: Substitute a different cassette tape. If there still is an error code, service the unit at an ACDelco® Service Center. • E11 or BROKEN TAPE: Broken Tape Error Cause(s): A broken cassette tape Correction(s): Substitute a different cassette tape • E12 : Communication Error

Related entry:

Peugeot 308 fault codes, berlingo radio display, edc03781, fault code P1340 on a peugeot 308, peugeot navigation system error messages,

2000 Isuzu VehiCROSS Timing Belt: Service and Repair Removal Installation

0

Filed Under (Isuzu) by admin on 21-09-2010

download
Removal 1. Disconnect battery ground cable. 2. Remove air cleaner assembly. 3. Remove radiator upper fan shroud from radiator. 4. Move drive belt tensioner to loose side using wrench then remove drive belt. 5. 6. 7. 8. 9. 10. 11. 12. Remove cooling fan assembly four nuts, then the cooling fan assembly. Remove cooling fan drive pulley assembly. Remove idle pulley assembly. Remove serpentine belt tensioner assembly. Remove power steering pump assembly. Remove crankshaft pulley assembly using J-8614-01 crankshaft holder, hold crankshaft pulley remove center bolt, then the pulley. Remove right side timing belt cover then left side timing belt cover. Remove lower timing belt cover 2000 Isuzu Truck VehiCROSS (4WD) V6-3.5L  13. Remove pusher. Caution: The pusher prevents air from entering the oil chamber. Its rod must always be facing upward. 14. Remove timing belt. Caution: 1. Do not bend or twist the belt. otherwise its core could be damaged. The belt should not be bent at a radius less than 30 mm. 2. Do not allow oil or other chemical substances to come in contact with the belt. They will shorten the life. 3. Do not attempt pry or stretch the belt with a screw driver or any other tool during installation. 4. Store timing belt in a cool and dark place. Never expose the belt to direct sunlight or heat. Installation Note: For correct belt installation, the leper on the belt must be able to be read as viewed from the front of the vehicle. 2000 Isuzu Truck VehiCROSS (4WD) V6-3.5L  1. Install timing belt. 1. Align groove of crankshaft timing pulley with mark on oil pump. Align the mark on the crankshaft timing pulley with alignment mark (white dots line) on the timing belt. Secure the belt with a double clip. Note: When timing marks are aligned, No.2 piston will be on top Dead Center.

Related entry:

2000 izsu ftr wirin diagram, repair on isuzu 320 frontier 1998 front suspension, 1989 Isuzu NPR truck service manuals, isuzu rodeo 95 alternator belt diagram, ISUZU NPR CODE 17, isuzu 6HE1 shopmanual, isuzu 4ze1 oil pump install, isuzu 4hj1 repair manual, front crank pulley torque isuzu 4JJ1, 89 isuzu pick up can the clutch release lever come off the ball stud?,

2002-2004 Isuzu Axiom A/T – Shift Lock Solenoid Replacement

0

Filed Under (Isuzu) by admin on 30-04-2011

download
TSB SB05-05-5004 Shift Lock Solenoid ISSUE DATE: MAY 2005 Affected Vehicles 2002-2004 Isuzu Axiom (UP) 1998-2004 Isuzu Rodeo (UE) and Rodeo Sport (UA) Service Information Use the following steps to remove and replace the Shift Lock Solenoid. Service Procedure 1. Access the Shift Lock Solenoid by removing the Center, Front, Rear Console Assemblies, Selector Lever Knob, and Cover Assembly. Refer to the Selector Lever section in the Service Manual. 2. Set parking brake, move Selector Lever to lowest gear, and remove the Shift Lock Cable. 3. Remove the two screws securing the Shift Lock Solenoid to the Selector Lever subassembly. Disconnect the Shift Lock Solenoid 2-pin connector. 4. Disconnect the 1-40 (Rodeo) or 1-3 (Axiom) six-pin connector and slide the female connector off bracket. Remove the Terminal Position Assurance (TPA) Lock from the connector. Locate the two blue wires in position 1 and 3 on the female connector. With appropriate tool (shown above), apply light pressure upward on the connector locking tab while gently pulling on the blue wire to release. Note :Never use force to remove a terminal from a connector. 5. Insert the two blues wires from the replacement Shift Lock Solenoid into the 1- 40 (Rodeo) or 1-3 (Axiom) female connector. It does not matter which blue wire is inserted into the 1 and 3 position. Gently tug the blue wires to make sure they are secure. NOTE :D iscard the extra 2-pin connector sub harness included with replacement Shift Lock Solenoid P/N 8-97181-068-2. 6. Reconnect the Shift Lock Solenoid 2-pin connector and reattach the two screws securing the Shift Lock Solenoid to the selector lever subassembly. 7. Reconnect the 1-40 (Rodeo) or 1-3 (Axiom) six-pin connector and slide the female connector onto the bracket. 8. Reinstall the Selector Lever Knob, Cover Assembly, Center, Front, and Rear Console Assemblies. Refer to the Selector Lever section in the Service Manual. 9. Check Shift Lock operation: a. With ignition key in “Lock” position, Selector lever should not move from “P” position. b. With ignition key in “ON” position and brake pedal depressed. Selector lever can be moved out of “P” position. c. Key can be removed only when turned to “LOCK” position and selector lever is in “P” position.

Related entry:

how to shift 2007 chevy impala without a key, 2002 mitsubishi eclipse testing shift solenoids, how to install transmission shift solenoid buick regal ls 2000, 2006 lucern shift lock release button, weare is the solinod pak on my2002mercury granmarquis, how to change a gear shif on a f 250 2001 aut, location a1 tshift selnoid 2002 trailblazer, access to shiofter column on f250 ford 2001 modle, infiniti i30 shift control solenoid, 2003 gmc yukon shift solenoid manuals,