kia carnival v6 firing order
You are searching repair manual in PDF format about kia carnival v6 firing order use another keyword for search another post or files
kia carnival v6 firing order Direct Download speed 5787 Kb/s
kia carnival v6 firing order Full Version speed 6767 Kb/s
Filed Under (Buick) by admin on 18-01-2011
Engine Electrical > Firing Orders Firing Orders To avoid confusion, always replace spark plugs and wires one at a time. Replacing spark plugs and wires one at a time will help prevent incorrect wire routing or cross-firing resulting from an incorrect firing order. If more than one wire is to be disconnected at a single time, be sure to tag all of the cables to assure proper installation. Also, be disconnecting the cables, compare the firing order and routing to these diagrams and note any differences for installation purposes. This will help assure the wires are properly installed.
Filed Under (Ford) by admin on 04-10-2010
Engine miss, spark knock, buck/jerk, surge and other driveability concerns may be caused by induction crossfire. This occurs because of improperly routed spark plug wires. ACTION: If spark plug replacement is performed, the correct firing order and spark plug wire routing is essential to prevent the possibility of induction crossfire between cylinders. Refer to the following procedures for inspection of the spark plug wire routing and firing order. Properly reroute the spark plug wires if required. FIRING ORDER ^ The firing order for 1987-1993 vehicles is 1-5-4-2-6-3-7-8. If # 7 and # 8, or # 2 and # 4 spark plug wires are routed next to each other at the separation bracket, an induction crossfire condition can occur. ^ The firing order for 1994 vehicles is 1-3-7-2-6-5-4-8. On these vehicles the # 1 and # 3, or # 5 and # 6 spark plug wires must be separated to eliminate the possibility of an induction crossfire. ^ To eliminate the possibility of the coil wire becoming disconnected, route the coil wire under the spark plug wires at the distributor cap. 1987-1993 VEHICLES
Filed Under (Ford) by admin on 23-04-2010
Torque Specs always torque bolts in three equal increments Lube or Sealer Torque to: Engine Oil 105 ft-lbs. Connecting Rod Bolts Engine Oil 45 ft-lbs. Engine oil 140 ft-lbs. (blind hole) (water jacket) Rocker Arms (non-adjustable) Engine Oil 20 ft-lbs. Engine Oil 25 ft-lbs. Engine Oil 15 ft-lbs. Cam Bolt (upper gear) Thread Locker 45 ft-lbs. Engine Oil 20 ft-lbs. Non- Hardening 30 ft-lbs. Sealer Engine Oil 10 ft-lbs. Flexplate (Automatic) Thread Locker 85 ft-lbs.
Filed Under (KIA) by admin on 04-06-2010
Description This bulletin provides information related to the Throttle Position Sensor (TPS) for Sorento & Sedona models. Some Sorento & Sedona vehicles may exhibit diagnostic trouble codes P0121 and/or P1121. This condition mainly occurs in high ambient or desert areas, and can be related to the occasional increase in contact resistance due to excessive wear of the inner elements of the TP sensor. This bulletin describes the proper service and adjustment procedure for replacing the TP Sensor. – Service Procedure Replacement Procedure: 1. Turn ignition OFF. Remove engine cover and disconnect electrical connector from TP Sensor. 2. Remove two (2) retaining screws from TP Sensor and remove from throttle body. 3. Install new TP Sensor to throttle body. Install retaining screws and hand tighten lightly. Adjustment will be required. Re-install electrical connector to TP Sensor.
Filed Under (KIA) by admin on 06-07-2010
Vehicle Level Powertrain Management Ignition System Ignition Coil Service and Repair Service and Repair REPLACEMENT IGNITION COIL 1. Remove the engine cover. 2. Disconnect the spark plug cables and the ignition coil connector. 3. Remove the ignition coil (A). 4. Installation is the reverse of removal. 2006 Kia Spectra L4-2.0L – Service and Repair