kia charcoal canister


You are searching repair manual in PDF format about kia charcoal canister use another keyword for search another post or files




2002 Hyundai Accent 1.6L, Vin C 2003 Hyundai Accent GS 1.5L Difficulty filling the gas tank The pump keeps clicking off

0

Filed Under (Hyundai) by admin on 25-04-2010

download
1. Disconnect the vapor line at the charcoal canister that comes from the liquid vapor separator and goes to the charcoal canister. See if the fuel tank can be easily filled then. 2. If the fuel tank can easily be filled with the vapor line removed from the charcoal canister, reconnect the vapor line and remove the other lines from the charcoal canister and see if the fuel tank can be easily filled. 3. If the fuel tank is once again difficult to fill, replace the charcoal canister. 4. If disconnecting the vapor line at the charcoal canister does NOT make the fuel tank easy to fill, then disconnect the vapor line from the liquid vapor separator at
the fuel tank in case the vapor line is plugged/restricted. Charcoal Canister Liquid Vapor Separator Vapor Line Fuel vapors are directed to the canister from the ORVR fill vent valve in the gas tank through the liquid vapor separator and to the canister. The metal tube that
loops up by the filler neck is part of the vapor line to the canister.

2007 Chevrolet Impala Evaporative Emission Canister Replacement Removal Procedure

0

Filed Under (Chevrolet) by admin on 22-10-2010

download
1. Remove the fuel tank. 2. Disconnect the evaporative emission (EVAP) line (3) from the canister.3. Reposition the EVAP canister hose clamp. 4. Remove the EVAP canister hose. 5. Disconnect the canister EVAP line from the fuel sender. 6. Squeeze the small retainer in front of the canister in order to disengage the canister. 7. Remove the EVAP canister. Installation Procedure Notice: Do not attempt to straighten kinked nylon pipes. Replace any kinked nylon pipes in order to prevent damage to the vehicle. Do not attempt to repair sections of nylon pipes. Replace damaged nylon pipes. Replace the vapor pipes with original equipment or parts that meet GM specifications. Replace the vapor hoses with original equipment or parts meeting GM specifications. Use only reinforced fuel-resistant hose identified with the word Fluoroelastomers or GM 6163M on the hose. 1. Install the EVAP canister. 2. Squeeze the small retainer in front of the canister in order to engage the canister. 3. Connect the canister EVAP line to the fuel sender. 4. Install the EVAP canister hose. 5. Position the EVAP canister hose clamp. 6. Connect the EVAP line (3) to the canister. 7. Install the fuel tank.

2004 Honda Accord EVAP Canister Vent Shut Valve Stuck Closed Malfunction

0

Filed Under (Honda) by admin on 05-11-2010

download
1. 2. 3. 4. Turn the ignition switch ON (II). Clear the DTC with the HDS. Remove the fuel fill cap for 5 seconds , then install it. Start the engine. Hold the engine speed at 3,000 rpm with no load (in Park or neutral) until the radiator fan comes on, then let it idle. Monitor the OBD STATUS for DTC P2422 in the DTCs MENU with the HDS. Does the screen indicate FAILED? YES – Go to step 6. NO – If the screen indicates PASSED, intermittent failure, system is OK at this time. Check for a poor connection or loose terminals at the EVAP canister vent shut valve and ECM/PCM. If the screen indicates NOT COMPLETED, go to step 2 and recheck. Clear the DTC with the HDS. Remove the EVAP canister vent shut valve from the EVAP canister. Connect the 2P connector to the EVAP canister vent shut valve. Turn the ignition switch ON (II). Do the EVAP CVS ON in the INSPECTION MENU with the HDS. 5. 6. 7. 8. 9. 10. 11. Check the EVAP canister vent shut valve (A) operation. Does the valve operate? YES – Check for a blockage in the EVAP canister, then install the EVAP canister vent shut valve, and go to step 14. NO – Go to step 12. 12. Turn the ignition switch OFF. 13. Replace the EVAP canister vent shut valve. 14. Turn the ignition switch ON (II). 15. Reset the ECM/PCM with the HDS. 16. Do the ECM/PCM idle learn procedure. 17. Turn the ignition switch OFF. 18. Remove the fuel fill cap for 5 seconds , then install it. 19. Start the engine. Hold the engine speed at 3,000 rpm with no load (in Park or neutral) until the radiator fan comes on, then let it idle. 20. Check for Temporary DTCs or DTCs with the HDS. Are any Temporary DTCs or DTCs indicated? YES – If DTC P2422 is indicated, check for poor connections or loose terminals at the FTP sensor or the EVAP canister vent shut valve and the ECM/PCM, then go to step 1. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTC’s troubleshooting. NO – Go to step 21. 21. Monitor the OBD STATUS for DTC P2422 in the DTCs MENU with the HDS. Does the screen indicate PASSED? YES – Troubleshooting is complete. NO – If the screen indicates FAILED, check for poor connections or loose terminals at the FTP sensor or the EVAP canister vent shut valve and the ECM/PCM, then go to step 1. If the screen indicates NOT COMPLETED, go to step 16 and recheck.

2000 Buick LeSabre Canister REMOVAL PROCEDURE

0

Filed Under (Buick) by admin on 25-07-2010

download
REMOVAL PROCEDURE CAUTION: Refer to Hoist Caution in Service Precautions. 1. Raise the vehicle. Refer to Vehicle Lifting. 2. Mark the hoses for installation on the EVAP canister. 3. Remove the EVAP vent hose (1). 4. Remove the fuel tank vapor hose (2). 5. Remove the purge hose (3). 6. Remove the nuts (2) from the EVAP canister. 7. Remove the EVAP canister (1) from the bracket by releasing the tabs. INSTALLATION PROCEDURE 1. Install the EVAP canister on the bracket. 2. Install the EVAP canister assembly into the vehicle. NOTE: Refer to Fastener Notice in Service Precautions. 3. Assemble the EVAP canister to the underbody with the 3 nuts. Tighten Tighten the nuts to 9 Nm (80 lb in) . 4. Install the purge hose (3) to the EVAP canister. 5. Install the fuel tank vapor hose (2) to the EVAP canister. 6. Install the vent hose (1) to the EVAP canister 7. Lower the vehicle.

2005-2008 FORD F-250, F-350 SLOW FUEL FILL MIL ON WITH DTC P0191

0

Filed Under (Ford) by admin on 06-01-2011

download
ISSUE Some 2005-2008 F-Super Duty 250/350 vehicles equipped with a 5.4L 3V or 6.8L 3V engine may experience premature automatic shut off of the fuel fill nozzle, or repeated fuel shut off at the fuel station delivery nozzle with malfunction indicator lamp (MIL) on with diagnostic trouble code (DTC) P0191. Vehicles operated in muddy or dusty environments can encounter a dirt clogged carbon canister system. More specifically, the carbon canister’s vent, fresh air box, and filters become clogged with dirt from operating in such environments. SERVICE PROCEDURE Inspect the vehicle canister system and if it found to be dirt clogged then continue with this TSB. NOTE IF THE VEHICLE’S CANISTER SYSTEM IS NOT DIRT CLOGGED, THEN PROCEED WITH NORMAL DIAGNOSTICS AND DO NOT CONTINUE WITH THIS TSB. Vehicles with Pickup Boxes: 1. Replace the carbon canister assembly with a canister built after 10/1/2006. This canister has a revised internal filter media, and went into production on 10/1/2006. The date code is on a black sticker located on the carbon canister assembly. 2. Relocate the fresh-air intake port to a more protected location using the fresh air hose kit, for pickup applications only. 3. Replace fuel cap assembly if the vehicle was built before 5/16/2007. Vehicles with Pickup Box Removed or Chassis Cab: 1. Replace the carbon canister assembly with a canister built after 10/1/2006. This canister has a revised internal filter media, and went into production on 10/1/2006. The date code is on a black sticker located on the carbon canister assembly. 2. Relocate the fresh-air intake port to a more protected location using QVM bulletin Q-132 at the body builder’s website – https://www.fleet.ford.com/truckbbas/index.htm for fresh air intake routing recommendations. 3. Replace fuel cap assembly if the vehicle was built before 5/16/2007.