kia sedona diagram


You are searching repair manual in PDF format about kia sedona diagram use another keyword for search another post or files



  kia sedona diagram Direct Download speed 5787 Kb/s

  kia sedona diagram Full Version speed 6767 Kb/s




Kia Sorento/ Kia Sedona Throttle Position Sensor W/3.5L Engine

0

Filed Under (KIA) by admin on 04-06-2010

download
Description This bulletin provides information related to the Throttle Position Sensor (TPS) for Sorento & Sedona models. Some Sorento & Sedona vehicles may exhibit diagnostic trouble codes P0121 and/or P1121. This condition mainly occurs in high ambient or desert areas, and can be related to the occasional increase in contact resistance due to excessive wear of the inner elements of the TP sensor. This bulletin describes the proper service and adjustment procedure for replacing the TP Sensor. – Service Procedure Replacement Procedure: 1. Turn ignition OFF. Remove engine cover and disconnect electrical connector from TP Sensor. 2. Remove two (2) retaining screws from TP Sensor and remove from throttle body. 3. Install new TP Sensor to throttle body. Install retaining screws and hand tighten lightly. Adjustment will be required. Re-install electrical connector to TP Sensor.

Related entry:

2005 kia sorento error code p0350, diagram 2005 kia sorento ac compressor bracket, 2004 kia sorento 3 5 firing order, KIA SEDONA AC COMPRESSOR REMOVAL, wire diagram for 2005 kia sedona refrigerationsystem, 2005 Kia Sorento AC Diagram, kia sorento 2 5engine handbook, cooling lines on a 2003 kia sedona, coolant temp sending unit on kia sedona 04, 2006 kia sorento ex fuse panel,

2002 Kia Sedona No start condition with trouble code P0335 present

0

Filed Under (KIA) by admin on 22-05-2010

download
Customer Concern: No start condition with trouble code P0335 present. Customer said it started to sputter and then would not start after they shut it off. Tests/Procedures: 1. Check the hall effect sensor while cranking on the Yellow/Green wire. A 5 volt square wave is normal. This signal should be consistent and clean. Also verify the Black wire has a good ground and the Brown wire has battery voltage at the crankshaft position sensor. 2. There is a plate in the front of the engine that triggers the crankshaft sensor, verify the timing belt or some debris has not bent or damaged the sensor plate. Potential Causes: Crankshaft Position (CKP) Sensor Wiring

TOYOTA RAV4 ELECTRICAL WIRING DIAGRAM

0

Filed Under (Toyota) by admin on 28-09-2009

ELECTRICAL WIRING DIAGRAM
This Service Bulletin is to inform you of the Electrical Wiring Diagram for RAV4 equipped with 1CD-
FTV engine.RELAY LOCATIONS ELECTRICAL WIRING ROUTING OVERALL ELECTRICAL WIRING DIAGRAM CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS

download

Related entry:

liteace instrument panel diagram, NISSAN 1400 WIRING DIAGRAM, 69 buick riviera complete wire diagram, wiring diagram for power windows in a 1999 jeep grand Cherokee, international prostar ac system wiring, wiring diagram windows 98 chevy silverado, ABS Harness Impala diagram, diagram for 02 trailblazer 5v circuit, 2005 impala wiring diagram, 98 chevy silverado,

2004 Kia Sorento EX TIMING BELT REMOVAL & INSTALLATION

0

Filed Under (KIA) by admin on 25-04-2010

download
Disconnect negative battery cable. Remove engine cover. Using 16-mm spanner wrench, rotate serpentine belt tension arm clockwise about 14 degrees to relieve belt tension. Remove serpentine drive belt. Remove power steering pump pulley, idler pulley, tensioner pulley and crankshaft pulley. Remove upper and lower timing belt covers. See Fig. 1 or Fig. 2 .
NOTE: Rotate crankshaft clockwise and align timing mark to set No. 1 cylinder to TDC on compression stroke. 2. Ensure timing marks of camshaft sprocket and cylinder head cover are matching. See Fig. 5 . On Sedona, support engine with jack and remove engine mounting insulator. On all models, remove auto tensioner. See Fig. 3 . NOTE: If timing belt is to be reused, mark rotational directionon belt for reinstallation reference. CAUTION: If either camshaft is set at TDC for cylinder No. 1 at the compression
stroke and the corresponding camshaft on the same cylinder head is rotated 180 degrees while the timing belt is removed, intake and
exhaust valves may contact each other. 3. Unbolt timing belt tensioner pulley, and remove timing belt.

Related entry:

diagram of a 2007 kia sorento engine with pulleys, 2004 sorento timing marks, diagram of belt and pulleys 2007 kia sorento, diagram of pulleys in kia sorento, kia sorento timing belt marks,

2006 Kia Spectra REPLACEMENT IGNITION COIL

0

Filed Under (KIA) by admin on 06-07-2010

download
Vehicle Level Powertrain Management Ignition System Ignition Coil Service and Repair Service and Repair REPLACEMENT IGNITION COIL 1. Remove the engine cover. 2. Disconnect the spark plug cables and the ignition coil connector. 3. Remove the ignition coil (A). 4. Installation is the reverse of removal. 2006 Kia Spectra L4-2.0L – Service and Repair

Related entry:

where is the thermostat on the Kia engine DOHC16v, where is the evaporater located on a kia spectra, the conector to read the code on a kia 95, oriface tube location on 2006 kia spectra ex, knock sensor location 2005 kia 1 9 dohc, kia spectra pyrotechnic seatbelt pretensioner, how to replace antenna kia spectra, how to install a 2005 kia spectra engine computer 2 liter, 2007 kia spectra seatbelt pretensioner parts, 2007 kia spectra pretensioner pyro,