kia spectra sensor diagram


You are searching repair manual in PDF format about kia spectra sensor diagram use another keyword for search another post or files



  kia spectra sensor diagram Direct Download speed 5787 Kb/s

  kia spectra sensor diagram Full Version speed 6767 Kb/s




2002 Kia Spectra SENDING UNITS & SENSORS LOCATION

0

Filed Under (KIA) by admin on 13-06-2010

download
Air Quality Sensor At center front of engine compartment. Camshaft Position Sensor On rear of cylinder head. See Fig. 1 . Chassis Acceleration Sensor At right rear side of engine compartment. Crankshaft Position Sensor On left front side of transaxle. See Fig. 1 . Engine Coolant Temperature On top rear of engine, near thermostat. See Fig. 1 . Sensor Fuel Tank Unit On top of fuel tank, below rear seat cushion. Hot Film Airflow Sensor On end of air intake hose, at air cleaner housing. See Fig. 1 . Knock Sensor Near center rear of engine compartment, on intake manifold support bracket. O2 Sensor (Down) On front exhaust pipe, downstream of warm-up TWC converter. O2 Sensor (Up) On exhaust manifold, upstream of warm-up TWC converter. Speed Sensor On top of transaxle. Thermocon Behind glove box, on HVAC assembly. See Fig. 2 . Throttle Position Sensor On throttle body. See Fig. 1 . Turbine Sensor (A/T) On top rear of transaxle. Wheel Speed Sensor (Left Front) Attached to left front hub spindle. Wheel Speed Sensor (Left Rear) Attached to left rear hub spindle. Wheel Speed Sensor (Right Attached to right front hub spindle. Front) Wheel Speed Sensor (Right Rear) Attached to right rear hub spindle.

Related entry:

heater sensor for chevy thahoe 96, location of crankshaft sensor on 2000 mercury villager, 1999 sunfire sensor bank2, where is the oxygen sensor downstream on a 2004 ford escape, where is the downstream oxygen sensor located 2004 ford escape, where is cam sensor located isuzu axium, where are the speedometer sensors on an 06 kia spectra, What does the mapping sensor do on a 1999 Pontiac Grand Am do, vss on malibu 2005 diagram, replace backup sensors on 2005 lincoln town car,

1995 Ford Mustang Camshaft Position (CMP) Sensor Removal Installation

0

Filed Under (Ford) by admin on 08-02-2011

download
1. Disconnect battery ground cable (14301) . 2. Disconnect fuel charging wiring (9D930) from distributor stator (12A112) (camshaft position sensor). 3. Remove stator camshaft position sensor retaining screws and distributor stator (camshaft position sensor) from camshaft position sensor housing. 4. If removing camshaft position sensor housing from the engine front cover (6019) , proceed with Removal Step 5. If camshaft position sensor housing is not being removed, proceed to Installation Step 6. 5. CAUTION: Before proceeding with this procedure, set cylinder No. 1 to 26 degrees After Top Dead Center (ATDC) of the compression stroke. Then note the position of the stator (camshaft position sensor) electrical connector. The installation procedure requires that the connector be located in the same position. Remove retaining bolt and hold-down clamp (12270) . 6. NOTE: The oil pump intermediate shaft (6A618) should be removed with the camshaft position sensor housing. Remove camshaft position sensor housing from engine front cover . Installation 1. CAUTION: If the replacement distributor stator (camshaft position sensor) does not contain a plastic locator cover tool, a special service tool such as Syncro Positioning Tool T89P-12200-A must be obtained prior to installation of the replacement distributor stator (camshaft position sensor). Failure to follow this procedure will result in improper stator (camshaft position sensor) alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage. If the plastic locator cover tool is not attached to the replacement distributor stator (camshaft position sensor), attach Syncro Positioning Tool T89P-12200-A as follows: a. Engage camshaft position sensor housing vane into the radial slot of the tool. b. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing. The cover tool should be square and in contact with entire top surface of camshaft position sensor housing. 2. Transfer oil pump intermediate shaft from old camshaft position sensor housing to replacement camshaft position sensor housing. 3. CAUTION: If stator (camshaft position sensor) electrical connector is not positioned properly (for example, contacting the A/C compressor bracket), DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1. Install camshaft position sensor housing so that drive gear engagement occurs when arrow on locator tool is pointed approximately 30 degrees counterclockwise from the front face of the cylinder block (6010) . This step will locate stator (camshaft position sensor) electrical connector in the pre-removal position. 4. Install hold-down clamp and retaining bolt and tighten bolt to 20-30 Nm (15-22 lb-ft). 5. Remove Syncro Positioning Tool T89P-12200-A. 6. CAUTION: If stator (camshaft position sensor) electrical connector is not positioned properly (for example, contacting the A/C compressor bracket), DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1. Install distributor stator (camshaft position sensor) and retaining screws. Tighten screws to 2.5-3.5 Nm (22-31 lb-in). 7. Connect fuel charging wiring connector to distributor stator (camshaft position sensor). 8. Connect battery ground cable .

Related entry:

cam positioning tool for 2002 landrover freelander 2 5 liter, 2003 caddilac seville yaw rate sensor, lincoln aviator v-8 4 6 litre engine oxygen sensor locations, 95 cadillac conccourse cam sensor issue, dpfe 01 307, lhow diagram of ckp 0ninfiniti j 30, throttle position sensor 91 riviera, map/sensor/subaru forestor/2001, location if map sensor on 2004 sebring 2 7, 2009 ford focus throttle position sensor,

1998 Ford Windstar Camshaft Position (CMP) Sensor REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 17-02-2011

download
CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126) , set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Then note the position of the camshaft position sensor electrical connector. The installation procedure requires the connector be located in the same position. Removal 1. Disconnect battery ground cable (14301). Refer to Section 14-01. 2. Disconnect fuel charging wiring connector from camshaft position sensor. 3. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing. 4. If removing camshaft position sensor housing from the cylinder block (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to Step 6 of the installation procedures. 5. Remove hold-down clamp (12270) (bolt and washer assembly). 6. NOTE: Remove the oil pump intermediate shaft (6A618) with the camshaft position sensor housing. Remove camshaft position sensor housing from cylinder block. Installation 1. CAUTION: If the replacement camshaft position sensor housing does not contain a plastic locator cover tool, a special service tool must be obtained prior to installation of the replacement camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the ignition fuel system being out of time with the engine, possibly causing engine damage. NOTE: For 3.0L engines, use Syncro Positioning Tool 303-589. For 3.8L engines, use Syncro Positioning Tool 303-562 (T96T-12200-A). If the plastic locator cover tool is not attached to the replacement camshaft position sensor housing, attach syncro positioning tool as follows: a. Engage camshaft position sensor housing vane into the radial slot of the tool. b. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing. 2. Transfer oil pump intermediate shaft from old camshaft position sensor housing to replacement camshaft position sensor housing. 3. Install camshaft position sensor housing so drive gear engagement occurs when arrow on syncro positioning tool is pointed approximately as shown in the illustrations. This step will locate camshaft position sensor electrical connector in the pre-removal position. 4. Install hold-down clamp (washer and bolt assembly) and tighten bolt to 20-30 Nm (15-22 lb-ft). 5. Remove syncro positioning tool. 6. CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1. Install camshaft position sensor and retaining screws. On 3.0L engine, tighten screws to 2.5-3.5 Nm (23-30 lb-in). On 3.8L engine, tighten screws to 4.5-7 Nm (40-61 lb-in). 7. Connect fuel charging wiring connector to camshaft position sensor. 8. Connect battery ground cable. Refer to Section 14-01. Camshaft Position Sensor—3.0L Engine

Related entry:

installing tps sensor on a ford escort, diagram camshaft position sensors for 2002 santa fe, what sensors on back of block 5 3, 2007 sonata throttle position sensor for sale, were is the over drive range sensor located at on a 2002 windstar, tcc on astor van, replacing tps in 1999 ford escort, 06 kia sorento camshaft positioning sensor, any reviews of ktc tools, adjusting range sensor 1998 saturn sl,

2003-2006 Chevrolet Express Antilock Brake (ABS) Activation At Low Speeds (Clean Wheel Speed Sensor Mounting Surface)

0

Filed Under (Chevrolet) by admin on 25-01-2011

download
Condition Some customers may comment on ABS activation at low speeds, usually below 8 km/h (5 mph). Upon investigation, the technician will find no DTCs set. Cause The cause of this condition may be an increased air gap between the wheel speed sensor and the hub reluctor ring due to rust and debris built up on the sensor mounting surface. Correction Measure AC voltage and clean the wheel speed sensor mounting surfaces. 1. 2. 3. 4. Raise and support the vehicle. Disconnect both the front wheel speed sensor connectors at the frame and harness. Place a Digital Volt Meter (DVM) across the terminals of each wheel speed sensor connector. Rotate the wheel clockwise approximately one revolution per second. The minimum reading should be at least 350 ACmV’s. If the reading is less than 350 ACmV’s, remove the wheel speed sensor. 5. Plug the wheel speed sensor bore in order to prevent debris from falling into the hub during service. 6. Clean the wheel speed sensor mounting surface using a wire brush, sand paper, emery cloth, scotch brite, or other suitable material. Be sure to thoroughly clean the wheel speed sensor surface. There should be no rust or corrosion. 7. Check the sensor head to determine if it has been warped/distorted due to the corrosion build up or other causes. Check the mounting surface on the sensor head for flatness by placing it on the edge of a metal machinists scale or other suitable straight edge to measure the flatness. Check the sensor for flatness in multiple (minimum 3) positions/directions. If the sensor head is distorted, replace the sensor. 8. Apply (spray) two thin coats of the specified rust penetrating lubricant (corrosion inhibitor) to the complete sensor mounting surface on the bearing hub. Allow to dry for 3-5 minutes between coats. Use ONLY Rust Penetrating Lubricant, P/N 89022217 (in Canada, P/N 89022218). 9. When the corrosion inhibitor is dry to the touch (about 10 minutes), apply a thin layer of bearing grease to the hub surface and sensor O-ring prior to sensor installation. Use ONLY Wheel Bearing Lubricant, P/N 01051344 (in Canada, P/N 993037). 10.Install either the original sensor or a new one in the hub. Ensure that the sensor is seated flush against the hub. Refer to the applicable Wheel Speed Sensor Replacement procedure in the ABS sub-section of the Service Manual. 11.Place the DVM across the sensor terminals and recheck the voltage while rotating the wheel. The voltage should now read at least 350 ACmV’s.

Related entry:

2005 highlander rear wheel bearing and speed sensor harness, mitsubishi lancer speed sensor removal, 1998 dodge caravan 3 8L speed sensor location diagrahm, 2004 toyota tundra abs activates at low speed, mondeo mk3 snaped wheel speed sensor off in hub, 2006 uplander disconnect sir system, Toyota Hilux Speed Sensor Ln106 Hilux Wiring Diagram, PO793, 2002 chevy cavalier 2 2 engine speed sensors, 99 b3000 speed sensor location,

Kia Sorento/ Kia Sedona Throttle Position Sensor W/3.5L Engine

0

Filed Under (KIA) by admin on 04-06-2010

download
Description This bulletin provides information related to the Throttle Position Sensor (TPS) for Sorento & Sedona models. Some Sorento & Sedona vehicles may exhibit diagnostic trouble codes P0121 and/or P1121. This condition mainly occurs in high ambient or desert areas, and can be related to the occasional increase in contact resistance due to excessive wear of the inner elements of the TP sensor. This bulletin describes the proper service and adjustment procedure for replacing the TP Sensor. – Service Procedure Replacement Procedure: 1. Turn ignition OFF. Remove engine cover and disconnect electrical connector from TP Sensor. 2. Remove two (2) retaining screws from TP Sensor and remove from throttle body. 3. Install new TP Sensor to throttle body. Install retaining screws and hand tighten lightly. Adjustment will be required. Re-install electrical connector to TP Sensor.

Related entry:

comocanviar un conpresor de kia sedona 2002, 2005 kia sorento error code p0350, 2007 kia sedona fuse diagram, 2003 kia sorento carcoal canister, B1346 Kia, diagram of drain for a sunroof drain for a 2006 kia sorento, 2003 kia sorento cooling diagram, 2006 kia serento cooling system diagram, 2005 kia sedona a/c diagram, kia sorento sunroof drain tubes,