kia vent valve


You are searching repair manual in PDF format about kia vent valve use another keyword for search another post or files



  kia vent valve Direct Download speed 5787 Kb/s

  kia vent valve Full Version speed 6767 Kb/s




2000 Buick LeSabre Canister Vent Valve Service and Repair REMOVAL INSTALLATION PROCEDURE

0

Filed Under (Buick) by admin on 08-07-2010

download
REMOVAL PROCEDURE 1. Turn OFF the ignition. CAUTION: Refer to Hoist Caution in Service Precautions . 2. Raise the vehicle. Refer to Vehicle Lifting. 3. Bend the retaining tab for the EVAP canister vent valve. 4. Remove the valve from the bracket. 5. Disconnect the electrical connector from the EVAP canister vent valve. 6. Loosen the vent hose clamp and remove the vent hose from the EVAP vent valve. 7. Remove the EVAP canister vent valve from the vehicle. INSTALLATION PROCEDURE 1. Connect the vent hose to the EVAP canister vent valve and tighten the hose clamp. 2. Connect the electrical connector to the EVAP canister vent valve. 3. Install the EVAP canister vent valve to the bracket. 4. Bend the retaining tab for the EVAP canister vent valve. 5. Lower the vehicle

Related entry:

449 code 08 impala, 1999 buick lesabre mid vent actuator, 05 ford f250 canister vent soleniod location, how much is a evaporative vent valve for a 2007 Rendevouz, how to remove air vents on dash of 2005 jaguar xj8, how to remove side air vents from 2005 jaguar xj8, ldp vent valve 2003 town&country location, saturn vent solenoid removal, vent valve on a 98 nissan sentra gxe, vent valve solenoid 2010 chevy hhr,

2004 Honda Accord EVAP Canister Vent Shut Valve Stuck Closed Malfunction

0

Filed Under (Honda) by admin on 05-11-2010

download
1. 2. 3. 4. Turn the ignition switch ON (II). Clear the DTC with the HDS. Remove the fuel fill cap for 5 seconds , then install it. Start the engine. Hold the engine speed at 3,000 rpm with no load (in Park or neutral) until the radiator fan comes on, then let it idle. Monitor the OBD STATUS for DTC P2422 in the DTCs MENU with the HDS. Does the screen indicate FAILED? YES – Go to step 6. NO – If the screen indicates PASSED, intermittent failure, system is OK at this time. Check for a poor connection or loose terminals at the EVAP canister vent shut valve and ECM/PCM. If the screen indicates NOT COMPLETED, go to step 2 and recheck. Clear the DTC with the HDS. Remove the EVAP canister vent shut valve from the EVAP canister. Connect the 2P connector to the EVAP canister vent shut valve. Turn the ignition switch ON (II). Do the EVAP CVS ON in the INSPECTION MENU with the HDS. 5. 6. 7. 8. 9. 10. 11. Check the EVAP canister vent shut valve (A) operation. Does the valve operate? YES – Check for a blockage in the EVAP canister, then install the EVAP canister vent shut valve, and go to step 14. NO – Go to step 12. 12. Turn the ignition switch OFF. 13. Replace the EVAP canister vent shut valve. 14. Turn the ignition switch ON (II). 15. Reset the ECM/PCM with the HDS. 16. Do the ECM/PCM idle learn procedure. 17. Turn the ignition switch OFF. 18. Remove the fuel fill cap for 5 seconds , then install it. 19. Start the engine. Hold the engine speed at 3,000 rpm with no load (in Park or neutral) until the radiator fan comes on, then let it idle. 20. Check for Temporary DTCs or DTCs with the HDS. Are any Temporary DTCs or DTCs indicated? YES – If DTC P2422 is indicated, check for poor connections or loose terminals at the FTP sensor or the EVAP canister vent shut valve and the ECM/PCM, then go to step 1. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTC’s troubleshooting. NO – Go to step 21. 21. Monitor the OBD STATUS for DTC P2422 in the DTCs MENU with the HDS. Does the screen indicate PASSED? YES – Troubleshooting is complete. NO – If the screen indicates FAILED, check for poor connections or loose terminals at the FTP sensor or the EVAP canister vent shut valve and the ECM/PCM, then go to step 1. If the screen indicates NOT COMPLETED, go to step 16 and recheck.

Related entry:

location of cansiter evap on 2004 honda pilot, 2004 suzuki verona evap vent valve, 2012 mazda 5 evap system schematic, saturn vue 2007 evap selenoid P0445, 2002 vw cabrio evap sysrem, how remove the evap canister from a 97 lumina, 2006 gs300 evap drain, 2004 jeep liberty ac not working good vaccum cannister, How to install purge evaporator lines on 93 Jeep Wrangler, how to remove a vent valve in a 2004 suzuki verona,

1995 Ford Windstar VALVE CLEARANCE ADJUSTMENT

0

Filed Under (Ford) by admin on 17-03-2011

download
NOTE: Hydraulic valve lifters are used; no valve adjustment is required. When valve and/or valve seat is machined, valve clearance is reduced and may cause improper valve operation. Different length push rods are available for correcting clearance. Valve lifter must be collapsed to check valve clearance. 1. With valve cover removed, position piston No. 1 at TDC of compression stroke. Completely collapse cylinder No. 1 intake valve lifter and hold valve lifter collapsed. Using feeler gauge, measure clearance between rocker arm and valve stem. 2. Clearance should be within specification. Refer to COLLAPSED VALVE LIFTER CLEARANCE table. Replace push rod, if necessary, to obtain correct clearance. 3. Position crankshaft as specified. See, in this article, VALVE CLEARANCE CHECKING SEQUENCE table, and check appropriate valves. Replace push rods if clearance is not within specification. 4. If push rod(s) is replaced, ensure corresponding cylinder piston is below TDC. It will be necessary to loosen or remove rocker arm to replace push rod. CAUTION: DO NOT operate or crank engine after installing push rod until valve lifter has leaked down to normal operating position. COLLAPSED VALVE LIFTER CLEARANCE

Related entry:

remove rear expansion valve on 2008 yokon, 02 camry how to replace expansion valve, changing valve lifters from 2000 toyota corolla le, where is the expansion valve in suburban 1500, 2007 ford 500 refrigeant control valve located, 2002 chevy malibu expansion balve replacement, dodge durango 2002 slt ac expansion valve location, location of expansion valve in 2003 cadillac cts, vaper valve 2006 cts cadlac, 2005 toyota sienna ac expansion valve replacement,

1992 Suzuki Swift VALVE CLEARANCE ADJUSTMENT

0

Filed Under (Suzuki) by admin on 26-05-2011

download
NOTE: Samurai & Sidekick 1) Remove rocker cover. Rotate crankshaft until zero degree (TDC) timing mark of timing belt cover is in line with timing mark on crankshaft pulley. 2) Cylinder No. 1 should be at TDC on compression stroke. Remove distributor cap, and ensure rotor is pointed upward at distributor hold-down bolt and to No. 1 terminal of distributor cap. If not as described, rotate crankshaft 360 degrees. 3) Measure valve clearance between adjustment screw and valve stem using thickness gauge. Check intake valve clearance of cylinders No. 1 and 2 and exhaust valve clearance of cylinders No. 1 and 3. 4) Turn crankshaft one complete revolution (360 degrees). Check intake valve clearance of cylinders No. 3 and 4 and exhaust valve clearance of cylinders No. 2 and 4. Ensure clearance is within specification. See VALVE CLEARANCE SPECIFICATIONS table. 5) If clearance adjustment is necessary, loosen lock nut and turn adjusting screw. After adjusting clearance, tighten adjusting Swift DOHC uses hydraulic lifters. Adjustment is not required. screw lock nut to 11-14 ft. lbs. (15-19 N.m) on Samurai or 90-108 INCH lbs. (10-13 N.m) on Sidekick. On all models, recheck clearance. VALVE CLEARANCE SPECIFICATIONS TABLE ¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡ Application SOHC Engines Samurai, Sidekick 8-Valve TBI & Swift (1) Engine Cold Exhaust ……………………. .006-.008 (.15-.20) Intake …………………….. .005-.007 (.13-.17) Engine Hot Exhaust ……………………. .010-.012 (.25-.30) Intake …………………….. .009-.011 (.23-.27) Sidekick 16-Valve PFI Engine Cold Exhaust & Intake ………….. .0031-.0047 (.08-.12) Engine Hot Exhaust & Intake ………….. .0047-.0063 (.12-.16) DOHC Engine Swift (1) …………………………………. (2) (1) – Swift is available with 1.3L DOHC and SOHC engines. (2) – Hydraulic valve lash adjusters are used. Adjustment is not required. ¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡ Swift SOHC 1) Remove rocker cover. Remove right side inner fender apron extension to enable timing marks to be seen. Align crankshaft pulley timing mark with TDC mark on timing belt cover. 2) Remove distributor cap. Ensure rotor is pointing upward toward distributor hold-down bolt and to No. 1 terminal of distributor cap. If not as described, rotate crankshaft 360 degrees. 3) Measure valve clearance between adjustment screw and valve stem using thickness gauge. Check intake valve clearance of cylinders No. 1 and 2 and exhaust valve clearance of cylinders No. 1 and 3. Turn crankshaft one complete revolution (360 degrees). Check intake valve clearance of cylinders No. 3 and 4 and exhaust valve clearance of cylinders No. 2 and 4. 4) Ensure clearance is within specification. See VALVE CLEARANCE SPECIFICATIONS table. If clearance adjustment is necessary, loosen lock nut and turn adjusting screw. Hold adjusting screw while tightening lock nut to 11-14 ft. lbs. (15-19 N.m). Recheck clearance. In. (mm)

Related entry:

sequent of tighining valve cover gasket nuts of 2000 bmw z3, 2001 chevy malibu valve adjustment 6 cylander, 2003 miata vvt 10 degrees out, valve adjustment 1992 toyota corolla, valve adjustment 01 forester, toyota 3zze enggine timing marks, buy purge control selenoid for 2008 suzuki xl7, purge sensor location 2008 suzuki xl7, 96 3 8l valve cover removal, 96 ford ranger 3 0 valve adjustment,

1996 Ford Taurus valve body Removal and Installation

0

Filed Under (Ford) by admin on 16-10-2010

download
REMOVAL NOTE: The oil pump and valve body are removed as an assembly. 1. Disconnect battery ground cable, then remove battery, battery tray, and remote air cleaner. 2. Position supply hoses, vacuum hoses, and wiring away from pump and valve body cover. 3. Remove shift lever. 4. On models equipped with Anti-lock Brake System (ABS) , remove splash shield cover, then disconnect brake reservoir hose and cap to prevent contamination. 5. On all models, remove EGR bracket attaching bolts, then install lifting eye. 6. Remove throttle body bracket attaching bolt, install lifting eye, then using suitable equipment support engine. 7. Remove lefthand transaxle mount. 8. Remove transaxle side pan upper attaching bolts. 9. Raise and support vehicle. 10. Remove lefthand front wheel and tire assembly. 11. Remove inner fender cover and position aside, then disconnect ride height sensor. 12. Remove rear transaxle mount attaching bolt. 13. Loosen but do not remove two lefthand subframe attaching bolts. 14. Remove two engine support mount attaching bolts. 15. Remove four lefthand engine support attaching bolts, then remove the engine support. 16. Position suitable drain pan, then remove remaining transaxle side pan attaching bolts and remove pan. 17. Using suitable screwdriver, place manual shift shaft in Park position. 18. Disconnect upper bulkhead electrical connector wiring retainer clip from valve body. 19. Disconnect electrical connectors. Oil Pump And Valve Body Bolt Removal 20. Remove valve body attaching bolts, then disengage linkage and remove valve body. NOTE: Do not remove oil pump cover attaching bolts. INSTALLATION 1. Install new pump and valve body to chain cover gasket. 2. Slide pump and valve body onto pump shaft. 3. Rotate pump and valve body assembly toward dash panel, then engage manual valve link with manual valve. 4. Slightly rotate pump and valve body assembly to engage oil pump shaft splines with oil pump rotor splines. Valve body should slide flush with chain cover. A suitable 7/8 inch deep well socket on crankshaft pulley may be required for complete engagement. 5. On models less anti-skid, if engagement is not as indicated in step 4, proceed as follows: a. Remove manual valve from valve body. b. Rotate assembly to allow full engagement, up to 360° . c. After full engagement, return assembly to installed position, then install manual valve.

Related entry:

4l60e valve body bolt location, 722 3 transmission USED valve BODY, ford 6r60 valve body check ball, 6r60 upper valve body check ball installation, 2006 nissan xterra transmission valve body, 09g body valve torque spec, 6R60 valve body removal, 2006 4300 body controller, valve body torque specs lincoln ls, 4hp22 transmission valve body diagram,