location of idle air control valve on 2001 rav4
You are searching repair manual in PDF format about location of idle air control valve on 2001 rav4 use another keyword for search another post or files
location of idle air control valve on 2001 rav4 Direct Download speed 5787 Kb/s
location of idle air control valve on 2001 rav4 Full Version speed 6767 Kb/s
Filed Under (Oldsmobile) by admin on 10-04-2011
Refer to Engine Controls Schematics MAF, Secondary Air Injection Pump Bypass Solenoid, IAC and Secondary AIR Pump . Circuit Description The AIR pump is used on this vehicle to lower tail pipe emissions on start-up. The powertrain control module (PCM) grounds the AIR pump relay control circuit, which energizes the AIR pump. The PCM also grounds the AIR solenoid valve control circuit, which energizes the AIR solenoid valve. The AIR solenoid valve opens allowing manifold vacuum to open the AIR control valves. The PCM enables both control circuits when AIR system operation is desired. When the AIR system is active, the AIR pump forces fresh air into the exhaust stream in order to accelerate catalyst operation. The AIR control valves replace the conventional check valves. When the AIR system is inactive, the AIR control valves prevent air flow in either direction. DTC P0412 applies to the AIR solenoid control circuit. DTC P0418 applies to the AIR pump relay control circuit. DTC P0410 sets if an air flow problem is detected. The PCM will run two tests using the heated oxygen sensor (HO2S) voltage to diagnose the AIR system. Both tests have two parts. The passive test is performed during regular AIR pump operation. The passive test consists of the following: Passive Test Part 1 When the AIR system is enabled, the PCM monitors the HO2S voltage. If the HO2S voltage goes below a threshold, the PCM interprets this as an indication that the AIR system is operational. Passive Test Part 2 When the AIR system is disabled, the PCM monitors the HO2S voltage. The HO2S voltage should increase above a threshold and switch normally. If both of these tests indicate a pass, no further action is taken. If one of the above tests failed or is inconclusive, the diagnostic will proceed to test two. The active test is performed specifically for diagnostic purposes. Test two consists of the following: Active Test Part 1 During this test the PCM turns the AIR system on during closed loop operation. When the AIR system is activated, the PCM monitors the HO2S voltage. If the AIR system is operating properly, the HO2S voltage should go below a predetermined threshold. Active Test Part 2 The PCM turns the AIR system off. The HO2S voltage should return to above a rich threshold.
Related entry: ford 500 air conditioner problems
, idle air control valve symptoms 5 4 triton
, idle control module audi a6
, can a air suspension be repair on a 2000 lincoln continental?
, replace intake air control valve 2002 sienna
, schematics for heating 1999 silverado
, 2003 ford escape how to adjust idle rpm
, idle adjustment 2001 pathfinder 3 5
, 2001 chevy venture secondary air injection module
, Airbag solenoid valve for a 2001 Lincoln Continental
Filed Under (Honda) by admin on 21-12-2010
NOTE: If DTC P1519 is stored at same time as DTC P0505, troubleshoot DTC P1519 first, then recheck for DTC P0505. 1. Start the engine. Hold the engine at 3,000 rpm with no load (in Park or neutral) until the radiator fan comes on. 2. Check the engine speed at idle with no-load conditions: headlights, blower fan, rear window defogger, radiator fan, and air conditioner off. Is the engine running at 730+/-50 rpm? YES – Intermittent failure, system is OK at this time.? NO – If the idle speed is less than 680 rpm, go to step 3; if it’s 780 rpm or higher, go to step 4. 3. Disconnect the idle air control (IAC) valve 3P connector. Does the engine speed increase or fluctuate? YES – Adjust the idle speed. If the idle will not adjust properly, clean the passage in the throttle body, and then adjust the idle.? NO – Replace the IAC valve.? 4. Turn the ignition switch OFF. 5. Remove the intake air duct from the throttle body. 6. Start the engine and let it idle. 7. Put your finger on the lower port (A) in the throttle body. Does the engine speed drop below 780 rpm? YES – Adjust the idle speed. If the idle will not adjust properly, replace the IAC valve, and then adjust the idle.? NO – With the throttle valve completely closed, check for vacuum leaks, and repair as necessary.?
Related entry: H3 Hummer LOUD VIBRATING SOUND IDLING
, tool for programming nissan idle
, how to adjust idle speed on 2005 camry
, 02 hyundai elantra erratic idle
, how to adjust idle control on 1994 geo metro
, how to ajust idle in a 2007 toyota tacoma
, how to increase tocometer camry 1998
, how to set idle on RX8 mazda
, idle air control valve on 01 hyundai sonata 2 4 engine
, idle air mixture screw 1994 ford laser
Filed Under (GM) by admin on 03-11-2010
Located on the throttle body, the Idle Speed Control (ISC) valve opens the air bypass passage when the solenoid is ON and closes it when the solenoid is “OFF.” The ECM turns the ISC solenoid ON and OFF at a constant cycle of 20 times per second. It controls the bypass air flow by making “ON” time one cycle shorter or longer depending on conditions. In this system, the ECM controls the ISC solenoid valve according to the signals from various sensors and switches to control the bypass air flow which plays the following three roles as required by certain circumstances. IDLE-UP AIR FLOW When head lights & other lights, heater fan, rear defogger (if equipped) or air conditioner (if equipped) are operating, and/or the automatic transmission is in a range other than PARK or NEUTRAL, and/or the vehicle is at high altitudes, higher than 8,200 ft or 2,500 m, the bypass air is supplied to stabilize the engine idle speed. How much air is supplied varies depending on the load. When head lights and other lights are ON, the idle speed rises only a little higher than the normal specified idle speed (920 rpm). AFTER START AIR FLOW When and after the engine is started, the bypass air is supplied to prevent the engine from stopping when the throttle opener is OFF and to improve the engine performance at its start. How much bypass air is supplied varies depending on the engine cooling water temperature and it decreases as time passes when engine is cool. When engine is hot and 15 seconds have passed after engine starts, a given amount of bypass air is supplied until either the idle switch is turned OFF from ON once or engine speed exceeds 1,500 rpm once. DASHPOT AIR FLOW A sudden change in the throttle valve opening (especially when decelerating) causes the air/fuel mixture ratio to change suddenly. To compensate for this condition, the bypass air flow will be increased or decreased depending on condition. By increasing or decreasing the air, the air/fuel mixture ratio is changed gradually and dashpot effect is obtained. The air is increased when throttle is opened and decreased when the throttle is closed.
Related entry: how to replace manual trans to an aotumatic in a 93 geo tracker
, 1996 geo tracker repair manual free
, automotix net/ part diagram 1996 geo tracker
, caja de fusibles tracker
, como poner cadena de tiempo chevy tracker 2 0
, geo tracker 95 manual
, service manual 1996 geo tracker 1 6
Filed Under (Subaru) by admin on 02-01-2011
Removal of Factory Intake 1. 2. Turn the ignition OFF and disconnect the vehicle’s negative battery cable. Loosen and remove the two bolts that secure the air inlet duct to the radiator core support, then remove the air inlet duct. Loosen the clamps at the air cleaner assembly and turbo inlet tube, then remove the stock intake tube. Loosen and remove the two bolts that secure the air cleaner assembly. Pull upwards to remove the air cleaner assembly. Using the bolt removed to secure the ABS control bracket. Loosen and remove the two screws that secure the mass air sensor to the air cleaner assembly, then remove the mass air sensor. Raise the vehicle and support with the jack stands, then remove the front passenger side tire. Remove the five plastic push/screw clips that secure the inner wheel house valance. Remove the 6 screw in push clips that secure the air duct to the lower valance, then remove the air duct. Remove the two remaining push clips that secure the lower valance, then pull the valance down. From inside the apron, remove the push clip that secures the apron to the upper fender. Remove the hex nut that secures the air intake resonator to the inner fender. Loosen and remove the second hex nut that secures the air intake resonator from underneath the vehicle. Remove the air intake resonator. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Install of Intake 16. Install the reducer and clamps onto the turbo and secure. 17. Loosen and remove the hex bolt on the cam cover. 18. Using the provided allen bolts, secure the mass air sensor into the adapter on the intake tube. 19. Using the allen bolts, secure the mass air sensor into the adapter on the intake tube. 20. Slide the intake tube into the reducer and secure the mass air sensor into the adapter on the intake tube. 21. Tighten the clamp on the intake tube. 22. Install the reducer and clamps onto the intake tube. 23. From underneath the vehicle loosen and remove the hex nut that secures the ABS pump to the inner fender. 24. Slide the cold air tube intake tube from underneath the vehicle into the hole in the inner fender, then line up the bracket with the ABS bolts, and tighten with the nut remove. 25. Slide the reducer onto the cold air intake tube. 26. Install the Bomz Filtercharger onto the cold air intake tube and secure with clamp. 27. Reverse the removal process for the plastic wheelhouse valance and air duct with the stock push clips. 28. Reconnect the mass air sensor electrical connection. 29. Reconnect the negative battery cable and double check to make sure everything is tight before starting the vehicle. Resetting the ECU This is to be completed at your own risk. This procedure will reset the computer so that it may “learn” of your new intake. We are not to be held liable for any mishaps that you may occur while completing this process. • • Disconnect the Negative battery cable for 5 minutes. Reconnect the battery cable and false panel cover.
Related entry: 2002dodge intrepidintake removal
, how to change intake manifold gasket on elantra
, intake manifold torque specs for 2002 chevy impala with 3 8 engine
, Diagram of a 200 Oldsmobile Intrigue Throttle Body
, how to relearn a mass air flow sensor
, how many plenum gaskets for 2005 avalon
, gm 3 8 intake torque sequence
, find air flow metre on mercedes w203
, diagram of the motor ls 400 lexus 1992 intake
, how to remive air flow boot on x5 2004 bmw
Filed Under (Ford) by admin on 27-04-2010
FORD: 2000-2003 TAURUS 2002 THUNDERBIRD 2000-2003 EXPLORER, RANGER 2001-2003 EXPLORER SPORT TRAC, EXPLORER SPORT
LINCOLN: 2000-2002 LS MERCURY: 2000-2003 SABLE, MOUNTAINEER ISSUE
Some vehicles, may exhibit drivability conditions.
These may include: • No start • Difficult to start • Stall • Low idle • Rough • High idle • Hesitation/surge while accelerating or at steady speed These conditions may be intermittent with no Diagnostic Trouble Codes (DTC) and no Malfunction Indicator Lamp (MIL). In some cases DTC and MIL may be evident. ACTION Trouble cannot be identified with 95% of returned Idle Air Control (IAC) valves. The following procedure is supplemental information to normal diagnostics to facilitate accurate identification of malfunctioning valves. These symptoms would include engine stall, hard start, crank/no start, idling problems, and Idle Speed Control System related DTC’s. If the service writer uses the attached worksheet (Figure 2) for all drivability concerns including stalls it will assist the technician making a correct repair the first time.