location of the coolant fan sensor for the 2002 Hyundai Sonata


You are searching repair manual in PDF format about location of the coolant fan sensor for the 2002 Hyundai Sonata use another keyword for search another post or files



  location of the coolant fan sensor for the 2002 Hyundai Sonata Direct Download speed 5787 Kb/s

  location of the coolant fan sensor for the 2002 Hyundai Sonata Full Version speed 6767 Kb/s




2000-2002 Pontiac Grand Prix Low Engine Coolant Level Indicator Always on (Diagnose Low Coolant Level System

0

Filed Under (Pontiac) by admin on 17-01-2011

download
Subject: Models: Low Engine Coolant Level Indicator Always On (Diagnose Low Coolant Level System Operation/Check Sensor for Oil Contamination) 2000-2002 Buick Century, Regal 2000-2001 Chevrolet Lumina 2000-2002 Chevrolet Impala, Monte Carlo 2000-2002 Pontiac Grand Prix 2000-2002 Oldsmobile Intrigue Condition Some customers may comment that the low engine coolant level indicator is always illuminated. Cause The cause of this condition may be due to engine oil contaminating the coolant. Possible sources of oil contamination are internal engine leaks, improper service procedures, or the addition of some types of anti-leak additives to the cooling system. Once in the coolant, the oil leaves deposits on the level sensor creating an insulating film. This film results in a false activation of the coolant level indicator. Correction Diagnose low coolant level system operation and check the sensor for oil contamination using the procedure listed below. Important: No coolant supplements should be used in GM cooling systems, other than what is approved and recommended by GM. The use of “aftermarket” over-the-counter sealing and cooling supplements may affect the operation of the low coolant level sensor. Discoloration of the coolant recovery bottle is normal and does not necessarily indicate that coolant contamination is present. Flush cooling system only when instructed by this bulletin. 1. Verify that the coolant is at proper level in the radiator and the coolant recovery bottle. If the coolant is low, add proper amount of 50/50 water and DEX-COOL® mixture. If the low coolant light operates properly, diagnose the cooling system for loss of coolant as outlined in SI. DO NOT proceed further with this bulletin. 2. Remove the low coolant level sensor. Refer to Coolant Level Module Replacement in the Engine Cooling sub-section. 3. With the key on, the engine off and the coolant level sensor disconnected from the vehicle wiring harness, observe the low coolant light: • Light is on — Chassis wiring or instrument cluster concern. Follow the appropriate diagnostic information in SI. • Light is out — Proceed to Step 4.

Related entry:

2000 pont 2 2 eng coolant circulation, replace coolant sensor 2000 pontiac, coolant low sensor is on bmw2003 x5 4 4, how to drain and fill 2000 mercury grand, 2002 ford explorer low pressure port, 2002 chevy venture hoses, LOCATING THE LOWER AC PORT ON A 2004 MAZDA 6, time and labor charge to replace coolant temperature sensor on a 2003 cts?, 2002 pontiac grand prix condensation line drain plugged, 2000 pontiac montana 3 4 temperature sensor diagram,

2002 Kia Spectra SENDING UNITS & SENSORS LOCATION

0

Filed Under (KIA) by admin on 13-06-2010

download
Air Quality Sensor At center front of engine compartment. Camshaft Position Sensor On rear of cylinder head. See Fig. 1 . Chassis Acceleration Sensor At right rear side of engine compartment. Crankshaft Position Sensor On left front side of transaxle. See Fig. 1 . Engine Coolant Temperature On top rear of engine, near thermostat. See Fig. 1 . Sensor Fuel Tank Unit On top of fuel tank, below rear seat cushion. Hot Film Airflow Sensor On end of air intake hose, at air cleaner housing. See Fig. 1 . Knock Sensor Near center rear of engine compartment, on intake manifold support bracket. O2 Sensor (Down) On front exhaust pipe, downstream of warm-up TWC converter. O2 Sensor (Up) On exhaust manifold, upstream of warm-up TWC converter. Speed Sensor On top of transaxle. Thermocon Behind glove box, on HVAC assembly. See Fig. 2 . Throttle Position Sensor On throttle body. See Fig. 1 . Turbine Sensor (A/T) On top rear of transaxle. Wheel Speed Sensor (Left Front) Attached to left front hub spindle. Wheel Speed Sensor (Left Rear) Attached to left rear hub spindle. Wheel Speed Sensor (Right Attached to right front hub spindle. Front) Wheel Speed Sensor (Right Rear) Attached to right rear hub spindle.

Related entry:

2001 grand am Coolant Level Module Replacement, 2001 pontiac grand am map sensor replacement, 2002 kia sportage where is the oil pressure sending unit, 2006 nissan front cash zone sensor location, 97x ambient tem camshaft position sensor location, can i see a diagram of installing the map sensor on the buick rainier2004, how to install a map sensor on a buick rainer, map sensor location 2001 kia, o2 sensor fuse location 97 chevy Tahoe,

1995 Ford Mustang Camshaft Position (CMP) Sensor Removal Installation

0

Filed Under (Ford) by admin on 08-02-2011

download
1. Disconnect battery ground cable (14301) . 2. Disconnect fuel charging wiring (9D930) from distributor stator (12A112) (camshaft position sensor). 3. Remove stator camshaft position sensor retaining screws and distributor stator (camshaft position sensor) from camshaft position sensor housing. 4. If removing camshaft position sensor housing from the engine front cover (6019) , proceed with Removal Step 5. If camshaft position sensor housing is not being removed, proceed to Installation Step 6. 5. CAUTION: Before proceeding with this procedure, set cylinder No. 1 to 26 degrees After Top Dead Center (ATDC) of the compression stroke. Then note the position of the stator (camshaft position sensor) electrical connector. The installation procedure requires that the connector be located in the same position. Remove retaining bolt and hold-down clamp (12270) . 6. NOTE: The oil pump intermediate shaft (6A618) should be removed with the camshaft position sensor housing. Remove camshaft position sensor housing from engine front cover . Installation 1. CAUTION: If the replacement distributor stator (camshaft position sensor) does not contain a plastic locator cover tool, a special service tool such as Syncro Positioning Tool T89P-12200-A must be obtained prior to installation of the replacement distributor stator (camshaft position sensor). Failure to follow this procedure will result in improper stator (camshaft position sensor) alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage. If the plastic locator cover tool is not attached to the replacement distributor stator (camshaft position sensor), attach Syncro Positioning Tool T89P-12200-A as follows: a. Engage camshaft position sensor housing vane into the radial slot of the tool. b. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing. The cover tool should be square and in contact with entire top surface of camshaft position sensor housing. 2. Transfer oil pump intermediate shaft from old camshaft position sensor housing to replacement camshaft position sensor housing. 3. CAUTION: If stator (camshaft position sensor) electrical connector is not positioned properly (for example, contacting the A/C compressor bracket), DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1. Install camshaft position sensor housing so that drive gear engagement occurs when arrow on locator tool is pointed approximately 30 degrees counterclockwise from the front face of the cylinder block (6010) . This step will locate stator (camshaft position sensor) electrical connector in the pre-removal position. 4. Install hold-down clamp and retaining bolt and tighten bolt to 20-30 Nm (15-22 lb-ft). 5. Remove Syncro Positioning Tool T89P-12200-A. 6. CAUTION: If stator (camshaft position sensor) electrical connector is not positioned properly (for example, contacting the A/C compressor bracket), DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1. Install distributor stator (camshaft position sensor) and retaining screws. Tighten screws to 2.5-3.5 Nm (22-31 lb-in). 7. Connect fuel charging wiring connector to distributor stator (camshaft position sensor). 8. Connect battery ground cable .

Related entry:

how to change map sensor 2004 Trailblazer, 07 fusion evap temp loca, 2009 nissan micra crankshaft sensor relacement, cadillac srx 3 6 cam sensor location, tss sensor for mercury sable 2008, 2002 ls evaporator discharge temp sensor location, jaguaR- X-Type knock sensor removal, j36796, 2004 beetle thrust switch sensor, 2004 freestar nock sensor,

1998 Ford Windstar Camshaft Position (CMP) Sensor REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 17-02-2011

download
CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126) , set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Then note the position of the camshaft position sensor electrical connector. The installation procedure requires the connector be located in the same position. Removal 1. Disconnect battery ground cable (14301). Refer to Section 14-01. 2. Disconnect fuel charging wiring connector from camshaft position sensor. 3. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing. 4. If removing camshaft position sensor housing from the cylinder block (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to Step 6 of the installation procedures. 5. Remove hold-down clamp (12270) (bolt and washer assembly). 6. NOTE: Remove the oil pump intermediate shaft (6A618) with the camshaft position sensor housing. Remove camshaft position sensor housing from cylinder block. Installation 1. CAUTION: If the replacement camshaft position sensor housing does not contain a plastic locator cover tool, a special service tool must be obtained prior to installation of the replacement camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the ignition fuel system being out of time with the engine, possibly causing engine damage. NOTE: For 3.0L engines, use Syncro Positioning Tool 303-589. For 3.8L engines, use Syncro Positioning Tool 303-562 (T96T-12200-A). If the plastic locator cover tool is not attached to the replacement camshaft position sensor housing, attach syncro positioning tool as follows: a. Engage camshaft position sensor housing vane into the radial slot of the tool. b. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing. 2. Transfer oil pump intermediate shaft from old camshaft position sensor housing to replacement camshaft position sensor housing. 3. Install camshaft position sensor housing so drive gear engagement occurs when arrow on syncro positioning tool is pointed approximately as shown in the illustrations. This step will locate camshaft position sensor electrical connector in the pre-removal position. 4. Install hold-down clamp (washer and bolt assembly) and tighten bolt to 20-30 Nm (15-22 lb-ft). 5. Remove syncro positioning tool. 6. CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1. Install camshaft position sensor and retaining screws. On 3.0L engine, tighten screws to 2.5-3.5 Nm (23-30 lb-in). On 3.8L engine, tighten screws to 4.5-7 Nm (40-61 lb-in). 7. Connect fuel charging wiring connector to camshaft position sensor. 8. Connect battery ground cable. Refer to Section 14-01. Camshaft Position Sensor—3.0L Engine

Related entry:

www 1999 ford f150 4 6 where is the camsensor located com, service manual for 1997 mazda 121 soho, j39194-b tool, how to remove cam sensor on 1998 ford windstar, how to fix a throttle sencer for ford windstar, honda accord 2000 how to test iac, google2001 santa fe camshaft position sensor, CAMSHAFT SPROCKET 2000 FORD ESCORTS ZX2 2 0L, c-4829 tool, 2000 ford escort camshaft sprocket,

2003 Chevy TrailBlazer Radiator Cooling Fan: Description and Operation

0

Filed Under (Chevrolet) by admin on 29-08-2010

download
Cooling Fan Control The purpose of the Electro-Viscous (EV) fan clutch is to maintain powertrain cooling requirements. The Powertrain Control Module (PCM) monitors the following sensors to regulate the fan speed; – Engine coolant temperature sensor – A/C refrigerant pressure sensor – Vehicle speed sensor – Intake air temperature sensor – Transmission fluid temperature sensor – Ambient air temperature sensor The PCM controls the electro-viscous fan clutch engagement. The PCM regulates a 12-volt pulse width modulated signal (PWM) to the cooling fan relay. The PWM signal determines the ON time of the relay. As the commanded state of the fan clutch increases, so does the ON time of the relay. This ON time directly effects the amount of time the solenoid, which is internal to the fan clutch, is energized. When the solenoid in the fan clutch is energized, it opens the spring loaded valve and allows fluid to flow from the storage chamber to the fluid coupling of the cooling fan clutch, increasing the fan speed. When the solenoid is de-energized, the spring loaded valve closes, and blocks the path of the fluid to the fluid coupling of the fan clutch, reducing fan speed. The fan has the ability to create a feedback signal, so the PCM has an actual fan speed input. This is done with a hall effect sensor internal to the fan clutch. The PCM supplies a 5-volt reference and a low reference to the hall effect sensor. The hall effect sensor returns a signal pulse through the cooling fan speed signal circuit in response to the reluctor track passing by the magnetic field of the hall effect sensor. The PCM commands the cooling fan to 100% under the following conditions: – Engine coolant temperature exceeds approximately 129°C (264°F). – The transmission oil temperature exceeds approximately 151°C (304°F). – A/C refrigerant pressure exceeds 1655 kPa (240 psi). – When certain DTC’s set. These include P0116, P0117, P0118, P0125, P1481, P1482, and P1484.

Related entry:

Codigos de trailblazer 2003 p1481, e46 viscous coupler removal, how to undo a viscous fan VW LT3535, P1482 cooling fan spped sensor circuit, p1482 trailblazer, replacement of Vw Lt Viscous Fan, senzor hall,