location of vapor canister shutoff valve on 2006 hyundai sonata


You are searching repair manual in PDF format about location of vapor canister shutoff valve on 2006 hyundai sonata use another keyword for search another post or files



  location of vapor canister shutoff valve on 2006 hyundai sonata Direct Download speed 5787 Kb/s

  location of vapor canister shutoff valve on 2006 hyundai sonata Full Version speed 6767 Kb/s




2002 Hyundai Accent 1.6L, Vin C 2003 Hyundai Accent GS 1.5L Difficulty filling the gas tank The pump keeps clicking off

0

Filed Under (Hyundai) by admin on 25-04-2010

download
1. Disconnect the vapor line at the charcoal canister that comes from the liquid vapor separator and goes to the charcoal canister. See if the fuel tank can be easily filled then. 2. If the fuel tank can easily be filled with the vapor line removed from the charcoal canister, reconnect the vapor line and remove the other lines from the charcoal canister and see if the fuel tank can be easily filled. 3. If the fuel tank is once again difficult to fill, replace the charcoal canister. 4. If disconnecting the vapor line at the charcoal canister does NOT make the fuel tank easy to fill, then disconnect the vapor line from the liquid vapor separator at
the fuel tank in case the vapor line is plugged/restricted. Charcoal Canister Liquid Vapor Separator Vapor Line Fuel vapors are directed to the canister from the ORVR fill vent valve in the gas tank through the liquid vapor separator and to the canister. The metal tube that
loops up by the filler neck is part of the vapor line to the canister.

Related entry:

yhs-looksafe_ds_trans, location of charcoal canister on 2003 ford escape v6, where is the EVAP canister for a 2002 Ford Crown Victoria located, firing order 2011 hyundai accent gls, 2009 hyundai accent 1 6 firing order, 2006 chevrolet silverado evap plugged up what to do, hyundia2007 sanafa diagram evap control system, charcoal canister on 2003 ford escape v6, hyundai 2000 accent gas vacuum canister orbr, hyundai accent headlight adjustment,

2004 Honda Accord EVAP Canister Vent Shut Valve Stuck Closed Malfunction

0

Filed Under (Honda) by admin on 05-11-2010

download
1. 2. 3. 4. Turn the ignition switch ON (II). Clear the DTC with the HDS. Remove the fuel fill cap for 5 seconds , then install it. Start the engine. Hold the engine speed at 3,000 rpm with no load (in Park or neutral) until the radiator fan comes on, then let it idle. Monitor the OBD STATUS for DTC P2422 in the DTCs MENU with the HDS. Does the screen indicate FAILED? YES – Go to step 6. NO – If the screen indicates PASSED, intermittent failure, system is OK at this time. Check for a poor connection or loose terminals at the EVAP canister vent shut valve and ECM/PCM. If the screen indicates NOT COMPLETED, go to step 2 and recheck. Clear the DTC with the HDS. Remove the EVAP canister vent shut valve from the EVAP canister. Connect the 2P connector to the EVAP canister vent shut valve. Turn the ignition switch ON (II). Do the EVAP CVS ON in the INSPECTION MENU with the HDS. 5. 6. 7. 8. 9. 10. 11. Check the EVAP canister vent shut valve (A) operation. Does the valve operate? YES – Check for a blockage in the EVAP canister, then install the EVAP canister vent shut valve, and go to step 14. NO – Go to step 12. 12. Turn the ignition switch OFF. 13. Replace the EVAP canister vent shut valve. 14. Turn the ignition switch ON (II). 15. Reset the ECM/PCM with the HDS. 16. Do the ECM/PCM idle learn procedure. 17. Turn the ignition switch OFF. 18. Remove the fuel fill cap for 5 seconds , then install it. 19. Start the engine. Hold the engine speed at 3,000 rpm with no load (in Park or neutral) until the radiator fan comes on, then let it idle. 20. Check for Temporary DTCs or DTCs with the HDS. Are any Temporary DTCs or DTCs indicated? YES – If DTC P2422 is indicated, check for poor connections or loose terminals at the FTP sensor or the EVAP canister vent shut valve and the ECM/PCM, then go to step 1. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTC’s troubleshooting. NO – Go to step 21. 21. Monitor the OBD STATUS for DTC P2422 in the DTCs MENU with the HDS. Does the screen indicate PASSED? YES – Troubleshooting is complete. NO – If the screen indicates FAILED, check for poor connections or loose terminals at the FTP sensor or the EVAP canister vent shut valve and the ECM/PCM, then go to step 1. If the screen indicates NOT COMPLETED, go to step 16 and recheck.

Related entry:

2002 kia sportage evap sstem check, how to replace chevy 2005 tahoe vent solenoid valve replacement, repair evap lines tahoe cracked, evap 97 jimmy, how to clean an evap canister on a chevy tracker, fuel system emission diagram 2004 trail blazer, how to change evap vent valve on pontiac sunfire, how much to replace evap canister in 2006 F150 v8 5 4, fixing an evap sensor on a 1998 oldsmobile cutlas, how to replace purge value 2000 ponaic sunfire,

2000 Buick LeSabre Canister Vent Valve Service and Repair REMOVAL INSTALLATION PROCEDURE

0

Filed Under (Buick) by admin on 08-07-2010

download
REMOVAL PROCEDURE 1. Turn OFF the ignition. CAUTION: Refer to Hoist Caution in Service Precautions . 2. Raise the vehicle. Refer to Vehicle Lifting. 3. Bend the retaining tab for the EVAP canister vent valve. 4. Remove the valve from the bracket. 5. Disconnect the electrical connector from the EVAP canister vent valve. 6. Loosen the vent hose clamp and remove the vent hose from the EVAP vent valve. 7. Remove the EVAP canister vent valve from the vehicle. INSTALLATION PROCEDURE 1. Connect the vent hose to the EVAP canister vent valve and tighten the hose clamp. 2. Connect the electrical connector to the EVAP canister vent valve. 3. Install the EVAP canister vent valve to the bracket. 4. Bend the retaining tab for the EVAP canister vent valve. 5. Lower the vehicle

Related entry:

2000 lincoln canister vent valvesolenoid, 06 ZEPHYR DASH DEFROST VENT LOOSE, how to change deforst vent on 2008 ford fusion dash board, how to fix mkz dashboard near defrost vent, how to install a canister/vent valve assembly in a 2009 Chv HHR, pics of fuel tank vacuum relief valve for 2001 hyundai sonata, repairing the vent control on a 2010 buick enclaude, were is charcoal canister on 04 endeavor, where is the purge solenoid 2004 mitsubishi endeavor, gas tank venting system mercury grand marquis,

1995 Ford Windstar VALVE CLEARANCE ADJUSTMENT

0

Filed Under (Ford) by admin on 17-03-2011

download
NOTE: Hydraulic valve lifters are used; no valve adjustment is required. When valve and/or valve seat is machined, valve clearance is reduced and may cause improper valve operation. Different length push rods are available for correcting clearance. Valve lifter must be collapsed to check valve clearance. 1. With valve cover removed, position piston No. 1 at TDC of compression stroke. Completely collapse cylinder No. 1 intake valve lifter and hold valve lifter collapsed. Using feeler gauge, measure clearance between rocker arm and valve stem. 2. Clearance should be within specification. Refer to COLLAPSED VALVE LIFTER CLEARANCE table. Replace push rod, if necessary, to obtain correct clearance. 3. Position crankshaft as specified. See, in this article, VALVE CLEARANCE CHECKING SEQUENCE table, and check appropriate valves. Replace push rods if clearance is not within specification. 4. If push rod(s) is replaced, ensure corresponding cylinder piston is below TDC. It will be necessary to loosen or remove rocker arm to replace push rod. CAUTION: DO NOT operate or crank engine after installing push rod until valve lifter has leaked down to normal operating position. COLLAPSED VALVE LIFTER CLEARANCE

Related entry:

1995 3 0 ford valve height, izusu 4jg2 valve clearance, what is the compression reading at cylinders on 2002 1290cc Ford Fiesta, suzuki vitara 8 valve timing, transmission solenoid in vw jetta 2006, what solenoid is used on 2nd and 3rd gear vw jetta mk5 vavle body transmission, location of a purge valve on a 2011 Hyundai Tucson, location of purge valve for 2011 hyundai tucson, mazda 626 1997 bleeding hydraulic lifters, Mazda V6 DOHC 24 Valve rough idle,

1992 Suzuki Swift VALVE CLEARANCE ADJUSTMENT

0

Filed Under (Suzuki) by admin on 26-05-2011

download
NOTE: Samurai & Sidekick 1) Remove rocker cover. Rotate crankshaft until zero degree (TDC) timing mark of timing belt cover is in line with timing mark on crankshaft pulley. 2) Cylinder No. 1 should be at TDC on compression stroke. Remove distributor cap, and ensure rotor is pointed upward at distributor hold-down bolt and to No. 1 terminal of distributor cap. If not as described, rotate crankshaft 360 degrees. 3) Measure valve clearance between adjustment screw and valve stem using thickness gauge. Check intake valve clearance of cylinders No. 1 and 2 and exhaust valve clearance of cylinders No. 1 and 3. 4) Turn crankshaft one complete revolution (360 degrees). Check intake valve clearance of cylinders No. 3 and 4 and exhaust valve clearance of cylinders No. 2 and 4. Ensure clearance is within specification. See VALVE CLEARANCE SPECIFICATIONS table. 5) If clearance adjustment is necessary, loosen lock nut and turn adjusting screw. After adjusting clearance, tighten adjusting Swift DOHC uses hydraulic lifters. Adjustment is not required. screw lock nut to 11-14 ft. lbs. (15-19 N.m) on Samurai or 90-108 INCH lbs. (10-13 N.m) on Sidekick. On all models, recheck clearance. VALVE CLEARANCE SPECIFICATIONS TABLE ¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡ Application SOHC Engines Samurai, Sidekick 8-Valve TBI & Swift (1) Engine Cold Exhaust ……………………. .006-.008 (.15-.20) Intake …………………….. .005-.007 (.13-.17) Engine Hot Exhaust ……………………. .010-.012 (.25-.30) Intake …………………….. .009-.011 (.23-.27) Sidekick 16-Valve PFI Engine Cold Exhaust & Intake ………….. .0031-.0047 (.08-.12) Engine Hot Exhaust & Intake ………….. .0047-.0063 (.12-.16) DOHC Engine Swift (1) …………………………………. (2) (1) – Swift is available with 1.3L DOHC and SOHC engines. (2) – Hydraulic valve lash adjusters are used. Adjustment is not required. ¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡ Swift SOHC 1) Remove rocker cover. Remove right side inner fender apron extension to enable timing marks to be seen. Align crankshaft pulley timing mark with TDC mark on timing belt cover. 2) Remove distributor cap. Ensure rotor is pointing upward toward distributor hold-down bolt and to No. 1 terminal of distributor cap. If not as described, rotate crankshaft 360 degrees. 3) Measure valve clearance between adjustment screw and valve stem using thickness gauge. Check intake valve clearance of cylinders No. 1 and 2 and exhaust valve clearance of cylinders No. 1 and 3. Turn crankshaft one complete revolution (360 degrees). Check intake valve clearance of cylinders No. 3 and 4 and exhaust valve clearance of cylinders No. 2 and 4. 4) Ensure clearance is within specification. See VALVE CLEARANCE SPECIFICATIONS table. If clearance adjustment is necessary, loosen lock nut and turn adjusting screw. Hold adjusting screw while tightening lock nut to 11-14 ft. lbs. (15-19 N.m). Recheck clearance. In. (mm)

Related entry:

clearence valves of engine 4m40 mitsubishi, valve adjustment on ford 2 3, 1fz camshaft removal, valve clearance setting l200 triton, valve adjustment tool for landcruiser, 2008 xl7 luxury purge air solinoid, how to adjust valves on 2000 toyota corrola, daihatsu rock lifter adjustment, valve adjustment on 2003 nissan altima 2 5 engine, diagram of adjusting the handbrake on a holden rodeo ra,