man tga valve adjusting


You are searching repair manual in PDF format about man tga valve adjusting use another keyword for search another post or files



  man tga valve adjusting Direct Download speed 5787 Kb/s

  man tga valve adjusting Full Version speed 6767 Kb/s




1992 Suzuki Swift VALVE CLEARANCE ADJUSTMENT

0

Filed Under (Suzuki) by admin on 26-05-2011

download
NOTE: Samurai & Sidekick 1) Remove rocker cover. Rotate crankshaft until zero degree (TDC) timing mark of timing belt cover is in line with timing mark on crankshaft pulley. 2) Cylinder No. 1 should be at TDC on compression stroke. Remove distributor cap, and ensure rotor is pointed upward at distributor hold-down bolt and to No. 1 terminal of distributor cap. If not as described, rotate crankshaft 360 degrees. 3) Measure valve clearance between adjustment screw and valve stem using thickness gauge. Check intake valve clearance of cylinders No. 1 and 2 and exhaust valve clearance of cylinders No. 1 and 3. 4) Turn crankshaft one complete revolution (360 degrees). Check intake valve clearance of cylinders No. 3 and 4 and exhaust valve clearance of cylinders No. 2 and 4. Ensure clearance is within specification. See VALVE CLEARANCE SPECIFICATIONS table. 5) If clearance adjustment is necessary, loosen lock nut and turn adjusting screw. After adjusting clearance, tighten adjusting Swift DOHC uses hydraulic lifters. Adjustment is not required. screw lock nut to 11-14 ft. lbs. (15-19 N.m) on Samurai or 90-108 INCH lbs. (10-13 N.m) on Sidekick. On all models, recheck clearance. VALVE CLEARANCE SPECIFICATIONS TABLE ¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡ Application SOHC Engines Samurai, Sidekick 8-Valve TBI & Swift (1) Engine Cold Exhaust ……………………. .006-.008 (.15-.20) Intake …………………….. .005-.007 (.13-.17) Engine Hot Exhaust ……………………. .010-.012 (.25-.30) Intake …………………….. .009-.011 (.23-.27) Sidekick 16-Valve PFI Engine Cold Exhaust & Intake ………….. .0031-.0047 (.08-.12) Engine Hot Exhaust & Intake ………….. .0047-.0063 (.12-.16) DOHC Engine Swift (1) …………………………………. (2) (1) – Swift is available with 1.3L DOHC and SOHC engines. (2) – Hydraulic valve lash adjusters are used. Adjustment is not required. ¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡ Swift SOHC 1) Remove rocker cover. Remove right side inner fender apron extension to enable timing marks to be seen. Align crankshaft pulley timing mark with TDC mark on timing belt cover. 2) Remove distributor cap. Ensure rotor is pointing upward toward distributor hold-down bolt and to No. 1 terminal of distributor cap. If not as described, rotate crankshaft 360 degrees. 3) Measure valve clearance between adjustment screw and valve stem using thickness gauge. Check intake valve clearance of cylinders No. 1 and 2 and exhaust valve clearance of cylinders No. 1 and 3. Turn crankshaft one complete revolution (360 degrees). Check intake valve clearance of cylinders No. 3 and 4 and exhaust valve clearance of cylinders No. 2 and 4. 4) Ensure clearance is within specification. See VALVE CLEARANCE SPECIFICATIONS table. If clearance adjustment is necessary, loosen lock nut and turn adjusting screw. Hold adjusting screw while tightening lock nut to 11-14 ft. lbs. (15-19 N.m). Recheck clearance. In. (mm)

Related entry:

sequent of tighining valve cover gasket nuts of 2000 bmw z3, 2001 chevy malibu valve adjustment 6 cylander, valve adjustment 1992 toyota corolla, how to adjust headlights on chevy avalanche, 96 3 8l valve cover removal, 2003 miata vvt 10 degrees out, renault clio 1 4 16 valve idler pulley dimension, purge sensor location 2008 suzuki xl7, valve adjustment on 2000 ford courier 2 5 turbo, valve adjustment 01 forester,

1995 Ford Windstar VALVE CLEARANCE ADJUSTMENT

0

Filed Under (Ford) by admin on 17-03-2011

download
NOTE: Hydraulic valve lifters are used; no valve adjustment is required. When valve and/or valve seat is machined, valve clearance is reduced and may cause improper valve operation. Different length push rods are available for correcting clearance. Valve lifter must be collapsed to check valve clearance. 1. With valve cover removed, position piston No. 1 at TDC of compression stroke. Completely collapse cylinder No. 1 intake valve lifter and hold valve lifter collapsed. Using feeler gauge, measure clearance between rocker arm and valve stem. 2. Clearance should be within specification. Refer to COLLAPSED VALVE LIFTER CLEARANCE table. Replace push rod, if necessary, to obtain correct clearance. 3. Position crankshaft as specified. See, in this article, VALVE CLEARANCE CHECKING SEQUENCE table, and check appropriate valves. Replace push rods if clearance is not within specification. 4. If push rod(s) is replaced, ensure corresponding cylinder piston is below TDC. It will be necessary to loosen or remove rocker arm to replace push rod. CAUTION: DO NOT operate or crank engine after installing push rod until valve lifter has leaked down to normal operating position. COLLAPSED VALVE LIFTER CLEARANCE

Related entry:

remove rear expansion valve on 2008 yokon, changing valve lifters from 2000 toyota corolla le, 02 camry how to replace expansion valve, where is the expansion valve in suburban 1500, 2000 gmc jimmy cooling system bleed valve, exspansion valve 2004 camry replacement, 2006 jetta transmission solenoids, valve clearance adjustment 4age, 2002 chevy malibu expansion balve replacement, 2005 toyota sienna ac expansion valve replacement,

1996 Ford Taurus valve body Removal and Installation

0

Filed Under (Ford) by admin on 16-10-2010

download
REMOVAL NOTE: The oil pump and valve body are removed as an assembly. 1. Disconnect battery ground cable, then remove battery, battery tray, and remote air cleaner. 2. Position supply hoses, vacuum hoses, and wiring away from pump and valve body cover. 3. Remove shift lever. 4. On models equipped with Anti-lock Brake System (ABS) , remove splash shield cover, then disconnect brake reservoir hose and cap to prevent contamination. 5. On all models, remove EGR bracket attaching bolts, then install lifting eye. 6. Remove throttle body bracket attaching bolt, install lifting eye, then using suitable equipment support engine. 7. Remove lefthand transaxle mount. 8. Remove transaxle side pan upper attaching bolts. 9. Raise and support vehicle. 10. Remove lefthand front wheel and tire assembly. 11. Remove inner fender cover and position aside, then disconnect ride height sensor. 12. Remove rear transaxle mount attaching bolt. 13. Loosen but do not remove two lefthand subframe attaching bolts. 14. Remove two engine support mount attaching bolts. 15. Remove four lefthand engine support attaching bolts, then remove the engine support. 16. Position suitable drain pan, then remove remaining transaxle side pan attaching bolts and remove pan. 17. Using suitable screwdriver, place manual shift shaft in Park position. 18. Disconnect upper bulkhead electrical connector wiring retainer clip from valve body. 19. Disconnect electrical connectors. Oil Pump And Valve Body Bolt Removal 20. Remove valve body attaching bolts, then disengage linkage and remove valve body. NOTE: Do not remove oil pump cover attaching bolts. INSTALLATION 1. Install new pump and valve body to chain cover gasket. 2. Slide pump and valve body onto pump shaft. 3. Rotate pump and valve body assembly toward dash panel, then engage manual valve link with manual valve. 4. Slightly rotate pump and valve body assembly to engage oil pump shaft splines with oil pump rotor splines. Valve body should slide flush with chain cover. A suitable 7/8 inch deep well socket on crankshaft pulley may be required for complete engagement. 5. On models less anti-skid, if engagement is not as indicated in step 4, proceed as follows: a. Remove manual valve from valve body. b. Rotate assembly to allow full engagement, up to 360° . c. After full engagement, return assembly to installed position, then install manual valve.

Related entry:

4l60e valve body bolt location, 722 3 transmission USED valve BODY, ford 6r60 valve body check ball, a/c without ccc carb and computer g body, 6r60 upper valve body check ball installation, 6R60 valve body removal, 4L60E VALVE BODY BOLT LOCATIONS, 4hp22 transmission valve body diagram, 2006 4300 body controller, 09g body valve torque spec,

2001 Chevrolet Cavalier Idle Air Control Motor (IAC): Service and Repair REMOVAL PROCEDURE

0

Filed Under (Chevrolet) by admin on 16-09-2010

download
1. Remove the idle air control (IAC) valve connector. 2. Remove the IAC valve attaching screws (1). NOTE: If the IAC valve has been in service: DO NOT push or pull on the IAC valve pintle. The force required to move the pintle may damage the threads on the worm drive. Also, DO NOT soak the IAC valve in any liquid cleaner or solvent, as damage may result. 3. Remove the IAC valve assembly (2). ^ Clean the IAC valve O-ring sealing surface, the pintle valve seat, and the air passage. ^ The IAC valve may be cleaned. Use a shop towel or parts cleaning brush to remove any heavy deposits. ^ Any shiny spots on the pintle or seat are normal and do not indicate misalignment or a bent pintle shaft. ^ If the air passage have heavy deposits, remove the throttle body for a complete cleaning. ^ Inspect the IAC valve O-ring for cuts, cracks, or distortion. Replace the O-rings if necessary. ^ When installing a new IAC valve, be sure to replace the valve with an identical part. The IAC valve pintle shape and diameter are designed for a specific application. MEASUREMENT PROCEDURE This procedure is only for installing a new IAC valve. IMPORTANT: If installing a new IAC valve, replace the IAC valve with an identical part. The IAC valve pintle shape and diameter are designed for the specific application. Measure the distance between tip of the IAC valve pintle and the mounting flange. If the distance is more than 28 mm (1.1 in), use finger pressure to slowly retract the pintle. The force required to retract the pintle of a new valve will not cause damage to the valve. INSTALLATION PROCEDURE

Related entry:

mercruiser iac replacement, location iac valve 93 metro, Where is iac valve on suzuki verona, videos of Ford rangers with bad intake or exhaust valve, servotronic solenoid, rsx iac relearn, replacing 2001 cavalier purge solenoid valve, purge valve location for 2001 pt cruiser, 2001 toyota 2 4L throttle body components, lifter replacement 2003 chevy cavalier,

2001 Ford Escort Cylinder Head Disassembly

0

Filed Under (Ford) by admin on 24-10-2010

download
1. Remove the bolt and the camshaft position (CMP) sensor. 2. Remove the bolts, the rocker arm seats, and the rocker arms. 2. Remove the bolts, the rocker arm seats, and the rocker arms. 3. NOTE: Always return the valve tappets to their original tappet bores unless they are being replaced. Remove the valve tappet(s). 1. Remove the valve tappet guide plate retainers. 2. Remove the valve tappet guide plates. 3. Remove the valve tappets. Remove the bolts and the engine lifting eye. 5. Remove the (A) bolts and the (B) camshaft thrust plate. 6. Use Oil Seal Remover to remove the camshaft front seal. 7. NOTE: The camshaft can be removed in either direction. Remove the camshaft. 8. NOTE: Identify all parts with respect to the cylinder from which they were removed and whether the valve is an intake valve or an exhaust valve. Use (A) Valve Spring Compressor to compress the valve springs. While the valve spring is compressed, remove the (B) valve span” retainer key. 9. Slowly remove the valve spring compressor tool. 10. Remove the valves valve spring retainer and the valve spring. 11. Remove the valves. 12. Remove and discard the valve stem seals. Assembly