download
Manual locking hubs engage and disengage front wheels from axle shafts on 4WD vehicles. These hubs are are optional. When hubs are engaged in LOCK position, wheels and axle shafts rotate together. When hubs are disengaged or unlocked in FREE position, front wheels free-wheel on hub bearings. REMOVAL & INSTALLATION MANUAL LOCKING HUB Removal 1) Position locking hub in FREE position. Remove cover-to- body retaining bolts. Remove cover assembly and gasket. 2) Remove snap ring from drive axle. Remove body-to-hub retaining bolts. Remove body and gasket. See Fig. 1. CAUTION: Lubricate sliding surfaces with multipurpose grease, but DO NOT pack hub with grease.

download
Much has been written about swapping Suzuki’s G16B 1.6 liter 16-valve engine into the Samurai. It is mechanically very simple (as engine swaps go) but the wiring can be a daunting challenge for many. To date it has been necessary for the DIY builder to perform extensive research, gather all the information they can find, try to make sense of it, and take their best shot (or pay someone that has already done it). There is no one “correct” way to make this engine swap. The variations are nearly endless. Much of it involves personal preference. What is presented here is a process that is known to be successful, along with some of the more familiar options. ALL WIRING SHOULD BE DONE WITH THE BATTERY REMOVED FROM THE VEHICLE 1.1. It is HIGHLY RECCOMMENED that you purchase the appropriate Field Service Manual for your engine model year (either digital or print copy). Though there are only two sections that are relevant to a transplanted engine the information is absolutely invaluable. Much – but not all – of the required Information is also available in most aftermarket vehicle specific service manuals (Haynes, Chilton’s, etc.) The pertinent sections (6 & 8) of the 1996 Tracker FSM may be downloaded for free from Acksfaq.com (donations are appreciated). 1.2. 1992 through 1998 Suzuki/Geo (GM) vehicles with G16B (1.6 liter 16-valve) engines can be identified by the 8th digit in the Vehicle Identification Number. “0” for Suzuki badged vehicles, “6” for Geo’s (“U” indicates an 8-valve 1.6L). 1.3. The most common set-up, and arguably the simplest, mates a donor Tracker or Sidekick engine, with the Samurai 5- spd Manual Transmission. Donor engines with Automatic Transmissions (3 or 4 A/T) are easily rewired to work with the Samurai 5-spd M/T. Specific notations for installing the donor engine with a 3 A/T appear where necessary. The 4 A/T is significantly more complicated and is not included in these instructions. 1.4. It is preferred (but not required) that the ECM and engine be of the same model year. However, as long as the computer has all the necessary inputs and outputs it makes no difference what motor it is physically controlling. It should be noted that OBD1 vehicles (1995 & earlier) are much less complex than OBD2 vehicles (1996 & after). The earlier technology is far easier for the amateur auto electrician to manage. OBD2, being more modern, has nearly twice as many sensors & controls. Properly tuned, OBD2 engines will provide slightly more power, better fuel economy, and cleaner emissions. Replacement parts are also easier to find, but of course, are more expensive.

repair manual covers all US and Canadian models of Chevrolet Sprint and Metro, Geo Metro and Suzuki Swift, 1985 to 2000.
What’s Inside?
Introduction: Vehicle identification numbers; Buying parts; Maintenance techniques, and more. Tune-up and routine maintenance; Engine and overhaul procedures; Cooling, heating and air-conditioning systems; Fuel and exhaust systems; Engine electrical systems; Emissions control systems; Transmission; Brakes; Suspension and steering systems; Body; Chassis electrical system; Wiring diagrams

download
CONDITION: In extreme cold climates, the MIL may be ON when the engine is started. The DTC P2025 will be stored in the ECM.
CAUSE: ECM Software Logic CORRECTION: Using the appropriate service manual, verify the DTC using the troubleshooting chart.
If no cause for the DTC is found, reprogram the ECM by using the instructions listed below. Then clear
the DTC from the ECM memory

Comprehensive, single source of service information and specifications available specifically for BMW 5 Series from 1997 to 2002. The aim throughout this manual has been simplicity, clarity and completeness, with practical explanations, step-by-step procedures and accurate specifications. Whether you are a professional or a do-it-yourself BMW owner, this manual will help you understand, care for and repair your E39 5 Series. Though the do-it-yourself BMW owner will find this manual indispensable as a source of detailed maintenance and repair information, the BMW owner who has no intention of working on his or her car will find that reading and owning this manual will make it possible to discuss repairs more intelligently with a professional technician.
Engines covered in this BMW repair manual:
* 6-cylinder engines: M52, M52 TU, M54
* V-8 engines: M62, M62 TU
Fuel injection systems covered in this BMW repair manual:
* Bosch M 5.2, M 5.2.1, ME 7.2
* Siemens MS 41.0, MS 42.0, MS 43.0
Manual transmissions covered in this BMW repair manual:
* Getrag S5D 250G, S6S 420G
* ZF S5D 320Z
Automatic transmissions covered in this BMW repair manual:
* A4S 270R, A4S 310R
* A5S 360R, A5S 390R
* A5S 325Z
*A5S 560Z, A5S 440Z