map sensor tds outputs


You are searching repair manual in PDF format about map sensor tds outputs use another keyword for search another post or files



  map sensor tds outputs Direct Download speed 5787 Kb/s

  map sensor tds outputs Full Version speed 6767 Kb/s




1995 Ford Mustang Camshaft Position (CMP) Sensor Removal Installation

0

Filed Under (Ford) by admin on 08-02-2011

download
1. Disconnect battery ground cable (14301) . 2. Disconnect fuel charging wiring (9D930) from distributor stator (12A112) (camshaft position sensor). 3. Remove stator camshaft position sensor retaining screws and distributor stator (camshaft position sensor) from camshaft position sensor housing. 4. If removing camshaft position sensor housing from the engine front cover (6019) , proceed with Removal Step 5. If camshaft position sensor housing is not being removed, proceed to Installation Step 6. 5. CAUTION: Before proceeding with this procedure, set cylinder No. 1 to 26 degrees After Top Dead Center (ATDC) of the compression stroke. Then note the position of the stator (camshaft position sensor) electrical connector. The installation procedure requires that the connector be located in the same position. Remove retaining bolt and hold-down clamp (12270) . 6. NOTE: The oil pump intermediate shaft (6A618) should be removed with the camshaft position sensor housing. Remove camshaft position sensor housing from engine front cover . Installation 1. CAUTION: If the replacement distributor stator (camshaft position sensor) does not contain a plastic locator cover tool, a special service tool such as Syncro Positioning Tool T89P-12200-A must be obtained prior to installation of the replacement distributor stator (camshaft position sensor). Failure to follow this procedure will result in improper stator (camshaft position sensor) alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage. If the plastic locator cover tool is not attached to the replacement distributor stator (camshaft position sensor), attach Syncro Positioning Tool T89P-12200-A as follows: a. Engage camshaft position sensor housing vane into the radial slot of the tool. b. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing. The cover tool should be square and in contact with entire top surface of camshaft position sensor housing. 2. Transfer oil pump intermediate shaft from old camshaft position sensor housing to replacement camshaft position sensor housing. 3. CAUTION: If stator (camshaft position sensor) electrical connector is not positioned properly (for example, contacting the A/C compressor bracket), DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1. Install camshaft position sensor housing so that drive gear engagement occurs when arrow on locator tool is pointed approximately 30 degrees counterclockwise from the front face of the cylinder block (6010) . This step will locate stator (camshaft position sensor) electrical connector in the pre-removal position. 4. Install hold-down clamp and retaining bolt and tighten bolt to 20-30 Nm (15-22 lb-ft). 5. Remove Syncro Positioning Tool T89P-12200-A. 6. CAUTION: If stator (camshaft position sensor) electrical connector is not positioned properly (for example, contacting the A/C compressor bracket), DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1. Install distributor stator (camshaft position sensor) and retaining screws. Tighten screws to 2.5-3.5 Nm (22-31 lb-in). 7. Connect fuel charging wiring connector to distributor stator (camshaft position sensor). 8. Connect battery ground cable .

Related entry:

2004 aveo camshaft position sensor removal, 2006 ml350 left cam plug engine, chilton 2004 chevy astro install haf sensor, replcing ect sensor on hyundai santa fe, how to replace a crankshaft sensor pigtail for a 2001 isuzu 2 2, reset throttle body 2005 Cobalt, 2004 explorer tps install, lexus es 300 p0128, pt cruiser torque specs timing sprokets, 2002 nissan quest p1401 o2 sensor diagram,

1998 Ford Windstar Camshaft Position (CMP) Sensor REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 17-02-2011

download
CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126) , set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Then note the position of the camshaft position sensor electrical connector. The installation procedure requires the connector be located in the same position. Removal 1. Disconnect battery ground cable (14301). Refer to Section 14-01. 2. Disconnect fuel charging wiring connector from camshaft position sensor. 3. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing. 4. If removing camshaft position sensor housing from the cylinder block (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to Step 6 of the installation procedures. 5. Remove hold-down clamp (12270) (bolt and washer assembly). 6. NOTE: Remove the oil pump intermediate shaft (6A618) with the camshaft position sensor housing. Remove camshaft position sensor housing from cylinder block. Installation 1. CAUTION: If the replacement camshaft position sensor housing does not contain a plastic locator cover tool, a special service tool must be obtained prior to installation of the replacement camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the ignition fuel system being out of time with the engine, possibly causing engine damage. NOTE: For 3.0L engines, use Syncro Positioning Tool 303-589. For 3.8L engines, use Syncro Positioning Tool 303-562 (T96T-12200-A). If the plastic locator cover tool is not attached to the replacement camshaft position sensor housing, attach syncro positioning tool as follows: a. Engage camshaft position sensor housing vane into the radial slot of the tool. b. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing. 2. Transfer oil pump intermediate shaft from old camshaft position sensor housing to replacement camshaft position sensor housing. 3. Install camshaft position sensor housing so drive gear engagement occurs when arrow on syncro positioning tool is pointed approximately as shown in the illustrations. This step will locate camshaft position sensor electrical connector in the pre-removal position. 4. Install hold-down clamp (washer and bolt assembly) and tighten bolt to 20-30 Nm (15-22 lb-ft). 5. Remove syncro positioning tool. 6. CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1. Install camshaft position sensor and retaining screws. On 3.0L engine, tighten screws to 2.5-3.5 Nm (23-30 lb-in). On 3.8L engine, tighten screws to 4.5-7 Nm (40-61 lb-in). 7. Connect fuel charging wiring connector to camshaft position sensor. 8. Connect battery ground cable. Refer to Section 14-01. Camshaft Position Sensor—3.0L Engine

Related entry:

1998 saturn sl2 transmission range switch adjustment,

2003-2006 Chevrolet Express Antilock Brake (ABS) Activation At Low Speeds (Clean Wheel Speed Sensor Mounting Surface)

0

Filed Under (Chevrolet) by admin on 25-01-2011

download
Condition Some customers may comment on ABS activation at low speeds, usually below 8 km/h (5 mph). Upon investigation, the technician will find no DTCs set. Cause The cause of this condition may be an increased air gap between the wheel speed sensor and the hub reluctor ring due to rust and debris built up on the sensor mounting surface. Correction Measure AC voltage and clean the wheel speed sensor mounting surfaces. 1. 2. 3. 4. Raise and support the vehicle. Disconnect both the front wheel speed sensor connectors at the frame and harness. Place a Digital Volt Meter (DVM) across the terminals of each wheel speed sensor connector. Rotate the wheel clockwise approximately one revolution per second. The minimum reading should be at least 350 ACmV’s. If the reading is less than 350 ACmV’s, remove the wheel speed sensor. 5. Plug the wheel speed sensor bore in order to prevent debris from falling into the hub during service. 6. Clean the wheel speed sensor mounting surface using a wire brush, sand paper, emery cloth, scotch brite, or other suitable material. Be sure to thoroughly clean the wheel speed sensor surface. There should be no rust or corrosion. 7. Check the sensor head to determine if it has been warped/distorted due to the corrosion build up or other causes. Check the mounting surface on the sensor head for flatness by placing it on the edge of a metal machinists scale or other suitable straight edge to measure the flatness. Check the sensor for flatness in multiple (minimum 3) positions/directions. If the sensor head is distorted, replace the sensor. 8. Apply (spray) two thin coats of the specified rust penetrating lubricant (corrosion inhibitor) to the complete sensor mounting surface on the bearing hub. Allow to dry for 3-5 minutes between coats. Use ONLY Rust Penetrating Lubricant, P/N 89022217 (in Canada, P/N 89022218). 9. When the corrosion inhibitor is dry to the touch (about 10 minutes), apply a thin layer of bearing grease to the hub surface and sensor O-ring prior to sensor installation. Use ONLY Wheel Bearing Lubricant, P/N 01051344 (in Canada, P/N 993037). 10.Install either the original sensor or a new one in the hub. Ensure that the sensor is seated flush against the hub. Refer to the applicable Wheel Speed Sensor Replacement procedure in the ABS sub-section of the Service Manual. 11.Place the DVM across the sensor terminals and recheck the voltage while rotating the wheel. The voltage should now read at least 350 ACmV’s.

Related entry:

how replace 2011 kia sorento right wheel speed sensor, diagram of 2000 buick lesabre rear wheel speed sensor, where is the sensor for 2005 Buick LeSabre located on the transmission, 2004 kia spectra speed sensor location, 2002 bmw 525i speed turbine sensor, how to replace abs sensor in 2002 sonoma, how to replace chevy blazer 2001 transmission control sensor, how to replace rear wheel sensor on buick lacrosse, input speed sendor diagram for a 02 tracker, isuzi d max 2007 front right wheel speed sensor,

2002 Jeep Wrangler CMP and CKP Removal and Installation

0

Filed Under (Jeep) by admin on 01-12-2010

download
The Camshaft Position Sensor (CMP) on the 4.0L 6cylinder engine is bolted to the top of the oil pump drive shaft assembly. The sensor and drive shaft assembly is located on the right side of the engine near the oil filter. The rotational position of oil pump drive determines fuel synchronization only. It does not determine ignition timing. WARNING Do NOT attempt to rotate the oil pump drive to modify ignition timing. 1. Two different procedures are used for Removal & Installation. The first procedure will detail Removal & Installation of the sensor only. The second procedure will detail Removal & Installation of the sensor and oil pump drive shaft assembly. The second procedure is to be used if the engine has been disassembled. 2. An internal oil seal is used in the drive shaft housing that prevents engine oil at the bottom of the sensor. The seal is not serviceable. Sensor Only 1. Disconnect electrical connector at CMP sensor. 2. Remove 2 sensor mounting bolts. 3. Remove sensor from oil pump drive. Oil Pump Drive & Sensor WARNING If the CMP and oil pump drive are to be removed and installed, do NOT allow engine crankshaft or camshaft to rotate. CMP sensor relationship will be lost. Disconnect electrical connector at CMP sensor. Remove 2 sensor mounting bolts Remove sensor from oil pump drive. Before proceeding to next step, mark and note rotational position of oil pump drive in relationship to engine block. After installation:, the CMP sensor should face rear of engine 0. 5. Remove hold-down bolt and clamp. 6. While pulling assembly from engine, note direction and position of pulse ring. After Removal & Installation, look down into top of oil pump and note direction and position of slot at top of oil pump gear. 7. Remove and discard old oil pump drive-to-engine block gasket. 1. 2. 3. 4. Sensor Only The Camshaft Position Sensor (CMP) on the 4.0L 6cylinder engine is bolted to the top of the oil pump drive shaft assembly. The sensor and drive shaft assembly is located on the right side of the engine near the oil filter. 1. Install sensor to oil pump drive. 2. Install 2 sensor mounting bolts and tighten to 2 Nm (15 inch lbs.) torque. 3. Connect electrical connector to CMP sensor. Oil Pump Drive & Sensor 1. Clean oil pump drive mounting hole area of engine block. 2. Install new oil pump drive-to-engine block gasket.

Related entry:

@cmpoil com, @cmpoil com loc:US, 2011 toyota tucoma drive shaft removal, ford fiesta drive shaft overhaul repair, 2003 honda crv drive shaft schematic, Ford 4 0 Sohc Oil Pump Drive Gear, FORD 4 0 SOHC OIL PAN CARRIER REMOVEAL, drive shaft repair transit connect, como checar el ckp de un jeep wrangler 2 5, b2500 drivershaft seal,

1999 Ford Taurus Camshaft Position (CMP) Sensor SHO Removal Installation

0

Filed Under (Ford) by admin on 11-02-2011

download
Camshaft Position (CMP) Sensor SHO Removal 1. Disconnect battery ground cable (14301) . Refer to Section 14-01. 2. Remove the engine appearance cover. For additional information, refer to Section 03-01C. 3. Disconnect engine control sensor wiring (12A581) from camshaft position sensor (CMP sensor) (6B288) . 4. Remove camshaft position sensor retaining bolt and remove camshaft position sensor from engine. Installation 1. Make sure camshaft position mounting sensor surface is clean and that camshaft position sensor O-ring is in proper location on camshaft position sensor . 2. CAUTION: Do not overtighten camshaft position sensor retaining bolt or damage to camshaft position sensor or engine mounting surface may occur. Position camshaft position sensor onto engine and install retaining bolt. Tighten retaining bolt to 8-12 Nm (71-106 lb-in). 3. Connect engine control sensor wiring to camshaft position sensor . 4. Install the engine appearance cover. For additional information, refer to Section 03-01C. 5. Connect battery ground cable . Camshaft Position Sensor