Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
FUSES & CIRCUIT BREAKERS
Fig. 4: Identifying Instrument Panel Fuse Box MAZDA MOTORS CORP.
2003 Mazda Tribute DX

download
1. Disconnect the battery. See BATTERY DISCONNECT . 2. Remove the screws (1) and pull the center finish trim panel finish panel (2) out from the instrument panel. Fig. 3: Removing Center Finish Trim Panel Finish Panel Courtesy of MAZDA MOTORS CORP.
3. Disconnect the electrical connectors and remove the radio and center instrument panel finish panel. 4. Remove the screws (1) and remove the inner hood lock release handle (2) Fig. 4: Removing Inner Hood Lock Release Handle Removing Instrument Panel Steering Column Cover Removing Instrument Panel Steering Column Opening Cover Reinforcement Removing Instrument Cluster Finish Panel Fig. 8: Disconnecting Connectors Fig. 10: Removing Transmission Range Indicator

download
Removal 1. If equipped with power seats, move the seat fully rearward. 2. If equipped with adjustable pedal system, move the pedal to the full forward position. 3. If equipped with a manual transmission, place the transmission in second gear. 4. Remove the passenger air bag module. For additional information, refer to Section 501-20B. 5. Close the glove compartment. 6. Position the battery junction box (BJB) aside. Release the mounting tabs. 7. Remove the bulkhead electrical connectors from inside the engine compartment. 1. Loosen the bolts. 2. Disconnect the bulkhead electrical connectors. 8. Remove the bulkhead electrical connector insulator. 9. Unclip the bulkhead electrical connectors from the dash panel. 10. Remove the instrument panel steering column cover. For additional information, refer to Instrument Panel — Steering Column Cover in this section. 11. If equipped, remove the valance panel. Remove the two pin-type retainers and release the expander clip. 12. Disconnect the restraint control module (RCM) electrical connector. 1. Release the locking tab. 2. Disconnect the RCM electrical connector. Release the wiring harness locators. 13. Disconnect the electronic blend door actuator electrical connector. Release the wiring harness locators. 14. Disconnect the climate control head vacuum harness connector. 15. Remove the LH and RH front door scuff plates. 16. Position the LH and RH door weatherstrip seals aside. 17. Remove the LH and RH A-pillar lower trim panels. 18. If equipped, remove the alternative fuel control module (AFCM). 1. Disconnect the electrical connector. 2. NOTE: The AFCM is attached with Velcro®. Remove the AFCM from the vehicle by pulling gently down and to the right. 19. Remove the LH and RH A-pillar passenger assist handles. 1. Remove the four screw covers and four screws. 2. Remove the LH and RH A-pillar passenger assist handles. 20. Remove the LH and RH windshield side garnish mouldings. 21. Disconnect the brake pedal position (BPP) switch electrical connector. Release the wiring harness locators.

download
1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Disconnect the negative battery cable. Remove the floor console. Remove the sun sensor and the automatic temperature controls assembly. Remove the tweeter speakers and the stereo cassette AM/FM radio. Refer to Section 9F, Audio Systems. Remove the screws and the instrument panel storage compartment. Remove the instrument cluster dimmer switch assembly. Remove the instrument cluster. Remove the chime module. Remove the kick panels. Remove the glove box. Remove the screws and the glove box housing. Disconnect the glove box housing electrical connectors. Remove the knee bolster. 14. Remove the nuts and the bolts securing the steering column. 15. Disconnect the steering column electrical connectors. 16. Lower the steering column. 17. Remove the screw behind the stereo cassette AM/FM radio. 18. Remove the screw securing the instrument panel to the heater air distributor case. 19. Remove the bolts and the glove box brace. 20. Remove the instrument panel screw behind the glove box brace. 21. Remove the instrument panel bolts below the windshield. 22. Remove the bolts securing the bottom of the instrument panel to the floor. 23. Remove the bolts securing the sides of the instrument panel to the body.

download
Instrument Panel Removal CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. 1. Depower the supplemental restraint system (SRS). For additional information, refer to Supplemental Restraint System (SRS) Depowering and Repowering in Section 501-20B. 2. Remove the LH front wheel and tire assembly. For additional information, refer to Section 204-04. 3. Position the LH fender splash shield away from the dash panel. 1. Remove the pin-type retainers. 2. Remove the screws. 3. Position the LH fender splash shield away from the dash panel. 4. Disconnect the bulkhead electrical connector from inside the fender opening. 1. Loosen the bolt. 2. Disconnect the bulkhead electrical connector. 5. Release the bulkhead electrical connector from the dash panel. 6. Install the LH front wheel and tire assembly. For additional information, refer to Section 204-04. 7. Remove the floor console. For additional information, refer to Floor Console in this section. 8. Remove the upper RH instrument panel support bolt. 9. Disconnect the antenna in-line connector. 10. Disconnect the climate control vacuum harness connector. 11. Close the glove compartment. 12. Remove the LH and RH scuff plates. 13. Remove the LH and RH A-pillar lower trim panels. 1. Remove the pin-type retainers. 2. Remove the A-pillar lower trim panels. 14. Remove the LH and RH windshield side garnish mouldings. If equipped with a convertible top, remove the pin-type retainers. 15. Position the LH and RH door weatherstrips aside. 16. Disconnect the RH main wiring harness electrical connectors. 17. Disconnect the climate control wiring harness connector. 18. Remove the instrument panel steering column cover. 1. Remove the screws. 2. Remove the instrument panel steering column cover. 19. Remove the instrument panel reinforcement. 1. Remove the screws. 2. Remove the instrument panel reinforcement. 20. Separate the intermediate shaft from the steering column shaft. 1. Remove the pinch bolt. 2. Separate the intermediate shaft from the steering column shaft. 21. NOTE: The corner of the carpet may have to be pulled back slightly to carry out this step. Disconnect the LH main wiring harness electrical connectors.