mazda b2500 diesel


You are searching repair manual in PDF format about mazda b2500 diesel use another keyword for search another post or files



  mazda b2500 diesel Direct Download speed 5787 Kb/s

  mazda b2500 diesel Full Version speed 6767 Kb/s




Mazda MX-5 Mazda MIATA Electric Cooling Fans – Service

0

Filed Under (Mazda) by admin on 21-06-2010

download
Cooling fan motors operate when Powertrain Control Module (PCM) determines fan operation depending on crankshaft position, Engine Coolant Temperature (ECT) sensor, vehicle speed, Intake Air Temperature (IAT) sensor, A/C switch and refrigerant pressure switch inputs. Cooling fans receive power through the cooling fan relay. Condenser fan operates only when A/C compressor clutch engages except 2004 models with turbocharger which uses dual fans for engine cooling with or without A/C operation. See WIRING DIAGRAMS . COMPONENT LOCATION For component locations, refer to illustrations. See Fig. 1 -Fig. 3 .

1993 Mazda 626 Speedometer – Replacement Procedure

0

Filed Under (Mazda) by admin on 12-11-2010

download
NOTE: 1. Mazda vehicles are manufactured with tamper-proof speedometers and the mileage can not be altered or adjusted. 2. When a speedometer is replaced, the new speedometer will read zero (0). 3. This procedure is extremely important to accurately represent actual vehicle mileage. 4. The “Speedometer Replacement Label” referenced below is available through the Mazda Program Center for a limited time. Mazda Motor of America, Inc. is providing 1 sheet of 20 labels with this bulletin (see Illustration). REPLACEMENT PROCEDURE 1. Remove and replace the speedometer according to the workshop manual. 2. Complete the following information on the “Speedometer Replacement Label.” ^ Mileage before speedometer replacement ^ Date of replacement ^ Dealer code. 3. Attach the label to the driver’s side “B” pillar. 4. Complete the “Speedometer Replacement Record” in the Warranty Information Booklet as referenced.

2009 Ford F-250 Thermostat 6.4L Diesel Engine Removal

0

Filed Under (Ford) by admin on 07-05-2011

download
Removal NOTE: Removal of the vertical EGR cooler is not required to service the thermostats. 1. Remove the upper cooling fan shroud. For additional information, refer to Cooling Fan Shroud — 6.4L Diesel, Upper in this section. 2. Remove the degas bottle. For additional information, refer to Degas Bottle — 6.4L Diesel in this section. 3. Using a mirror, find the end of the upper radiator hose spring clip. Remove the spring clip, disconnect the upper radiator hose from the thermostat housing and position the upper radiator hose aside. 4. Remove and discard the nut and the vertical EGR cooler lower clamp. 5. Remove the bolt and the vertical EGR cooler lower bracket. 6. NOTE: Vertical EGR cooler removed from art for clarity. Disconnect the wiring from the heater return tube. 7. Remove the 2 bolts and position out the LH heater return tube. • Remove and discard the O-ring seal. 8. NOTE: The 6.4L diesel engine uses 2 thermostats. Remove the 4 bolts, the collar and the thermostat housing. • Lift the bottom of the collar up and rotate toward the engine to remove. 9. NOTICE: If the thermostats are contaminated with engine oil, new thermostats must be installed. Reusing a thermostat that has been exposed to engine oil may result in engine overheating. Remove the thermostats and the gasket from the thermostat housing. • Discard the gasket. Installation 1. Install a new gasket and the thermostats into the thermostat housing. 2. Install the thermostat housing, the collar and the 4 bolts. • Tighten to 13 Nm (115 lb-in). 3. NOTE: Vertical EGR cooler removed from art for clarity. NOTE: Install a new O-ring seal. Install the LH heater return tube and the 2 bolts. • Tighten to 13 Nm (115 lb-in). 4. Connect the wiring to the heater return tube. 5. Position the lower vertical EGR cooler bracket and loosely install the bolt. 6. Install a new vertical EGR cooler lower clamp. Tighten the clamp nut in 3 stages. • Stage 1: Tighten the nut to 10 Nm (89 lb-in). • Stage 2: Loosen the nut 720 degrees (2 complete turns). • Stage 3: Tighten the nut to 8 Nm (71 lb-in). 7. Tighten the lower EGR cooler bracket bolt. • Tighten to 62 Nm (46 lb-ft). 8. Connect the upper radiator hose to the thermostat housing. Install the spring clip. • Verify the spring clip is correctly seated. 9. Install the degas bottle. For additional information, refer to Degas Bottle — 6.4L Diesel in this section. 10. Install the upper cooling fan shroud. For additional information, refer to Cooling Fan Shroud — 6.4L Diesel, Upper in this section.

89-94 MAZDA B2200,2600 MPV ECM ECU COMPUTER REPAIR

0

Filed Under (Mazda) by admin on 19-09-2009

MAZDA B2200, 2600, MPV showing or doing any of the problems listed below then this repair service will take care of your problem. * The Truck works intermittently * Is completely dead * Is running only on 2 Cylinders * The truck runs rough * The truck runs for a few minutes and then dies * No 5 volt reference. * May start when it is cold outside, and die when it gets warmed up.* *If you are not sure if this service is for you just email me at digitalguy_1@charter.net
THIS WILL FIT THE TRUCKS LISTED BELOW * 1989 to 1994 MAZDA 2200 * 1989 to 1994 MAZDA 2600 * 1990 to 1994 MAZDA MPV

Ford Escort, Fiesta, Sierra, Mondeo, P100, 1.8 Diesel/Turbo diesel Camshaft Belt / Fuel Injection Pump Belt Common Causes of Failure

0

Filed Under (Ford) by admin on 05-06-2011

download
Common causes of camshaft timing belt failure on the above vehicles are due to incorrect operating tension, or ingress of dirt, water, or debris entering the timing belt cover. Predominantly on Fiesta models a high percentage of camshaft timing belt failures occur after the ancillary poly ‘V’ drive belt has failed, where strands of material off the broken belt have entered the timing belt cover. This is especially so where an ancillary belt has been fitted that does not contain “Kevlar” based materials. It is therefore important to always remove the timing belt cover to check for belt debris if the ancillary belt has failed. Any contamination that enters the timing belt cover can become compressed between the surfaces of the camshaft timing belt and drive pulleys. This causes wear to both the belt teeth, backing surface, and damage to the drive pulleys, resulting in premature failure of the camshaft timing belt. Later engines have modifications to improve the sealing of the belt cover around the crankshaft pulley, to reduce the level of outside contamination. Incorrect tensioning of the belt during installation will adversely affect the life of the belt. Before fitting a new belt it is important to check and observe the following points :- 1) Right Hand Inner Wing Splash Shield (Fiesta, Escort, Mondeo) This must be fitted and undamaged. 2) Timing Belt Cover Check that all components of the cover are fitted and undamaged. Ensure the latest type of modified cover is fitted. 3) a) Toothed Drive Pulleys Check that the tooth profiles are not worn or damaged. On vehicles built before January 1994 special attention should be given to the nylon toothed pulley situated below the camshaft pulley in a clockwise position on the belt drive (see diag item 4). This should be changed to a modified steel pulley (Ford No. 7053802) plus bolt (6701537). Ensure that the Camshaft and Injection Pump sprockets are free to rotate on the drive locations when the retaining bolts are slackened off. b) 4) a) b) c) Water Pump, Idler and Tensioner Pulleys Check that the belt running surfaces are not worn or damaged. Check that the flanges are running true and not damaged. Check that the water pump, and pulley bearings are in good condition, to ensure correct belt alignment. 5) Crankshaft Pulley The toothed pulley is in two parts. The rear section (Injection Pump Drive) is located onto the crankshaft by a small drive pin. The front section (Camshaft and “Poly V” belt drive) engages onto the rear pulley via a small vee protrusion on the rear face. Should the central fixing bolt for the crankshaft pulley come loose, or an old bolt re-used (Stretch bolt design), it is possible for fretting to take place damaging the locations. The crankshaft and camshaft pulleys can then move out of timing alignment, resulting in valve and piston contact damage. Replacement Procedure As the vehicle is fitted with two timing belts, one to drive the Camshaft, and one to drive the Injection Pump drives, which are driven off the crankshaft pulley, it is strongly recommended that both belts are replaced at the same time. NOTE: Special tools are required to lock the crankshaft, camshaft, and injection pump in the correct angular location when changing the belts, to ensure correct timing position. IMPORTANT: Ensure the engine is cold (not run for 4 hours) before commencing working as this will affect the setting of the timing belt tension and could lead to premature failure. Continued . . . .