mercedes C 180


You are searching repair manual in PDF format about mercedes C 180 use another keyword for search another post or files




2000 Mercedes-Benz ML320 Engine light is on with no acceleration. Fault code is P0120

0

Filed Under (Mercedes-Benz) by admin on 11-06-2010

download
2000 Mercedes-Benz ML320 3.2L 2001 Mercedes-Benz E320 3.2L 2001 Mercedes-Benz C240 2.6L 2001 Mercedes-Benz E320 4Matic 3.2L 2001 Mercedes-Benz C320 3.2L 2002 Mercedes-Benz ML320 3.2L Potential Causes: Pedal Sensor Throttle Body Wiring Tech Tips: With new sensor the throttle stops must be relearned. Use compatible scan tool and perform adaptations. ALWAYS verify charging system voltage is correct. Tests/Procedures: 1. Connect scan tool and monitor voltages of pedal sensor B37. Signal 1 (Accelerator pedal position: Idle speed):[0.2...0.5] V Signal 2 (Accelerator pedal position: Idle speed):[0.1...0.5] V Signal 1 (Accelerator pedal position:Kickdown):[4.3...4.8] V Signal 2 (Accelerator pedal position:Kickdown):[2.1...2.5] V 3. Test throttle body voltages with scan tool. Potentiometer #2 signal voltage ignition on, accelerator pedal position CTP 0.3-0.9 VDC, WOT > CTP value Potentiometer #1 signal voltage Ignition on, accelerator pedal position CTP 4.0-4.6 VDC, WOT < CTP value.

Mercedes-Benz C-Class (W202) Service Manual: 1994-2000 C220, C230, C230 Kompressor, C280

0

Filed Under (Mercedes-Benz) by admin on 13-09-2009

download

Manual contains in-depth maintenance, service and repair information for the Mercedes-Benz C-Class from 1994 to 2000. The aim throughout has been simplicity and clarity, with practical explanations, step-by-step procedures and accurate specifications. Whether you’re a professional or a do-it-yourself Mercedes-Benz owner, this manualhelps you understand, care for and repair your car Electrical system service, with an easy-to-use illustrated component
locator section. • Comprehensive wiring schematics, including power distribution and grounds. • Mercedes-Benz OBD II diagnostic trouble codes, SAE-defined OBD II P-codes, as well as basic scan tool operation.
• Mercedes-Benz factory tolerance, wear limits, adjustments and tightening torque

1996 Mercedes-Benz C220 TROUBLE SHOOTING TRANSMISSION SLIPS IN ALL GEARS

0

Filed Under (Mercedes-Benz) by admin on 19-06-2010

download
AUTOMATIC TRANSMISSIONS Mercedes-Benz 722 Series – Electronic Diagnosis C220, C280, C36, E300D, E320 E420, S320, S350D, S500, S600 SL320, SL500, SL600 Incorrect modulating pressure. Modulating pressure control valve or pressure relief valve is dirty or sticking. Vacuum line to transmission vacuum capsule clogged or leaking. Working pressure control valve dirty or sticking. Low working pressure. Defective primary pump. Transmission Slips When Starting Off In 1st Or 2nd (Reverse Is Okay) Band B-2 shift valve sticking. Band B-2 piston worn or damaged. Band B-2 adjusted incorrectly or worn or damaged. Adjust brake band B-2 by installing a longer thrust pin (if necessary). If transmission operates properly with selector lever in “2″, but not in “3″ or “D” position, one-way clutch may be slipping

1985 Mercedes Benz 380SE Lambda System Function Test

0

Filed Under (Mercedes-Benz) by admin on 09-08-2010

download
Lambda closed loop tester with yellow test wire – 909 589 00 21 00 Oil telethermometer – 116 589 272 100 Test Conditions: Ignition system must be in good working order and engine at idle speed. Ignition timing must be set to specification. Testing Test Procedure Tests and General Diagnostics Lambda System Function Test 1985 Mercedes Benz 380SE (126 Chassis) V8-3839cc 3.8L SOHC (116)

2002 Mercedes Benz ML 320 Maintenance: Service Intervals Service Schedule

0

Filed Under (Mercedes-Benz) by admin on 27-06-2010

download
B – Service Schedule Brake Test – Brake test on dynamometer or test drive. Check parking brake and run in according to specifications (observe instructions in Maintenance Manual on vehicles with 4ETS, ESP!). Vehicle Passenger Compartment Function Check: – Check Tele Aid by pressing SOS button to make test call to Response Center. – Horn, headlamp flasher, hazard flasher, turn signals. – Warning/indicator lamps, illumination and interior lighting. – Throttle cable: operate accelerator cable slowly by foot through full range of travel. Observe smoothness of operation. If roughness is detected, replace throttle cable. – Exterior lighting incl. headlamps. – Windshield wipers, rear window wiper, windshield/rear window washer. – Headlamp cleaning system. – Check seat belts for damage and proper function. – Reset Flexible Service System (FSS) counter in instrument cluster. – Replace dust filter. Wheels, Brakes – Remove and reinstall wheels, rotate if necessary, does not apply for vehicles with different tire sizes front/rear. – Check brake pads for lining thickness front/rear. – Check condition of brake discs front and rear. – Check tires for damage and condition. – Measure and record tread depth. – Correct tire inflation pressure.