mitsubishi L200, 4D56, 2003, 4*4
You are searching repair manual in PDF format about mitsubishi L200, 4D56, 2003, 4*4 use another keyword for search another post or files
mitsubishi L200, 4D56, 2003, 4*4 Direct Download speed 5787 Kb/s
mitsubishi L200, 4D56, 2003, 4*4 Full Version speed 6767 Kb/s
Filed Under (Mitsubishi) by admin on 18-12-2010
Function The original intercooler for the L200 is quite small. Because of this the cooling capacity is low and the pressure drop is considerable. When increasing the power output of the L200 engine the boost air temperature must be kept as low as possible, while it has a great influence in performance as well as engine durability. Charge air cooling also has a positive effect on exhaust emissions from diesel engines. The pressure drop through the charge air cooler lowers the air mass flow trough the engine. To maximize air mass flow is essential to increase performance. The sttemtec charge air cooler upgrade maximizes the cooling capacity and minimizes the pressure drop of the charge air cooler without any negative effects of the vehicle. List of content 1. Charge air cooler 2. Air hose 3. Bag, Brackets and rubber mountings for intercooler Installation Installation preparations 1. Perform test drive with verification of general engine functions. 2. Wash engine bay with special attention to radiator and intercooler (wash, compressed air). System installation Remove the radiator grille by first remove the four plastic clips and then the claws by pulling out and up.
Filed Under (Ford) by admin on 11-05-2010
Some 1999-2004 Navigator, 2002-2003 Blackwood, 2003-2005 Aviator, 2003-2004 Marauder and 2003-2004 Mustang vehicles built before 12/19/2004 equipped with 4.6L 4V/5.4 4V engine may exhibit a runs rough, lacks power, and engine misfire, prompted by a MIL light and DTC codes P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, and P0316. ACTION Diagnose engine for engine misfire concern. If diagnostics determine an engine misfire which is characterized by leakage through exhaust valve(s), only replace the affected cylinder head(s). SERVICE PROCEDURE
Filed Under (Mitsubishi) by admin on 07-06-2010
Valve timing procedures Valve timing procedures Ensure crankshaft at TDC on No.1 cylinder. Ensure crankshaft pulley timing mark aligned with 0° timing mark on chain cover . Ensure notch on camshaft points upwards . If notch not visible, turn crankshaft one more turn. Install timing gears as follows: Ensure crankshaft gear and intermediate shaft gear timing marks aligned . Install LH balancer shaft . Ensure timing marks on intermediate shaft gears and LH balancer shaft gear aligned  & . Ensure RH balancer shaft gear and oil pump gear timing marks aligned . Install oil pump housing complete with RH balancer shaft. Ensure timing marks on oil pump gear and crankshaft gear aligned . Install injection pump as follows  : Ensure notch on injection pump gear aligned with mark ‘T’ on flange . During installation of injection pump: Notch on gear moves in direction of arrow. Install timing chain as follows:
Filed Under (Mitsubishi) by admin on 05-01-2011
This manual is designed for use with the 2003 LANCER EVOLUTION VIII Service Manual Volume 2, and Volume 3, and the 2003 LANCER EVOLUTION VIII Body Repair Manual to provide complete service information for the 2003 LANCER EVOLUTION VIII. Service or maintenance of any SRS component or SRS-related component must be performed only at an authorized MITSUBISHI dealer. MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B, Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of the SRS or any SRS-related component. • •
Filed Under (GM) by admin on 20-05-2010
2001-2002 Chevrolet Camaro 2001-2003 Chevrolet Corvette 2001-2002 Pontiac Firebird 2002-2003 Cadillac Escalade, Escalade EXT
2000-2003 Chevrolet Suburban, Tahoe 2001-2003 Chevrolet Silverado 2002-2003 Chevrolet Avalanche 2000-2003 GMC Yukon, Yukon XL 2001-2003 GMC Sierra with 4.8L, 5.3L, 5.7L or 6.0L V8 Engine (VINs V, T, Z, G, S, N, U – RPOs LR4, LM7, L59, LS1, LS6, LQ9, LQ4)
Condition Some customers may comment on an engine tick noise. The distinguishing characteristic of this condition is that it likely will have been present since new, and is typically noticed within the first 161-322 km (100-200 mi). The noise may often be diagnosed as a collapsed lifter. Additionally, the noise may be present at cold start and appear to diminish and then return as the engine warms to operating temperature. This noise is different from other noises that may begin to occur at 3219-4828 km (2000-3000 mi).