mitsubishi lancer 1994 wiring diagram


You are searching repair manual in PDF format about mitsubishi lancer 1994 wiring diagram use another keyword for search another post or files



  mitsubishi lancer 1994 wiring diagram Direct Download speed 5787 Kb/s

  mitsubishi lancer 1994 wiring diagram Full Version speed 6767 Kb/s




2003 MITSUBISHI LANCER EVOLUTION VIII SERVICE MANUAL

0

Filed Under (Mitsubishi) by admin on 05-01-2011

download
This manual is designed for use with the 2003 LANCER EVOLUTION VIII Service Manual Volume 2, and Volume 3, and the 2003 LANCER EVOLUTION VIII Body Repair Manual to provide complete service information for the 2003 LANCER EVOLUTION VIII. Service or maintenance of any SRS component or SRS-related component must be performed only at an authorized MITSUBISHI dealer. MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B, Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of the SRS or any SRS-related component. • •

Mitsubishi Lancer Short Throw Shifter Installation Manual

0

Filed Under (Mitsubishi) by admin on 24-12-2010

download
Mitsubishi Lancer Evolution IV, V, VI, VII, VIII Mitsubishi Lancer FWD 2001 and up Mitsubishi Eclipse 2000 and up Estimated Installation Time: 30-45 Minutes Tools Required: -Philips head screwdriver -8mm wrench -10mm wrench -12mm wrench -8mm, 10mm, and 12mm sockets and ratchet -Bench vise -Grinder 1. Carefully unscrew the stock shift knob. 2. Remove ashtray and screw beneath it. 3. Remove two screws from inside the center console storage compartment. 4. Lift up on the rear section of the center console and unclip it from the front section. 5. Remove plastic screw from the driver’s side of the center console (near the gas pedal). Remove the plastic cover and the pop rivet beneath it. Then remove the two screws at the rear of the console (were hidden by the rearward part of the center console that was removed). 6. Unclip plastic connector at the rear of the console. Remove entire center console. 7. Loosen and remove the bolts at the front and rear of the plastic assembly. Note the order these parts are in as they must be replaced in the same order later in the installation. The front bolt does not need to be completely removed from the plastic assembly, only pulled out enough to allow the top part of the plastic assembly to be lifted off. Now remove the top of the assembly exposing the top of the shifter main pivot ball. 8. Remove the clip on the bottom of the shifter, which connects it to the lower shifter cable. Remove the plastic pivot cup from the lower shifter cable. Also remove the clip attaching the left side shifter cable to the shifter arm. The stock shifter can now be removed. 9. For an Evolution 8 follow this step: using a grinder, shave down the sides of the counterweight / boot support in order to remove the white plastic cup. This in no way damages the stock shifter and it is still usable after the procedure. This enables you to remove the white plastic retaining ring without any cutting.

TOYOTA RAV4 ELECTRICAL WIRING DIAGRAM

0

Filed Under (Toyota) by admin on 28-09-2009

ELECTRICAL WIRING DIAGRAM
This Service Bulletin is to inform you of the Electrical Wiring Diagram for RAV4 equipped with 1CD-
FTV engine.RELAY LOCATIONS ELECTRICAL WIRING ROUTING OVERALL ELECTRICAL WIRING DIAGRAM CONNECTOR JOINING WIRE HARNESS AND WIRE HARNESS

download

Exhaust System Installation For 2008 & 2010 Mitsubishi Lancer Evolution 2009 Mitsubishi Ralliart

0

Filed Under (Mitsubishi) by admin on 20-12-2010

download
Exhaust System Removal Note: With a used vehicle, we suggest a penetrating spray lubricant to be applied liberally to all exhaust fasteners and al- lowing a significant period of time for the chemical to lubricate the threads before attempting to disassemble. 1. Unbolt the flange located just in front of the rear muffler as shown in. (figure 1) 2. Lubricate all the hangers and rubber isolators. 3. Using a muffler stand or an additional person to hold the rear muffler into position, remove the hangers from the rub- ber isolators and remove the rear muffler from the vehicle as shown. (figure 2) 4. Unbolt the flange located just behind the catalytic converter as shown. (figure 3) 5. Place hardware and gasket to the side for use during the installation of your new exhaust system. Using a muffler stand or an additional person to hold the front muffler assembly into position, remove the bolt from the rubber isolator and remove the front muffler assembly from the vehicle as shown. (figure 4) 1. Using the original hardware and gasket, place the muffler assembly into position as shown. Hand tighten the hardware for now. (figure 5) 2. Place a clamp over the expanded end of the intermediate pipe and set it into position as shown making sure to install the hanger into the rubber isolator. Do Not tighten the clamp. (figure 6) 3. Place a clamp over the expanded end of the tail pipe assem- bly and set it into position as shown making sure to install the hangers into the rubber isolators. Do Not tighten the clamp. (figure 7) 4. Check your exhaust system for proper clearance under the vehicle and also for tip alignment.

MITSUBISHI MONTERO SPORT 1997-2004 VEHICLE WIRING DIAGRAM

0

Filed Under (Mitsubishi) by admin on 06-11-2009

WIRING INFORMATION: 1997 Mitsubishi Montero Sport WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE WHITE Ignition Harness
STARTER WIRE BLACK/YELLOW or BLACK/BLUE Ignition Harness IGNITION WIRE BLACK/WHITE Ignition Harness ACCESSORY WIRE BLUE/RED Ignition Harness

download