mitsubishi lancer control panel assy


You are searching repair manual in PDF format about mitsubishi lancer control panel assy use another keyword for search another post or files



  mitsubishi lancer control panel assy Direct Download speed 5787 Kb/s

  mitsubishi lancer control panel assy Full Version speed 6767 Kb/s




1999 Dodge Durango Dashboard / Instrument Panel: Service and Repair Instrument Panel Assembly Replacement

0

Filed Under (Dodge) by admin on 17-08-2010

download
NOTE: Before starting this procedure, be certain to turn the steering wheel until the front wheels are in the straight-ahead position. 1. 2. 3. 4. 5. Disconnect and isolate the battery negative cable. Remove the trim from the right and left front door sills. Remove the trim from the left and right cowl side inner panels. Remove the steering column opening cover from the instrument panel. See: Steering Column Opening Cover and Knee Blocker Replacement Remove the two screws that secure the inside hood latch release handle to the instrument panel lower reinforcement and lower the release handle to the floor. Disconnect the driver side airbag module wire harness connector from the instrument panel wire harness at the instrument panel lower reinforcement. If the vehicle is so equipped, disconnect the overdrive lockout switch wire harness connector from the instrument panel wire harness near the instrument panel lower reinforcement. Remove the steering column from the vehicle, but do not remove the driver side airbag module, the steering wheel, or the switches from the steering column. Be certain that the steering wheel is locked and secured from rotation to prevent the loss of clockspring centering. Refer to Steering and Suspension/Steering/Steering Column/Service and Repair. See: Steering and Suspension/Steering/Steering Column/Service and Repair From under the driver side of the instrument panel, perform the following: a. Remove the screw from the center of the headlamp and dash to instrument panel bulkhead wire harness connector and disconnect the connector. b. Disconnect the two body wire harness connectors from the two instrument panel wire harness connectors that are secured to the outboard side of the instrument panel bulkhead connector. c. Disconnect the three wire harness connectors (one from the body wire harness, and two from the headlamp and dash wire harness) from the three junction block connector receptacles located closest to the dash panel. d. Unsnap the plastic retainer clip that secures the park brake release linkage rod to the lever on the back side of the park brake release handle and disengage the linkage rod end from the lever on the handle. e. Disconnect the instrument panel wire harness connector from the stop lamp switch connector receptacle. f. Disconnect the vacuum harness connector located near the left end of the heater-A/C housing. Remove the center support bracket from the instrument panel. See: Instrument Panel Center Support Bracket Replacement Remove the screw that secures the instrument panel wire harness ground eyelets to the left side of the Airbag Control Module (ACM) mount on the floor panel transmission tunnel. Disconnect the instrument panel wire harness connector from the ACM connector receptacle. Remove the glove box from the instrument panel. Refer to Body and Frame/Interior Trim/Glove Compartment/Service and Repair. See: Glove Compartment/Service and Repair Reaching through the instrument panel glove box opening, perform the following: a. Disconnect the two halves of the radio antenna coaxial cable connector near the center of the lower instrument panel glove box opening. b. Disengage the antenna half of the radio antenna coaxial cable from the retainer clip near the outboard side of the lower instrument panel glove box opening. c. Disconnect the blower motor wire harness connector located near the heater-A/C housing support brace on the inboard side of the instrument panel glove box opening. From under the passenger side of the instrument panel, perform the following: a. If the vehicle is so equipped, disconnect the two instrument panel wire harness connectors from the Infinity speaker amplifier connector receptacles on the right cowl side inner panel. b. Remove the nut that secures the instrument panel wire harness radio ground eyelet to the stud on the right cowl side inner panel. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15.

Related entry:

conector harnes control modulo A/C NISSAN Versa 2007, 2001 ford focus zx3 drivers side fuse, 1993 ford e 250 fuse panel, OBD wire colors for 2001 dodge durango 4 7 engine, replacing gear indicator cable on 2006 ford freestar, FORD ECONOLINE 1999 150 RELAYS DIAGRAM FRONT ELECTRICAL PANEL, 1998towncarfuseboxunderhood, 1999 bmw 323i fuse box diagram, slk 230 lower cover right, diagram of fuse panel for 1992 chev S-10 blazer,

2003 MITSUBISHI LANCER EVOLUTION VIII SERVICE MANUAL

0

Filed Under (Mitsubishi) by admin on 05-01-2011

download
This manual is designed for use with the 2003 LANCER EVOLUTION VIII Service Manual Volume 2, and Volume 3, and the 2003 LANCER EVOLUTION VIII Body Repair Manual to provide complete service information for the 2003 LANCER EVOLUTION VIII. Service or maintenance of any SRS component or SRS-related component must be performed only at an authorized MITSUBISHI dealer. MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B, Supplemental Restraint System (SRS), before beginning any service or maintenance of any component of the SRS or any SRS-related component. • •

Related entry:

Mitsubishi Diamante 2001 2002 2003 2004 2005 Service Repair Manual Download, mitsubishi space star manual free download, wiring diagram for 2002 mitsubishi lancer gls free download, ck4 4g92 lancer manual, 4g15a, 2004 mitsubishi lancer oz rally repair manual, where is transmission fill plug for mitsubishi lancer 1997 glxi, removing the seats mitsubishi lancer 2002 oz, owners manual for mitsubishi 1999 diamante, mitsubshi Lancer carburettor manual,

Mitsubishi Lancer Short Throw Shifter Installation Manual

0

Filed Under (Mitsubishi) by admin on 24-12-2010

download
Mitsubishi Lancer Evolution IV, V, VI, VII, VIII Mitsubishi Lancer FWD 2001 and up Mitsubishi Eclipse 2000 and up Estimated Installation Time: 30-45 Minutes Tools Required: -Philips head screwdriver -8mm wrench -10mm wrench -12mm wrench -8mm, 10mm, and 12mm sockets and ratchet -Bench vise -Grinder 1. Carefully unscrew the stock shift knob. 2. Remove ashtray and screw beneath it. 3. Remove two screws from inside the center console storage compartment. 4. Lift up on the rear section of the center console and unclip it from the front section. 5. Remove plastic screw from the driver’s side of the center console (near the gas pedal). Remove the plastic cover and the pop rivet beneath it. Then remove the two screws at the rear of the console (were hidden by the rearward part of the center console that was removed). 6. Unclip plastic connector at the rear of the console. Remove entire center console. 7. Loosen and remove the bolts at the front and rear of the plastic assembly. Note the order these parts are in as they must be replaced in the same order later in the installation. The front bolt does not need to be completely removed from the plastic assembly, only pulled out enough to allow the top part of the plastic assembly to be lifted off. Now remove the top of the assembly exposing the top of the shifter main pivot ball. 8. Remove the clip on the bottom of the shifter, which connects it to the lower shifter cable. Remove the plastic pivot cup from the lower shifter cable. Also remove the clip attaching the left side shifter cable to the shifter arm. The stock shifter can now be removed. 9. For an Evolution 8 follow this step: using a grinder, shave down the sides of the counterweight / boot support in order to remove the white plastic cup. This in no way damages the stock shifter and it is still usable after the procedure. This enables you to remove the white plastic retaining ring without any cutting.

Related entry:

remove middle console from a 2002 mitsubishi Lancer, 06 chevy aveo Short Shifter plastic bushing, 2003 lancer oz rally shifter linkage schematic, how to remove your gear selector on a Montero, manual gear shifter for Mitsubishi EVO VIII, mitsubishi 2001 engine 4g15 gdi obd cods p0110, montero shift lever diagram,

1999 Dodge Grand Caravan Trim Panel: Service and Repair REMOVAL INSTALLATION

0

Filed Under (Dodge) by admin on 20-09-2010

download
Trim Panel: Service and Repair REMOVAL 1. Using a trim stick (C-4755), pry courtesy lamp from door trim. 2. Disconnect wire connector from courtesy lamp. 3. If equipped, remove screws attaching door assist handle to inner door panel. 4. If equipped, remove screw attaching door pull cup to inner door panel. 5. If equipped, remove screws attaching trim panel to door from below map pocket. 6. If equipped, remove window crank. 7. Using a trim stick, remove screw cover from switch panel. 8. Remove screws attaching switch panel to door trim. 9. Remove power accessary switch from door trim. 10. Disconnect power switch from wire connector. 11. If equipped, using a small, flat bladed pry tool, remove memory seat/mirror switch and disconnect wire connector. 12. If equipped, remove screw holding door trim to door panel from behind inside latch release handle. 13. Disengage clips attaching door trim to door frame around perimeter of panel. 14. Lift trim panel upward to disengage flange from inner belt molding at top of door. 15. Tilt top of trim panel away from door to gain access to latch linkage. 16. Disengage clip attaching linkage rod to inside latch release handle. 17. Separate linkage rod from latch handle. 18. Remove front door trim panel from vehicle. INSTALLATION 1. Hold top of trim panel away from door to gain access to latch linkage. 2. Place linkage rod in position on latch handle. 3. Engage clip to hold linkage rod to inside latch release handle. 4. Place front door trim panel in position on door. 5. Install trim panel into inner belt molding at top of door. 6. Install clips to attach door trim to door frame around perimeter of panel. 7. If equipped, install screw to attach door trim to door panel behind inside latch release handle. 8. If equipped, connect power switch into wire connector. 9. Place power accessary switch in position on door trim. 10. Connect wire connector into memory seat/mirror switch and install switch into trim panel. 11. Install screws to attach accessary switch panel to door trim. 12. Install screw cover into switch panel. 13. If equipped, install window crank. 14. If equipped, install screws to attach trim panel to door inside map pocket. 15. If equipped, install screw to attach door pull cup to inner door panel. 16. If equipped, install screws to attach door assist handle to inner door panel. 17. Connect wire connector into courtesy lamp. 18. Install lamp in door trim.

Related entry:

yhs-looksafe_ds_trans, astra mk 5 door panel removal, how to changa exterior handle on 1997 acura rl, fix nissan van side door, 1995 honda odyssey door panel rmovall, 2005 mercedes ml350 remove door panel, How to take the iner drive side door lone off 2006 Kia Sorento ?, door latch lock switch ohm value 2005 cobalt, removing doorbpanel warranty on 2008 impala, 2002 acura mdx removing door panels,

2000 Toyota Corolla CE Heating and Air Conditioning Control Assembly Removal and Installation

0

Filed Under (Toyota) by admin on 06-05-2011

download
12. REMOVE A/C CONTROL ASSEMBLY Remove the 2 screws and pull out the A/C control assembly, then disconnect the connector. NOTE: Be careful not to vent the mode control cable, when pull out the A/C control assembly. INSTALLATION 1. INSTALL A/C CONTROL ASSEMBLY a. Connect the connector. b. Pass the heater control cables as shown in the illustration. COMPONENTS REMOVAL 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. REMOVE COWL SIDE TRIMS REMOVE FRONT DOOR SCUFF PLATES REMOVE LOWER FINISH PANEL REMOVE LOWER INSERT PANEL REMOVE CENTER CLUSTER FINISH PANEL REMOVE HEATER TO RESISTOR NO.2 DUCT REMOVE LOWER PANEL REMOVE REAR CONSOLE BOX REMOVE SHIFTING HOLE BEZEL REMOVE FINISH LOWER CENTER PANEL 11. DISCONNECT HEATER CONTROL CABLE c. Install the 2 set screws. 2. CONNECT HEATER CONTROL CABLES a. Set Air inlet control lever at “RECIRC” position b. Set Temperature control dial at “MAX. COOL” position c. Set Mode control dial at “DEF” position Zoom d. Adjust air inlet control cable. Set air inlet damper control lever to “RECIRC” position and connect the inner cable to lever pin and clamp the outer cable. HINT: Lock the clamp while lightly pushing the outer cable to the direction shown by arrow in the illustration. Sized for Print Zoom e. Adjust air mix control cable. Set air mix damper control lever to “MAX. COOL” position and connect the inner cable to lever pin and clamp the outer cable. HINT: Lock the clamp while lightly pulling the outer cable to the direction shown by arrow in the illustration. Sized for Print

Related entry:

1974 duster heater control cable, 2000 lincoln traction control, 2000 saab 9-5 emissions control diagram, 2005 corolla CE vibrates wiyh low idle, Chassis Control Box, diagtam of where the upper and lower crankshaft sensor go on a 2000 deville, toyota corolla 2008 air mix control cable,