monza engine timing


You are searching repair manual in PDF format about monza engine timing use another keyword for search another post or files



  monza engine timing Direct Download speed 5787 Kb/s

  monza engine timing Full Version speed 6767 Kb/s




2006 Mazda5 BODY VIBRATION AT CRUISE SPEED

0

Filed Under (Mazda) by admin on 16-06-2011

download
DESCRIPTION Some vehicles may experience a body vibration when driving approximately 55mph. This symptom is due to the characteristics of the No. 3 & No. 4 engine mounts. Modified No. 3 & No. 4 engine mounts have been established for service only. Customers having this concern should have their vehicle repaired using the following repair procedure. REPAIR PROCEDURE IMPORTANT NOTE: • This repair should only be performed if all tires and rims are confirmed to be in balance and all suspension components are in proper working condition. • Notify customers that use of the modified mounts will reduce vibration at cruising speed but may increase vibration at idle. NOTE: Because idle vibration may increase, it is highly recommended to continue using mass production mounts for all other service concerns. 1. Verify concern. 2. Replace the No. 3 & 4 engine mounts with service parts according to the appropriate Workshop Manual section 01-10 ENGINE REMOVAL/INSTALLATION. 3. Center the new engine mounts as outlined in ENGINE MOUNT CENTERING PROCEDURE. 4. Verify repair. ENGINE MOUNT CENTERING PROCEDURE No. 1, No. 3 and No. 4 Engine Mount Adjustment 1. Warm up the engine. 2. Raise and support vehicle on a hoist. 3. Remove engine under cover. 4. Lower the vehicle until the front tires lightly touch the ground. 5. Secure the engine and transaxle using an engine jack and attachment as instructed in No.3 Engine Mount And No.4 Engine Mount Rubber Installation Note in appropriate Workshop Manual, section 01-10 MECHANICAL. 6. Remove two bolts from No. 3 engine mount bracket. REMOVE THE BOLTS 7. Lift engine using jack until No.3 engine mount is lifted slightly from vehicle body. NOTE: • Do not raise engine too much or A/C pipe damage may occur. 8. Move the engine mount rubber or engine until installation hole on the vehicle body aligns with hole in the engine mount bracket. ENGINE MOUNT BRACKET 1532c SHOWN BEFORE ALIGNING THE HOLES SHOWN AFTER ALIGNING THE HOLES 9. Lower the jack and tighten bolts on No. 3 engine mount bracket. Tightening torque: 55.0-77.3 ft-lbf (74.5-04.9 N.m) NOTE: 10. With engine supported as described in STEP 5, remove four (4) nuts and two (2) bolts from No. 4 engine mount top plate. Remove top plate. NOTE: 11. Lift engine again using jack until No.4 engine mount is lifted slightly from vehicle body. NOTE: 12. With top plate of No. 4 engine mount removed, move engine mount bottom plate or engine until all four (4) installation studs on the vehicle align with the engine mount holes. • Do not allow the engine mount bracket to be misaligned. • To access the mount, remove battery box. • Do not raise engine too much or A/C pipe damage may occur. ALIGN THE 4 STUDS IN THE PLATE HOLES 13. Place top plate back on and tighten No. 4 engine mount bracket nuts and bolts to torque indicated. Tightening torque: A.32.5-45.0 ft-lbf (44.0-61.0 N.m) B.61.1-86.7 in-lbf (6.9-9.8 N.m) TIGHTEN BOLTS IN SEQUENCE SHOWN 1532e 14. Lift engine again using jack and loosen the two bolts on the No. 1 engine mount rubber until slightly loose on the No. 1 engine mount rubber.

Related entry:

opel corsa 1 3 1997 engine, nissan ka20 engine manual free, FOUR main harmful constituents of petrol engine exhaust emissions, nissan yd25 engine workshop manuals, 2002 dodge ram 1500 4 7 engine vacuum hose diagram, s10 2 2l camshaft exploded view, Chevy 454 Engine Manual, toyota tundra forum 5 7 timing chain diagram, timing marks 2000 echo, ford ka engine layout,

2GR-FE Engine Ticking Noise and/or MIL “ON” P0014, P0015, P0024, P0025, P0017, or P0018

0

Filed Under (Toyota) by admin on 20-05-2011

download
Introduction IMPORTANT It is mandatory that the VVT-i gear actuator bolts, actuator center section alignment, and actuator body be inspected BEFORE performing this TSB. If no concerns are noted with these parts, this TSB does NOT apply. Some 2005 – 2009 model year vehicles with 2GR-FE engines may exhibit a ticking/clicking type noise from the cylinder head cover area which may be accompanied by a MIL “ON” and one or more VVT-i related Diagnostic Trouble Codes (DTCs). Please use the following repair procedure to address customer concerns. Inspection Procedure 1. Start the engine and listen for any ticking/clicking type noises coming from the VVT-i gear area of the engine. NOTE This condition may or may not be accompanied by one or more of the following DTCs stored in the Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM): • P0014: Camshaft Position “B” – Timing Advanced or System Performance (Bank 1) • P0015: Camshaft Position “B” Timing Over Retarded (Bank 1) • P0017: Crankshaft Position Camshaft Position Correlation (Bank 1 Sensor B) • P0018: Crankshaft Position Camshaft Position Correlation (Bank 2 Sensor A) • P0024: Camshaft Position “B” – Timing Over-Advanced or System Performance (Bank 2) • P0025: Camshaft Position “B” – Timing Over-Retarded (Bank 2) 2. Remove the cylinder head cover and inspect the exhaust VVT-i gear assembly on the affected cylinder bank. NOTE If NO concerns are found with the VVT-i gear actuator bolts, the actuator center section alignment, or actuator body, this TSB does NOT apply. Refer to Repair Manual procedures for further diagnosis. Repair Procedure 1. If any concerns are noted with the exhaust VVT-i gear bolts or actuator follow the four steps below: A. Replace the camshaft housing sub-assembly, exhaust camshaft, and exhaust VVT-i gear assembly on the affected bank. B. Inspect the intake VVT-i gear assembly and bolts on the affected bank. Replace the intake VVT-i gear assembly if necessary. C. Inspect the opposite bank exhaust VVT-i gear actuator and bolts. If any concerns are noted replace the opposite bank camshaft housing sub-assembly, exhaust camshaft, and exhaust VVT-i gear assembly. D. Inspect the opposite bank intake gear actuator assembly and bolts. Replace the intake VVT-i gear assembly if necessary. For complete disassembly procedures refer to the Technical Information System (TIS), applicable model and model year Repair Manual: • 2005 Avalon: Engine/Hybrid System – Engine Mechanical – “Engine Mechanical: Camshaft (LH Bank) / (RH Bank) (2GR-FE): Replacement” • 2006 / 2007 / 2008 / 2009 Avalon: Engine/Hybrid System – Engine Mechanical – “2GR-FE Engine Mechanical: Engine Unit: Disassembly” • 2007 / 2008 / 2009 Camry: Engine/Hybrid System – Engine Mechanical – “2GR-FE Engine Mechanical: Engine Unit: Disassembly” • 2008 / 2009 Highlander: Engine/Hybrid System – Engine Mechanical – “2GR-FE Engine Mechanical: Engine Unit: Disassembly” • 2006 / 2007 / 2008 / 2009 RAV4: Engine/Hybrid System – Engine Mechanical – “2GR-FE Engine Mechanical: Engine Unit: Disassembly”

Related entry:

2005 cadillac srx v6 codes p0021 p0024 no start, 2008 honda passport motor noise from top end, 2009 toyota corolla VVTI Intake actuator, 4HF1 isuzu camgear marks, gear noise engine, Gearbox probox, installing camshaft gears on 2001 pt cruiser 2 4l, jaguar right hand bank vvt clickung,

2003 TOYOTA TACOMA TIMING BELT INSTALLATION REMOVAL

0

Filed Under (Toyota) by admin on 13-01-2011

download
NOTICE: Always turn the crankshaft clockwise. (c) Check that the timing marks of the camshaft timing pul- leys and No.3 timing belt cover are aligned. If not, turn the crankshaft pulley 1 revolution (360°). (d) Remove the crankshaft pulley bolt. IF REUSING TIMING BELT, CHECK INSTALLATION MARKS ON TIMING BELT Check that there are 3 installation marks and front mark on the timing belt. If the installation and front marks have disappeared, before re- moving the timing belt, place 3 new installation marks on the timing belt to match the timing marks of the timing pulleys, and place a new front mark on the timing belt. 18. 19. REMOVE TIMING BELT TENSIONER Alternately loosen the 2 bolts, and remove them, the belt ten- sioner and dust boot. 20. REMOVE TIMING BELT 21. (a) REMOVE RH CAMSHAFT TIMING PULLEY Using SST, loosen the pulley bolt. SST 09960–10010 (09962–01000, 09963–01000) Remove the bolt, knock pin and timing pulley. (b) 22. (a) REMOVE LH CAMSHAFT TIMING PULLEY Using SST, loosen the pulley bolt. SST 09960–10010 (09962–01000, 09963–01000) Remove the bolt, knock pin and timing pulley. (b) 23. REMOVE NO.2 IDLER PULLEY Remove the bolt and idler pulley. 24. REMOVE NO.1 IDLER PULLEY Using a 10 mm hexagon wrench, remove the pivot bolt, idler pulley and plate washer. 25. REMOVE CRANKSHAFT TIMING PULLEY Remove the timing pulley. HINT: If the pulley cannot be removed by hand, use SST and a service bolt to remove the timing pulley. SST 09950–50011 (09951–05010, 09952–05010, 09953–05020, 09954–05011)

Related entry:

04 mercury gran victoria 4 6 timing mark, NissanXtrail 2 5 timing mark, vw combi 2 1 timing, volvo s40 cam belt replacement manual, which tappets should match with mark when timing l18 engine, vw polo 1 6 1999 cam timing marks procedure, ford tx5 v6 timing marks, 2003 chevy tracker timing installation viedos, 6g74 01 cam timing marks, sentra 96 lining timing marks up,

1995 Ford Windstar Engine Front Cover REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 06-04-2011

download
Engine Front Cover If the engine front cover (6019) is being removed to check timing chain deflection, refer to Timing Chain Deflection Procedure as outlined in Section 03-00. SPECIAL SERVICE TOOL(S) REQUIRED Description Crankshaft Damper Remover Vibration Damper and Seal Replacer T82L-6316-A Vibration Damper Remover Adapter Removal 1. Remove engine (6007) from vehicle. Refer to procedure in this section. 2. Loosen drive belt tensioner (6B209) and drive belt (8620) . 3. Remove water pump pulley retaining bolts and water pump pulley (8509) . 4. Remove retaining bolts and disconnect heater water outlet tube (18663) from water pump (8501) . 5. Disconnect electrical connector at camshaft position sensor. 6. Disconnect electrical connector at crankshaft position sensor (CKP sensor) (6C315) . 7. Remove retaining bolt and disconnect radiator lower hose tube (8291) from water pump . NOTE: If the vibration damper and crankshaft pulley have to be separated, mark the vibration damper and crankshaft pulley so that they may be reassembled in the same relative position. This is important as the vibration damper and crankshaft pulley are initially balanced as a unit. NOTE: If the vibration damper is being replaced, check if the original vibration damper has balance pins installed. If so, new balance pins (6A328 or equivalent) must be installed on the new vibration damper in the same position as the original vibration damper. The crankshaft pulley (new or original) must also be installed in the same relative position as originally installed. 8. Remove crankshaft pulley (6312) and vibration damper assembly using Crankshaft Damper Remover T58P-6316-D and Vibration Damper Remover Adapter T82L-6316-B. 9. Remove four retaining bolts and remove brace from A/C bracket and P/S bracket. 10. Remove oil bypass filter (6714) . Tool Number T58P-6316-D T82L-6316-B CAUTION: The engine front cover cannot be removed without lowering the oil pan (6675) . 11. Remove oil pan . Refer to procedure in this section. CAUTION: Do not overlook the engine front cover retaining bolt located behind the oil pump and filter body (6603) . The engine front cover will break if pried upon and all retaining bolts are not removed. 12. Remove engine front cover retaining bolts. It is not necessary to remove water pump . 13. Remove engine front cover and water pump as an assembly. 14. Remove engine front cover gasket and discard. Water Pump Tightening Sequence Installation NOTE: Lightly oil all bolt and stud bolt threads before installation except those specifying special sealant. 1. Clean gasket surfaces on the engine front cover and cylinder block (6010) . If reusing the engine front cover , replace crankshaft front seal (6700) . Refer to Crankshaft Pulley and/or Damper and/or Crankshaft Front Seal in this section. 2. If a new engine front cover is to be installed: Install oil pump and filter body . Clean water pump gasket surface. Position a new water pump housing gasket (8507) on the engine front cover and install water pump . Install water pump retaining bolts. Tighten to 20-30 Nm (15-22 lb-ft). 3. Lubricate crankshaft front seal with clean engine oil XO-10W30-QSP or -DSP or equivalent meeting Ford specification ESE-M2C153-E. NOTE: Gasket and Trim Adhesive D7AZ-19B508-B or equivalent meeting Ford specification ESE-M2G52-A is recommended to hold the engine front cover gasket (6020) in position while the engine front cover is installed. 4. Position a new engine front cover gasket on the cylinder block and install the engine front cover / water pump assembly using dowels for proper alignment. 5. Install the engine front cover retaining bolts. Tighten to 20-30 Nm (15-22 lb-ft). Install the capscrew (Part No. N804841) nearest the oil bypass filter flange last, and tighten last. Apply Loctite® or equivalent to bolt prior to installation. Refer to illustration under Step 13 of removal procedure. 6. Install oil pan as outlined. 7. Install oil bypass filter . 8. Coat pulley sealing surface with clean engine oil XO-10W30-QSP or -DSP or equivalent meeting Ford specification ESE-M2C153-E. NOTE: When using silicone rubber sealer, assembly must occur within 15 minutes after sealer application. After this time, the sealer may start to setup, and its sealing effectiveness may be reduced. 9. Apply a small amount of Silicone Gasket and Sealant F1AZ-19562-A or equivalent meeting Ford specification WSE-M4G320-A2 to crankshaft keyway. 10. Position crankshaft key (6B316) in the crankshaft keyway.

Related entry:

how to remove the tappet cover on 1kd, 2000 mercedesbenz ml320 front engine cover removal, Replacing valve cover gasket on a 1997 E 420 Mercedes, 2006 bmw 525i e60 cylinder head gasket replaced after cranking but no start, 03 vw passat 1 9tdi rocker cover pressurising, how to remove the plastic cover over the engine on a 2007 avalanche, how to remove plastic cover over fuel injectors on a 2007 avalanche, ml320 valve cover remove, Northstar Valve Cover Gasket Replacement, how to remove intake cover on a 2006 equinox,

1996 Mitsubishi Eclipse GS-T TIMING BELT & BALANCE SHAFT BELT Removal

0

Filed Under (Mitsubishi) by admin on 18-01-2011

download
1. Disconnect negative battery cable. Remove engine undercover. Place wooden block between jack and oil pan, and raise engine slightly. Remove engine mount assembly near timing belt cover. 2. Remove clamp for power steering return hose near timing belt cover. Remove all drive belts and tensioner pulley bracket. See Fig. 1 . Remove power steering and water pump pulleys. Rotate crankshaft clockwise so that No. 1 cylinder is at TDC of compression stroke. Remove crankshaft pulley. CAUTION: DO NOT rotate crankshaft counterclockwise. Ensure timing marks are aligned. If reusing timing belts, mark timing belts for direction of rotation. 3. Remove upper timing belt cover and gasket. Remove stub bolt of engine support bracket, and remove center timing belt cover. Remove lower timing belt cover. NOTE: Camshaft sprocket dowel pins will be in 12 o’clock position when timing marks are correctly aligned. 4. Ensure camshaft, crankshaft and oil pump sprocket timing marks are aligned. See Fig. 2 or Fig. 3 . Loosen tensioner pulley center bolt. Move tensioner to relieve timing belt tension. Remove timing belt. Remove timing belt auto tensioner. See Fig. 1 . 5. Remove plug from left side of cylinder block. Install a .31″ (8.0 mm) diameter Phillips screwdriver into the hole against balance shaft. See Fig. 4 . Screwdriver must go in at least 2.36″ (60 mm) or more. If screwdriver will only go in about .79-.98″ (20-25 mm) before striking balance shaft, turn sprocket one revolution and align timing mark. Keep screwdriver in place until timing belt is installed. This ensures balance shaft driven by oil pump sprocket remains in correct position. 6. To remove timing belt “B” (balance shaft belt), hold crankshaft sprocket stationary with a spanner wrench. Remove crankshaft sprocket bolt. Using gear puller, remove outer crankshaft sprocket. 7. Remove crankshaft sensing blade (if equipped). See Fig. 5 . Loosen timing belt “B” tensioner bolt. If reusing timing belt “B”, mark direction of belt rotation for reassembly reference. Remove timing belt “B”.

Related entry:

1996 Isuzu Trooper crank pulley removal, bmw 320 d n47d20 balance shaft locking tool, beltrotation2003eclipse, timing marks for 1997 cadillac north star, balance shaft timing 2 2ltr ecotech, 03 cts timimg belt cover removal, installing timing belt on mitsubishi 4 d 56, mitsubishi eclipse timing marks diagram turn clockwise, nissan vanette LD 22 proper timing mark, peugeot 307 timing marks,