nissan cefiro A32 engine specs


You are searching repair manual in PDF format about nissan cefiro A32 engine specs use another keyword for search another post or files



  nissan cefiro A32 engine specs Direct Download speed 5787 Kb/s

  nissan cefiro A32 engine specs Full Version speed 6767 Kb/s




2006 Mazda5 BODY VIBRATION AT CRUISE SPEED

0

Filed Under (Mazda) by admin on 16-06-2011

download
DESCRIPTION Some vehicles may experience a body vibration when driving approximately 55mph. This symptom is due to the characteristics of the No. 3 & No. 4 engine mounts. Modified No. 3 & No. 4 engine mounts have been established for service only. Customers having this concern should have their vehicle repaired using the following repair procedure. REPAIR PROCEDURE IMPORTANT NOTE: • This repair should only be performed if all tires and rims are confirmed to be in balance and all suspension components are in proper working condition. • Notify customers that use of the modified mounts will reduce vibration at cruising speed but may increase vibration at idle. NOTE: Because idle vibration may increase, it is highly recommended to continue using mass production mounts for all other service concerns. 1. Verify concern. 2. Replace the No. 3 & 4 engine mounts with service parts according to the appropriate Workshop Manual section 01-10 ENGINE REMOVAL/INSTALLATION. 3. Center the new engine mounts as outlined in ENGINE MOUNT CENTERING PROCEDURE. 4. Verify repair. ENGINE MOUNT CENTERING PROCEDURE No. 1, No. 3 and No. 4 Engine Mount Adjustment 1. Warm up the engine. 2. Raise and support vehicle on a hoist. 3. Remove engine under cover. 4. Lower the vehicle until the front tires lightly touch the ground. 5. Secure the engine and transaxle using an engine jack and attachment as instructed in No.3 Engine Mount And No.4 Engine Mount Rubber Installation Note in appropriate Workshop Manual, section 01-10 MECHANICAL. 6. Remove two bolts from No. 3 engine mount bracket. REMOVE THE BOLTS 7. Lift engine using jack until No.3 engine mount is lifted slightly from vehicle body. NOTE: • Do not raise engine too much or A/C pipe damage may occur. 8. Move the engine mount rubber or engine until installation hole on the vehicle body aligns with hole in the engine mount bracket. ENGINE MOUNT BRACKET 1532c SHOWN BEFORE ALIGNING THE HOLES SHOWN AFTER ALIGNING THE HOLES 9. Lower the jack and tighten bolts on No. 3 engine mount bracket. Tightening torque: 55.0-77.3 ft-lbf (74.5-04.9 N.m) NOTE: 10. With engine supported as described in STEP 5, remove four (4) nuts and two (2) bolts from No. 4 engine mount top plate. Remove top plate. NOTE: 11. Lift engine again using jack until No.4 engine mount is lifted slightly from vehicle body. NOTE: 12. With top plate of No. 4 engine mount removed, move engine mount bottom plate or engine until all four (4) installation studs on the vehicle align with the engine mount holes. • Do not allow the engine mount bracket to be misaligned. • To access the mount, remove battery box. • Do not raise engine too much or A/C pipe damage may occur. ALIGN THE 4 STUDS IN THE PLATE HOLES 13. Place top plate back on and tighten No. 4 engine mount bracket nuts and bolts to torque indicated. Tightening torque: A.32.5-45.0 ft-lbf (44.0-61.0 N.m) B.61.1-86.7 in-lbf (6.9-9.8 N.m) TIGHTEN BOLTS IN SEQUENCE SHOWN 1532e 14. Lift engine again using jack and loosen the two bolts on the No. 1 engine mount rubber until slightly loose on the No. 1 engine mount rubber.

Related entry:

qg15 engine workshop manual, yhsm-mobile, Chevy 454 Engine Manual Download, 2l te engine repair manual, 1az fse D4 engine layout bank 2 sensor 1, how many liters of oil in an F6 engines for multicab, what does fuse box under bonnet control on renault trafic, toyota 1az-fe engine timing procedure, 2005 Trailblazer Engine Diagram, 12r gasoline engine repair manual,

2000-2001 Nissan Maxima Engine rough running Engine surging Low engine power

0

Filed Under (Nissan) by admin on 21-12-2010

download
SERVICE INFORMATION If an applied vehicle has DTC P0100 stored and possibly exhibits, • • • Engine rough running Engine surging Low engine power the cause may be an airflow sensor that has been damaged by air-ingested dust/dirt. To resolve this incident, if it should occur, follow the steps outlined in the Service Procedure on page 2. Service Procedure Summary: • Remove dust/dirt/debris from inside the air cleaner housing. This will help prevent another incident. • A new genuine Nissan air filter element must be used for all warranty claims, and any other claim for which Nissan pays. A new genuine Nissan air filter element is designed to be compatible with the Nissan air flow meter and has proven to provide adequate dust protection to help prevent these incidents. It is strongly recommended that incident customers continue using Nissan genuine air filters for assured protection when replacing according to the routine maintenance schedule. See parts information for the air filter part number (P/N). • Install a new complete airflow meter assembly. See Parts Information for the part number (P/N). • Reprogram the ECM with special new data that is matched to the different output characteristics of the new airflow meter.

Related entry:

2005 nissan maxima surges when engine warms up, nissan maxima V6 engine surges, rpm surges nissan maxima,

2GR-FE Engine Ticking Noise and/or MIL “ON” P0014, P0015, P0024, P0025, P0017, or P0018

0

Filed Under (Toyota) by admin on 20-05-2011

download
Introduction IMPORTANT It is mandatory that the VVT-i gear actuator bolts, actuator center section alignment, and actuator body be inspected BEFORE performing this TSB. If no concerns are noted with these parts, this TSB does NOT apply. Some 2005 – 2009 model year vehicles with 2GR-FE engines may exhibit a ticking/clicking type noise from the cylinder head cover area which may be accompanied by a MIL “ON” and one or more VVT-i related Diagnostic Trouble Codes (DTCs). Please use the following repair procedure to address customer concerns. Inspection Procedure 1. Start the engine and listen for any ticking/clicking type noises coming from the VVT-i gear area of the engine. NOTE This condition may or may not be accompanied by one or more of the following DTCs stored in the Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM): • P0014: Camshaft Position “B” – Timing Advanced or System Performance (Bank 1) • P0015: Camshaft Position “B” Timing Over Retarded (Bank 1) • P0017: Crankshaft Position Camshaft Position Correlation (Bank 1 Sensor B) • P0018: Crankshaft Position Camshaft Position Correlation (Bank 2 Sensor A) • P0024: Camshaft Position “B” – Timing Over-Advanced or System Performance (Bank 2) • P0025: Camshaft Position “B” – Timing Over-Retarded (Bank 2) 2. Remove the cylinder head cover and inspect the exhaust VVT-i gear assembly on the affected cylinder bank. NOTE If NO concerns are found with the VVT-i gear actuator bolts, the actuator center section alignment, or actuator body, this TSB does NOT apply. Refer to Repair Manual procedures for further diagnosis. Repair Procedure 1. If any concerns are noted with the exhaust VVT-i gear bolts or actuator follow the four steps below: A. Replace the camshaft housing sub-assembly, exhaust camshaft, and exhaust VVT-i gear assembly on the affected bank. B. Inspect the intake VVT-i gear assembly and bolts on the affected bank. Replace the intake VVT-i gear assembly if necessary. C. Inspect the opposite bank exhaust VVT-i gear actuator and bolts. If any concerns are noted replace the opposite bank camshaft housing sub-assembly, exhaust camshaft, and exhaust VVT-i gear assembly. D. Inspect the opposite bank intake gear actuator assembly and bolts. Replace the intake VVT-i gear assembly if necessary. For complete disassembly procedures refer to the Technical Information System (TIS), applicable model and model year Repair Manual: • 2005 Avalon: Engine/Hybrid System – Engine Mechanical – “Engine Mechanical: Camshaft (LH Bank) / (RH Bank) (2GR-FE): Replacement” • 2006 / 2007 / 2008 / 2009 Avalon: Engine/Hybrid System – Engine Mechanical – “2GR-FE Engine Mechanical: Engine Unit: Disassembly” • 2007 / 2008 / 2009 Camry: Engine/Hybrid System – Engine Mechanical – “2GR-FE Engine Mechanical: Engine Unit: Disassembly” • 2008 / 2009 Highlander: Engine/Hybrid System – Engine Mechanical – “2GR-FE Engine Mechanical: Engine Unit: Disassembly” • 2006 / 2007 / 2008 / 2009 RAV4: Engine/Hybrid System – Engine Mechanical – “2GR-FE Engine Mechanical: Engine Unit: Disassembly”

Related entry:

2003 saturn vue 3 0 bank 2, 98 Buick ticking noise, air conditioner actuator in an f 150 2009, clicking sound on 2003 toyota corolla, serpentine belt diagram 08 toyota highlander 3 5 liter engine, ticking sound in motor of 2002 taurus, vvt-i v6 3 3,

1995 Ford Windstar Engine Front Cover REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 06-04-2011

download
Engine Front Cover If the engine front cover (6019) is being removed to check timing chain deflection, refer to Timing Chain Deflection Procedure as outlined in Section 03-00. SPECIAL SERVICE TOOL(S) REQUIRED Description Crankshaft Damper Remover Vibration Damper and Seal Replacer T82L-6316-A Vibration Damper Remover Adapter Removal 1. Remove engine (6007) from vehicle. Refer to procedure in this section. 2. Loosen drive belt tensioner (6B209) and drive belt (8620) . 3. Remove water pump pulley retaining bolts and water pump pulley (8509) . 4. Remove retaining bolts and disconnect heater water outlet tube (18663) from water pump (8501) . 5. Disconnect electrical connector at camshaft position sensor. 6. Disconnect electrical connector at crankshaft position sensor (CKP sensor) (6C315) . 7. Remove retaining bolt and disconnect radiator lower hose tube (8291) from water pump . NOTE: If the vibration damper and crankshaft pulley have to be separated, mark the vibration damper and crankshaft pulley so that they may be reassembled in the same relative position. This is important as the vibration damper and crankshaft pulley are initially balanced as a unit. NOTE: If the vibration damper is being replaced, check if the original vibration damper has balance pins installed. If so, new balance pins (6A328 or equivalent) must be installed on the new vibration damper in the same position as the original vibration damper. The crankshaft pulley (new or original) must also be installed in the same relative position as originally installed. 8. Remove crankshaft pulley (6312) and vibration damper assembly using Crankshaft Damper Remover T58P-6316-D and Vibration Damper Remover Adapter T82L-6316-B. 9. Remove four retaining bolts and remove brace from A/C bracket and P/S bracket. 10. Remove oil bypass filter (6714) . Tool Number T58P-6316-D T82L-6316-B CAUTION: The engine front cover cannot be removed without lowering the oil pan (6675) . 11. Remove oil pan . Refer to procedure in this section. CAUTION: Do not overlook the engine front cover retaining bolt located behind the oil pump and filter body (6603) . The engine front cover will break if pried upon and all retaining bolts are not removed. 12. Remove engine front cover retaining bolts. It is not necessary to remove water pump . 13. Remove engine front cover and water pump as an assembly. 14. Remove engine front cover gasket and discard. Water Pump Tightening Sequence Installation NOTE: Lightly oil all bolt and stud bolt threads before installation except those specifying special sealant. 1. Clean gasket surfaces on the engine front cover and cylinder block (6010) . If reusing the engine front cover , replace crankshaft front seal (6700) . Refer to Crankshaft Pulley and/or Damper and/or Crankshaft Front Seal in this section. 2. If a new engine front cover is to be installed: Install oil pump and filter body . Clean water pump gasket surface. Position a new water pump housing gasket (8507) on the engine front cover and install water pump . Install water pump retaining bolts. Tighten to 20-30 Nm (15-22 lb-ft). 3. Lubricate crankshaft front seal with clean engine oil XO-10W30-QSP or -DSP or equivalent meeting Ford specification ESE-M2C153-E. NOTE: Gasket and Trim Adhesive D7AZ-19B508-B or equivalent meeting Ford specification ESE-M2G52-A is recommended to hold the engine front cover gasket (6020) in position while the engine front cover is installed. 4. Position a new engine front cover gasket on the cylinder block and install the engine front cover / water pump assembly using dowels for proper alignment. 5. Install the engine front cover retaining bolts. Tighten to 20-30 Nm (15-22 lb-ft). Install the capscrew (Part No. N804841) nearest the oil bypass filter flange last, and tighten last. Apply Loctite® or equivalent to bolt prior to installation. Refer to illustration under Step 13 of removal procedure. 6. Install oil pan as outlined. 7. Install oil bypass filter . 8. Coat pulley sealing surface with clean engine oil XO-10W30-QSP or -DSP or equivalent meeting Ford specification ESE-M2C153-E. NOTE: When using silicone rubber sealer, assembly must occur within 15 minutes after sealer application. After this time, the sealer may start to setup, and its sealing effectiveness may be reduced. 9. Apply a small amount of Silicone Gasket and Sealant F1AZ-19562-A or equivalent meeting Ford specification WSE-M4G320-A2 to crankshaft keyway. 10. Position crankshaft key (6B316) in the crankshaft keyway.

Related entry:

how to remove plastic engine cover 08 eqinox, how to change the valve cover gaskets on a 1999 pontiac grand am, 1999 ford mustang vibration damper bolt loose, how to take plastic cover off engine in an equinox, how to replace valve cover gaskets on a 1999 ml 430 mercedes, how to replace a valve cover gasket replacement hyundai, how to remove the front engine cover on a 2008 chevy equinox, x308 crankshaft pulley spec, how to remove decorate cover on engine 3 5 chrysler 300, how to remove a rocker cover ford ka 2004,

NISSAN PERIODIC MAINTENANCE SCHEDULE NISSAN MICRA

0

Filed Under (Nissan) by admin on 11-04-2010

download
ENGINE MAINTENANCE (Petrol Engine) Replace engine oil Replace engine oil filter Inspect drive belts Inspect cooling system
Page 1© NISSAN NISSAN PERIODI CMAINTENANCE SCHEDULE NISSAN MICRA 15,000 KM Inspect brake, clutch and automatic
trans-axle fluids Inspect manual trans-axle gear oil Inspect power steering fluid and lines Inspect brake, clutch and exhaust systems
Inspect steering gear and linkage, axle and suspension parts and front driveshafts Inspect wheel alignment (if necessary rotate
tyres and balance Inspect brake pads, rotors and other brake components Inspect brake linings, drums and other brake
components Inspect foot brake, parking brake and clutch Lubricate locks, hinges & hood latch Inspect seat belts, buckles, retractors,
anchors & adjuster Clean or replace ventilation filter Replace brake fluid (Severe conditions only)

Related entry:

fuse layout on 2005 nissan micra, c1035 fault code nissan, cg13 micra ecu pinout pdf, how to change interier light on nisson micra e 2004, micra driveshaft replace, Nissan Micra Service Schedule, replace ariel on nissan micra 2001,