nissan murano axle torque specifications


You are searching repair manual in PDF format about nissan murano axle torque specifications use another keyword for search another post or files



  nissan murano axle torque specifications Direct Download speed 5787 Kb/s

  nissan murano axle torque specifications Full Version speed 6767 Kb/s




2004 Ford F-150 Rear Axle Differential Cover Axle Shaft Oil Seal and Rear Wheel Bearing REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 28-02-2011

download
1. With the vehicle in NEUTRAL, position on a hoist. For additional information, refer to Section 100-00. 2. Remove the rear wheel and tire assembly. For additional information, refer to Section 204-00. 3. Remove the parts in the order indicated in the following illustration and table. 4. To install, reverse the removal procedure. 5. Fill the axle with the specified quantity of the specified lubricant. For additional information, refer to the Specifications in this section. Item 2: Rear Disc Brake Caliper Removal Note 1. CAUTION: Do not allow the caliper to hang from the brake hose. Provide a suitable support. Position the rear disc brake caliper aside. For additional information, refer to Section 206-00. Item 7: Differential Pinion Shaft Removal Note 1. Move the differential pinion shaft out far enough to remove the U-washers. Replace the shaft and install the lock bolt finger tight when U-washers are removed. Item 8: U-washer Removal Note 1. CAUTION: Do not damage the rubber O-rings in the axle shaft grooves. Remove the U-washers. 1. Push the axle shafts inboard. 2. Remove the U-washers. Item 10 and 11: Wheel Bearing Oil Seal and Axle Shaft Bearing Removal Note 1. CAUTION: Never remove the wheel bearing oil seal by itself. Always remove the wheel bearing oil seal and the rear wheel bearing at the same time. For the 8.8 inch rear axle, use the special tools to remove the rear wheel bearing and wheel bearing oil seal. 2. CAUTION: Never remove the wheel bearing oil seal by itself. Always remove the wheel bearing oil seal and the rear wheel bearing at the same time. For the 9.75 inch and the 10.25 inch rear axles, use the special tools to remove the rear wheel bearing and wheel bearing oil seal. Item 11: Axle Shaft Bearing Installation Note 1. For the 8.8 inch and the 9.75 inch rear axles, use the special tools to install the rear axle wheel bearing. 2. For the 10.25 inch rear axle, use the special tools shown to install the rear axle wheel bearing. Item 10: Wheel Bearing Oil Seal Installation Note 1. Use the special tools shown to install the rear wheel bearing oil seal. Item 8: U-washer Installation Note 1. CAUTION: Do not damage the rubber O-rings in the U-washer grooves. Install the U-washers. 1. Position the two U-washers on the button end of the axle shafts. 2. Pull the axle shafts outward.

Related entry:

2004 ford explorer rear differential diagram, tourch on rear wheel bearing on a 2010 chevy impala, balance shaft seal for 2004 honda acccord 4 cylinder schematic, 2006 suzuki forenza front wheel drive axle diagram, 2004 expedition right axle tube seals, 2008 chevy silverado cv axle nut size, 2004 ford escape rear gears, how to remove rear axle shaft of mitsubishi strada triton, 2007 acadia rear blower removal, 2004 trailblazer front axle seals exploted view,

1997 Oldsmobile Bravada Axle Shaft Assembly: Service and Repair Drive Axle Installation FRONT DRIVE AXLE

0

Filed Under (Oldsmobile) by admin on 18-08-2010

download
INSTALL OR CONNECT It is essential that the differential carrier, axle seals are not lubricated or damaged during this process. Prior to drive axle installation, cover the shock mounting bracket, lower control arm bail stud, and all other sharp edges with a shop towel so as not to damage the boot. 1. Axle shaft to differential carrier. With both hands on the tripot housing, align the splines on the shaft with the differential carrier. Then center the drive axle into the differential carrier seal and firmly push the shaft straight into the differential carrier until the snap ring seats into place. NOTICE: Be careful that the safety stand does not damage or bend any components it may contact. 2. Raise the safety stand to support the weight of the lower control arm. Important: It will be necessary to slightly start the knuckle onto the drive axle while simultaneously guiding the lower ball stud to its proper 1997 Oldsmobile Truck Bravada V6-4.3L VIN W location on the steering knuckle. 3. Assemble the lower ball joint. 4. Lower shock mount. 5. Upper ball joint. 6. Drive axle washer and nut. 7. Drive axle nut. – Tighten bolts to 140 Nm (103 ft. lbs.). 8. 9. 10. 11. 12. ABS Bracket located on the top of the upper control arm ball joint. Brackets from upper control arm holding both the ABS wire and brake hose. Caliper and rotor. Tires and wheel. Remove safety stands.

Related entry:

2007 mazda 3 front axle nut torque, f250 front axel diagram for 4x4 2002, how to replace inner axle bearing in a dodge stratus se, repair 2003 pontiac bonneville stud bolts spindle front right side, 4 x 4 front axle, torque on axle nut 06 ford escape, diagram for a 2000 chevy s10 4x4 front differential, fuse box for 1997 oldsmobile 88, front drive axle battery for 2001 chevy tracker diagram, 2000 mercury cougar axle nut threads and sizes chart,

2004 Nissan Murano Malfunction Indicator Light (MIL) is ON Bank 1 catalytic converter code P0420

0

Filed Under (Nissan) by admin on 21-12-2010

download
Vehicle Application: Customer Concern: Tests/Procedures: Potential Causes: Tech Tips: 2004 Nissan Murano 3.5L, USA/Canada Malfunction Indicator Light (MIL) is ON. Bank 1 catalytic converter code P0420. 1. Check scan data for fuel trims to see if the system is in proper fuel control – look for 0% plus or minus 10% in generic or 90 – 110 % alpha in manufacture specific. 2. Verify there are no exhaust leaks. 3. Drive the vehicle and check the bank 1 rear O2 sensor activity on the scan tool or with a voltmeter to see if the bank 1 rear O2 sensor is cross counting like a typical front O2 sensor would. Catalytic Converter If in manufacture specific with the scan tool, Nissan displays fuel trims in alpha. 100% alpha is the same as 0% fuel trim. This vehicle has front air fuel ratio sensors – not O2 sensors. Bank 1 is the firewall bank. Bank 2 is the radiator bank. Before the catalytic converter lights off, the rear O2 sensor voltage is usually down around 0.2 – 0.4 volts or so but when the catalytic converter lights off, it uses up a lot of the oxygen so the rear O2 sensor voltage will typically reads around 0.6 – 0.7 volts and have some movement but not a lot of movement and should not cross count above and below 0.5 volts. The catalytic converter is covered under the 8 year 80,000 mile federal emissions warranty. 2004 Nissan Quest 3.5L, USA/Canada

Related entry:

2007 honda pilot catalytic converter bank 1, where is bank 2 catalytic converter honda pilot, 04 mdx bank2, where is bank 2 catalytic converter located on 2005 honda pilot, what does the rear catalytic converter look like on the 2004 nissan murano, removing the converter on a 2002 pathfinder, procedure for catalytic converter replacement on 2003 nissan frontier, p0868 pressure control solenoid valve B location 2009 nissan murano, MURANO IVT SYSTEM, how to change CONTROL VALVE SOLENOID nissan murano,

1996 Pontiac Bonneville Axle Shaft Assembly: Service and Repair FRONT DRIVE AXLE

0

Filed Under (Pontiac) by admin on 11-08-2010

download
1. Raise and support vehicle, then remove tire and wheel assembly. 2. Install a brass drift or a screwdriver to prevent the rotor from turning, Fig. 7 . 3. Remove axle nut and washer. 4. Remove stabilizer shaft or link from control arm. 5. Remove nut from ball joint, then separate ball joint from steering knuckle using separator tool No. J-36226, or equivalent. 6. Remove drive axle from hub and bearing assembly using front hub spindle remover tool No. J-28733-A, or equivalent, Fig. 8 . 7. Remove drive axle from transaxle using axle shaft remover puller tool Nos. J-33008, J-29794 and slide hammer tool No. J-2619-01, or equivalents, if necessary, Fig. 9 . INSTALLATION 1. Install drive axle into the transaxle using seal protector J-37292-B, or equivalent 2. Seat snap ring by placing a screwdriver into the groove on the joint housing and tapping until seated, Fig. 9 . 3. Grasp the inner housing and pull outward. If the snap ring is properly seated, the axle will remain in place. 4. Install drive axle into hub and bearing assembly. 5. Install lower ball joint to steering knuckle and tighten to specifications. 6. Install stabilizer shaft or link to control arm, tighten to specifications. 7. Insert a screwdriver or drift into caliper and rotor to prevent rotor from turning, Fig. 7 . 8. Install new hub nut and washer, tighten to specification. 9. Install tire and wheel assembly, then lower vehicle

Related entry:

1996 bonneville cv joint and strut assembly, 1996 nissan axle torque, Ford 7/8 clamping wheel nut LN105, torque spec for 2001 bonneville axle nut, torque specs for 2001 bonneville sle front hubs,

2005 Chevy Suburban Front Axle Will Not Disengage

0

Filed Under (Chevrolet) by admin on 30-10-2010

download
Front Axle Will Not Disengage Circuit Description The front axle control circuit consists of an electric motor actuator which engages and disengages the front axle. The front axle actuator motor consists of a permanent magnetic motor, a worm gear controlled plunger, a front axle switch and an electronic control circuit all within the actuator assembly. The front axle actuator consists of the following circuits: The front axle control circuit, which is also connected to the transfer case shift control module The front axle switch circuit, which is also connected to the transfer case shift control module A battery feed circuit A ground circuit When a shift to AUTO 4WD, 4HI or 4LO is requested, the transfer case shift control module engages the front axle by grounding the front axle control circuit through a current limiting driver. Diagnostic Aids A mechanical condition inside the front axle could prevent the shift fork from moving causing the motor to be stuck in one position. Refer to Symptoms – Front Drive Axle See: Differential Assembly\Testing and Inspection\Symptom Related Diagnostic Procedures\Diagnosis By Symptom – Front Drive Axle\- Symptoms – Front Drive Axle

Related entry:

2007 avalanche front differential fill hole, labor time repair 2010 tundra tranmission actuator, 2007 chevy suburban differential plug, how to test a front actuator chevy colorado, what torque oil oil bolt hands on suburban chicago,