nissan twincam 16 valve engine


You are searching repair manual in PDF format about nissan twincam 16 valve engine use another keyword for search another post or files



  nissan twincam 16 valve engine Direct Download speed 5787 Kb/s

  nissan twincam 16 valve engine Full Version speed 6767 Kb/s




2010-2011 Cadillac Escalade Active Fuel Management (AFM) Engine, Valve Lifter Tick Noise at Start Up When Engine Has Been Off for 2 Hours or More

0

Filed Under (Cadillac) by admin on 25-01-2011

download
Condition Some customers may comment on an engine valve lifter tick noise that occurs after the engine has been shut off for at least two hours. The tick noise may last from two seconds to ten minutes. Cause This condition may be caused by any of the following: • Aerated oil in the valve lifter body, resulting in the valve lifter being unable to purge the air quickly. • A low engine oil level or incorrect oil viscosity. • Dirty or contaminated oil. • A low internal valve lifter oil reservoir level. • Debris in the valve lifter. • A high valve lifter leak down rate. Correction If the SI diagnostics do not isolate the cause of this valve lifter tick noise and normal oil pressure is noted during the concern, perform the following steps: 1. Inspect the engine oil condition and level. Refer to Owner Manual > Service and Appearance Care > Checking Things Under the Hood > Description and Operation > Engine Oil in SI. ? If the engine oil is more than one quart low, an incorrect oil viscosity is being used or if poor quality/contamination is observed, change the oil and filter. Note: Allow at least a two hour soak time between engine OFF and start up when evaluating the tick noise. 2. Start the engine and evaluate the valve lifter tick noise. ? If the valve lifter tick noise is still present, replace all 16 valve lifters. Refer to Valve Lifter Replacement in SI.

Related entry:

clear prostar engine codes, engine harnesskia carens, nissan twin cam 16 valve engine, vacuum diagram dohc nissan 16 valve, porque suenan los lifters de impala 2001 motor 3800, VAPOR MANAGEMENT VALVE 2005 F150, vapor management valve 2011 F150, what is tdc on the chevy northstar 32 valve engine, 2005 f150 5 4 location vapor management valve, nissan ka20 16 valve motor,

2006 Mazda5 BODY VIBRATION AT CRUISE SPEED

0

Filed Under (Mazda) by admin on 16-06-2011

download
DESCRIPTION Some vehicles may experience a body vibration when driving approximately 55mph. This symptom is due to the characteristics of the No. 3 & No. 4 engine mounts. Modified No. 3 & No. 4 engine mounts have been established for service only. Customers having this concern should have their vehicle repaired using the following repair procedure. REPAIR PROCEDURE IMPORTANT NOTE: • This repair should only be performed if all tires and rims are confirmed to be in balance and all suspension components are in proper working condition. • Notify customers that use of the modified mounts will reduce vibration at cruising speed but may increase vibration at idle. NOTE: Because idle vibration may increase, it is highly recommended to continue using mass production mounts for all other service concerns. 1. Verify concern. 2. Replace the No. 3 & 4 engine mounts with service parts according to the appropriate Workshop Manual section 01-10 ENGINE REMOVAL/INSTALLATION. 3. Center the new engine mounts as outlined in ENGINE MOUNT CENTERING PROCEDURE. 4. Verify repair. ENGINE MOUNT CENTERING PROCEDURE No. 1, No. 3 and No. 4 Engine Mount Adjustment 1. Warm up the engine. 2. Raise and support vehicle on a hoist. 3. Remove engine under cover. 4. Lower the vehicle until the front tires lightly touch the ground. 5. Secure the engine and transaxle using an engine jack and attachment as instructed in No.3 Engine Mount And No.4 Engine Mount Rubber Installation Note in appropriate Workshop Manual, section 01-10 MECHANICAL. 6. Remove two bolts from No. 3 engine mount bracket. REMOVE THE BOLTS 7. Lift engine using jack until No.3 engine mount is lifted slightly from vehicle body. NOTE: • Do not raise engine too much or A/C pipe damage may occur. 8. Move the engine mount rubber or engine until installation hole on the vehicle body aligns with hole in the engine mount bracket. ENGINE MOUNT BRACKET 1532c SHOWN BEFORE ALIGNING THE HOLES SHOWN AFTER ALIGNING THE HOLES 9. Lower the jack and tighten bolts on No. 3 engine mount bracket. Tightening torque: 55.0-77.3 ft-lbf (74.5-04.9 N.m) NOTE: 10. With engine supported as described in STEP 5, remove four (4) nuts and two (2) bolts from No. 4 engine mount top plate. Remove top plate. NOTE: 11. Lift engine again using jack until No.4 engine mount is lifted slightly from vehicle body. NOTE: 12. With top plate of No. 4 engine mount removed, move engine mount bottom plate or engine until all four (4) installation studs on the vehicle align with the engine mount holes. • Do not allow the engine mount bracket to be misaligned. • To access the mount, remove battery box. • Do not raise engine too much or A/C pipe damage may occur. ALIGN THE 4 STUDS IN THE PLATE HOLES 13. Place top plate back on and tighten No. 4 engine mount bracket nuts and bolts to torque indicated. Tightening torque: A.32.5-45.0 ft-lbf (44.0-61.0 N.m) B.61.1-86.7 in-lbf (6.9-9.8 N.m) TIGHTEN BOLTS IN SEQUENCE SHOWN 1532e 14. Lift engine again using jack and loosen the two bolts on the No. 1 engine mount rubber until slightly loose on the No. 1 engine mount rubber.

Related entry:

nissan ka20 engine manual free, 4 0 ford sohc headgasket replace engine out of vehicle dont remove timing covers, ford ka engine layout, 2000 chevy venture engine removal, 1997 ford 4 0 engine diagram, replace radiator mercedes mb140d 2002, 1999 audi a4 2 8 engine diagram, audi a4 engine football holes diagram, s4ph manual, how to fix 1997 ford fiesta speedometer rocam engine,

1992 Suzuki Swift VALVE CLEARANCE ADJUSTMENT

0

Filed Under (Suzuki) by admin on 26-05-2011

download
NOTE: Samurai & Sidekick 1) Remove rocker cover. Rotate crankshaft until zero degree (TDC) timing mark of timing belt cover is in line with timing mark on crankshaft pulley. 2) Cylinder No. 1 should be at TDC on compression stroke. Remove distributor cap, and ensure rotor is pointed upward at distributor hold-down bolt and to No. 1 terminal of distributor cap. If not as described, rotate crankshaft 360 degrees. 3) Measure valve clearance between adjustment screw and valve stem using thickness gauge. Check intake valve clearance of cylinders No. 1 and 2 and exhaust valve clearance of cylinders No. 1 and 3. 4) Turn crankshaft one complete revolution (360 degrees). Check intake valve clearance of cylinders No. 3 and 4 and exhaust valve clearance of cylinders No. 2 and 4. Ensure clearance is within specification. See VALVE CLEARANCE SPECIFICATIONS table. 5) If clearance adjustment is necessary, loosen lock nut and turn adjusting screw. After adjusting clearance, tighten adjusting Swift DOHC uses hydraulic lifters. Adjustment is not required. screw lock nut to 11-14 ft. lbs. (15-19 N.m) on Samurai or 90-108 INCH lbs. (10-13 N.m) on Sidekick. On all models, recheck clearance. VALVE CLEARANCE SPECIFICATIONS TABLE ¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡ Application SOHC Engines Samurai, Sidekick 8-Valve TBI & Swift (1) Engine Cold Exhaust ……………………. .006-.008 (.15-.20) Intake …………………….. .005-.007 (.13-.17) Engine Hot Exhaust ……………………. .010-.012 (.25-.30) Intake …………………….. .009-.011 (.23-.27) Sidekick 16-Valve PFI Engine Cold Exhaust & Intake ………….. .0031-.0047 (.08-.12) Engine Hot Exhaust & Intake ………….. .0047-.0063 (.12-.16) DOHC Engine Swift (1) …………………………………. (2) (1) – Swift is available with 1.3L DOHC and SOHC engines. (2) – Hydraulic valve lash adjusters are used. Adjustment is not required. ¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡ Swift SOHC 1) Remove rocker cover. Remove right side inner fender apron extension to enable timing marks to be seen. Align crankshaft pulley timing mark with TDC mark on timing belt cover. 2) Remove distributor cap. Ensure rotor is pointing upward toward distributor hold-down bolt and to No. 1 terminal of distributor cap. If not as described, rotate crankshaft 360 degrees. 3) Measure valve clearance between adjustment screw and valve stem using thickness gauge. Check intake valve clearance of cylinders No. 1 and 2 and exhaust valve clearance of cylinders No. 1 and 3. Turn crankshaft one complete revolution (360 degrees). Check intake valve clearance of cylinders No. 3 and 4 and exhaust valve clearance of cylinders No. 2 and 4. 4) Ensure clearance is within specification. See VALVE CLEARANCE SPECIFICATIONS table. If clearance adjustment is necessary, loosen lock nut and turn adjusting screw. Hold adjusting screw while tightening lock nut to 11-14 ft. lbs. (15-19 N.m). Recheck clearance. In. (mm)

Related entry:

vavle lash adjustment procedure for a 1 8 l 1997 mirage, 2003 altima 2 5 valve clearances, 2003 honda accord 4cyl piston tighten, valve adjustment on 2000 ford courier 2 5 turbo, how to adjust valve clearance on a 4g13, zetec valve clearance, 2004 ford courier valve adjustment, purge sensor location 2008 suzuki xl7, 2003 miata vvt 10 degrees out, Ford Econovan 1994 Workshop Manual,

2000-2001 Nissan Maxima Engine rough running Engine surging Low engine power

0

Filed Under (Nissan) by admin on 21-12-2010

download
SERVICE INFORMATION If an applied vehicle has DTC P0100 stored and possibly exhibits, • • • Engine rough running Engine surging Low engine power the cause may be an airflow sensor that has been damaged by air-ingested dust/dirt. To resolve this incident, if it should occur, follow the steps outlined in the Service Procedure on page 2. Service Procedure Summary: • Remove dust/dirt/debris from inside the air cleaner housing. This will help prevent another incident. • A new genuine Nissan air filter element must be used for all warranty claims, and any other claim for which Nissan pays. A new genuine Nissan air filter element is designed to be compatible with the Nissan air flow meter and has proven to provide adequate dust protection to help prevent these incidents. It is strongly recommended that incident customers continue using Nissan genuine air filters for assured protection when replacing according to the routine maintenance schedule. See parts information for the air filter part number (P/N). • Install a new complete airflow meter assembly. See Parts Information for the part number (P/N). • Reprogram the ECM with special new data that is matched to the different output characteristics of the new airflow meter.

Related entry:

1997 nissan maxima surge, 96 MAXIMA ENGINE SURGE, peugeot 308 runs rough at low speed,

2GR-FE Engine Ticking Noise and/or MIL “ON” P0014, P0015, P0024, P0025, P0017, or P0018

0

Filed Under (Toyota) by admin on 20-05-2011

download
Introduction IMPORTANT It is mandatory that the VVT-i gear actuator bolts, actuator center section alignment, and actuator body be inspected BEFORE performing this TSB. If no concerns are noted with these parts, this TSB does NOT apply. Some 2005 – 2009 model year vehicles with 2GR-FE engines may exhibit a ticking/clicking type noise from the cylinder head cover area which may be accompanied by a MIL “ON” and one or more VVT-i related Diagnostic Trouble Codes (DTCs). Please use the following repair procedure to address customer concerns. Inspection Procedure 1. Start the engine and listen for any ticking/clicking type noises coming from the VVT-i gear area of the engine. NOTE This condition may or may not be accompanied by one or more of the following DTCs stored in the Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM): • P0014: Camshaft Position “B” – Timing Advanced or System Performance (Bank 1) • P0015: Camshaft Position “B” Timing Over Retarded (Bank 1) • P0017: Crankshaft Position Camshaft Position Correlation (Bank 1 Sensor B) • P0018: Crankshaft Position Camshaft Position Correlation (Bank 2 Sensor A) • P0024: Camshaft Position “B” – Timing Over-Advanced or System Performance (Bank 2) • P0025: Camshaft Position “B” – Timing Over-Retarded (Bank 2) 2. Remove the cylinder head cover and inspect the exhaust VVT-i gear assembly on the affected cylinder bank. NOTE If NO concerns are found with the VVT-i gear actuator bolts, the actuator center section alignment, or actuator body, this TSB does NOT apply. Refer to Repair Manual procedures for further diagnosis. Repair Procedure 1. If any concerns are noted with the exhaust VVT-i gear bolts or actuator follow the four steps below: A. Replace the camshaft housing sub-assembly, exhaust camshaft, and exhaust VVT-i gear assembly on the affected bank. B. Inspect the intake VVT-i gear assembly and bolts on the affected bank. Replace the intake VVT-i gear assembly if necessary. C. Inspect the opposite bank exhaust VVT-i gear actuator and bolts. If any concerns are noted replace the opposite bank camshaft housing sub-assembly, exhaust camshaft, and exhaust VVT-i gear assembly. D. Inspect the opposite bank intake gear actuator assembly and bolts. Replace the intake VVT-i gear assembly if necessary. For complete disassembly procedures refer to the Technical Information System (TIS), applicable model and model year Repair Manual: • 2005 Avalon: Engine/Hybrid System – Engine Mechanical – “Engine Mechanical: Camshaft (LH Bank) / (RH Bank) (2GR-FE): Replacement” • 2006 / 2007 / 2008 / 2009 Avalon: Engine/Hybrid System – Engine Mechanical – “2GR-FE Engine Mechanical: Engine Unit: Disassembly” • 2007 / 2008 / 2009 Camry: Engine/Hybrid System – Engine Mechanical – “2GR-FE Engine Mechanical: Engine Unit: Disassembly” • 2008 / 2009 Highlander: Engine/Hybrid System – Engine Mechanical – “2GR-FE Engine Mechanical: Engine Unit: Disassembly” • 2006 / 2007 / 2008 / 2009 RAV4: Engine/Hybrid System – Engine Mechanical – “2GR-FE Engine Mechanical: Engine Unit: Disassembly”

Related entry:

07 mazda cx 7 vvt adjust, engine timing marks for isuzu 4HFI that have no timing belt, camshaft positioning diagram for Mazda bt-50 wlat engine, 2010 cadillac srx 3 0 bank one location, volvo vvt, sonata p0014, rav4 p1349, mazda mx5 vvt replacement, how hard is it to change am oil pan on a 2006 malibu with a 2 2 four cylinder, 2002 miata vvt acuator,