octavia egr valve vacuum pipe removal


You are searching repair manual in PDF format about octavia egr valve vacuum pipe removal use another keyword for search another post or files



  octavia egr valve vacuum pipe removal Direct Download speed 5787 Kb/s

  octavia egr valve vacuum pipe removal Full Version speed 6767 Kb/s




2004 Jeep Grand Cherokee Limited DIAGNOSIS AND TESTING – VACUUM RESERVOIR

0

Filed Under (Jeep) by admin on 18-11-2010

download
1. Disconnect vacuum hose at speed control servo and install a vacuum gauge into the disconnected hose. 2. Start engine and observe gauge at idle. Vacuum gauge should read at least ten inches of mercury. 3. If vacuum is less than ten inches of mercury, determine source of leak. Check vacuum line to engine for leaks. Also check actual engine intake manifold vacuum. If manifold vacuum does not meet this requirement, check for poor engine performance and repair as necessary. 4. If vacuum line to engine is not leaking, check for leak at vacuum reservoir. To locate and gain access to reservoir, refer to Vacuum Reservoir REMOVAL /INSTALLATION . Disconnect vacuum line at reservoir and connect a hand-operated vacuum pump to reservoir fitting. Apply vacuum. Reservoir vacuum should not bleed off. If vacuum is being lost, replace reservoir. 5. Verify operation of one-way check valve and check it for leaks. a. Locate one-way check valve. The valve is located in vacuum line between vacuum reservoir and engine vacuum source. Disconnect vacuum hoses (lines) at each end of valve. b. Connect a hand-operated vacuum pump to reservoir end of check valve. Apply vacuum. Vacuum should not bleed off. If vacuum is being lost, replace one-way check valve. c. Connect a hand-operated vacuum pump to vacuum source end of check valve. Apply vacuum. Vacuum should flow through valve. If vacuum is not flowing, replace one-way check valve. Seal the fitting at opposite end of valve with a finger and apply vacuum. If vacuum will not hold, diaphragm within check valve has ruptured. Replace valve.

Related entry:

yhs-sgm_fb, vacum line diagram for 91 honda accord, Free Engine Vacuum Diagrams, 6N0201277, repair durango ac/heat control vac lines, vacuum hose disconnected on highlander, vaccum chamber 1992 chev van ebay, 1978 Corvette Vacuum Hose Diagram, ford taurus 2001 engine vacuum hoses on intake, 1998 dakota 2 5 liter vacuum line routing,

1994 Ford Mustang Dual Converter and Pipe 5.0L Engine Removal Installation

0

Filed Under (Ford) by admin on 07-02-2011

download
5.0L Engine Removal 1. Raise vehicle. Refer to Section 00-02. 2. Disconnect air inlet tube (5F235) from the dual converter and pipe. 3. Remove dual converter and pipe to exhaust manifold retaining nuts. 4. Remove muffler inlet flange to dual converter and pipe outlet flange retaining nuts. 5. Support dual converter and pipe with a suitable jackstand and remove exhaust converter frame bracket to dual converter and pipe retaining nuts. 6. Remove dual converter and pipe from vehicle. 7. Replace any damaged parts. Installation 1. Loosely install dual converter and pipe and support with a suitable jackstand. 2. Install dual converter and pipe onto exhaust converter frame bracket (5E269) and install retaining nuts. Tighten retaining nuts to 14.8-20.2 Nm (11-15 lb-ft). 3. Position dual converter and pipe to exhaust manifold studs and install retaining nuts. Do not tighten nuts. 4. Position muffler inlet flanges to dual converter and pipe outlet flanges and install retaining nuts. Do not tighten nuts. Remove jackstand. 5. Align exhaust system to specification, refer to appropriate illustration. 6. With exhaust system aligned: a. Tighten dual converter and pipe-to-exhaust manifold nuts to 34-46 Nm (25-34 lb-ft). b. Tighten muffler inlet flanges-to-dual converter and pipe outlet flanges retaining nuts to 29.7-40.3 Nm (22-30 lb-ft). 7. Attach air inlet tube to dual converter and pipe. Tighten clamp securely. 8. Check system for leaks and lower vehicle. 3.8L Engine Removal 1. Raise vehicle. Refer to Section 00-02. 2. Remove dual converter and pipe-to-exhaust manifold retaining nuts. 3. Remove dual converter and pipe outlet flange to muffler inlet flange retaining nuts. 4. Support dual converter and pipe with a suitable jackstand and remove exhaust converter frame bracket to dual converter Y pipe retaining nuts. 5. Remove dual converter and pipe from vehicle. 6. Replace any damaged parts. Installation 1. Loosely install dual converter and pipe and support with a suitable jackstand. 2. Install dual converter and pipe onto exhaust converter frame bracket and install retaining nuts. Tighten retaining nuts to 14.8-20.2 Nm (11-15 lb-ft). 3. Position dual converter and pipe to exhaust manifold studs and install retaining nuts. Do not tighten retaining nuts. 4. Position muffler inlet flange to dual converter and pipe outlet flange. Loosely install retaining nuts. 5. Align exhaust system to proper clearance specifications, as shown in the appropriate illustration. 6. With exhaust system aligned: a. Tighten dual converter and pipe to exhaust manifold nuts to 34-46 Nm (25-34 lb-ft). b. Tighten muffler inlet flange to dual converter and pipe flange retaining nuts to 29.7-40.3 Nm (22-30 lb-ft). 7. Check exhaust system for leaks.

Related entry:

1996 toyota camry V6 1MZ-FE exhaust flex pipe, exhaust pipe repair section with O2 bung for 1998 Avalon, flex pipe for 1998 ford contour, Ford Escape Flex Pipe Repair, how many catalytic converters on a 2000 avalon, how to install a flex pipe manifold adaptor on a 1998 toyota avalon, how to install front pipe on a 2008 ford escape, how to replace exhaust pipe on a ford contour, how to replace flex pipe on 99 ford contour, installation of down flex pipe on audi a4,

1996 Ford Taurus valve body Removal and Installation

0

Filed Under (Ford) by admin on 16-10-2010

download
REMOVAL NOTE: The oil pump and valve body are removed as an assembly. 1. Disconnect battery ground cable, then remove battery, battery tray, and remote air cleaner. 2. Position supply hoses, vacuum hoses, and wiring away from pump and valve body cover. 3. Remove shift lever. 4. On models equipped with Anti-lock Brake System (ABS) , remove splash shield cover, then disconnect brake reservoir hose and cap to prevent contamination. 5. On all models, remove EGR bracket attaching bolts, then install lifting eye. 6. Remove throttle body bracket attaching bolt, install lifting eye, then using suitable equipment support engine. 7. Remove lefthand transaxle mount. 8. Remove transaxle side pan upper attaching bolts. 9. Raise and support vehicle. 10. Remove lefthand front wheel and tire assembly. 11. Remove inner fender cover and position aside, then disconnect ride height sensor. 12. Remove rear transaxle mount attaching bolt. 13. Loosen but do not remove two lefthand subframe attaching bolts. 14. Remove two engine support mount attaching bolts. 15. Remove four lefthand engine support attaching bolts, then remove the engine support. 16. Position suitable drain pan, then remove remaining transaxle side pan attaching bolts and remove pan. 17. Using suitable screwdriver, place manual shift shaft in Park position. 18. Disconnect upper bulkhead electrical connector wiring retainer clip from valve body. 19. Disconnect electrical connectors. Oil Pump And Valve Body Bolt Removal 20. Remove valve body attaching bolts, then disengage linkage and remove valve body. NOTE: Do not remove oil pump cover attaching bolts. INSTALLATION 1. Install new pump and valve body to chain cover gasket. 2. Slide pump and valve body onto pump shaft. 3. Rotate pump and valve body assembly toward dash panel, then engage manual valve link with manual valve. 4. Slightly rotate pump and valve body assembly to engage oil pump shaft splines with oil pump rotor splines. Valve body should slide flush with chain cover. A suitable 7/8 inch deep well socket on crankshaft pulley may be required for complete engagement. 5. On models less anti-skid, if engagement is not as indicated in step 4, proceed as follows: a. Remove manual valve from valve body. b. Rotate assembly to allow full engagement, up to 360° . c. After full engagement, return assembly to installed position, then install manual valve.

Related entry:

REPAIR INSTRUCTIONS VALVE BODY SOLENOID 2005 AUDI A4, 4l60e valve body bolt location, 2006 nissan xterra transmission valve body, International Body Controller Codes, manual valve installation for 4r55e tranny, lincoln ls valve body removal, ax4n valve body manual, ford ax4n valve body diagram, diagram u140 transmission vavle body, manual valve installation for 4r55e,

2005 Chevrolet Malibu Vacuum Brake Booster Check Valve and/or Hose Replacement Removal Procedure

0

Filed Under (Chevrolet) by admin on 19-10-2010

download
1. Disconnect the brake booster vacuum check valve (1) from the brake booster. 2. If the vacuum check valve (1) needs to be separated from the vacuum hose (3), release and reposition the clamp (2) on the vacuum hose (3) and remove the check valve (1) from the hose (3). 3. If replacing the vacuum check valve (1), remove the grommet (4) from the brake booster and discard the grommet. 4. If removing the vacuum hose (2), take note of the vacuum hose routing then disconnect from the engine intake manifold connection (3) by releasing tension on the vacuum hose clamp (1) and sliding the vacuum hose (2) off the intake manifold connection (3). Installation Procedure Important: A small amount of denatured alcohol can be used as an assembly aid when installing the vacuum check valve and/or grommet. Do NOT use soap. 1. If the vacuum hose (2) was removed, install the vacuum hose into position on the vehicle as noted prior to removal, then connect the vacuum hose (2) to the engine intake manifold connection (3) and secure with the vacuum hose clamp (1). 2. If the vacuum check valve (1) is being replaced, install a NEW grommet (4) to the brake booster. 3. If the vacuum check valve (1) was separated from the vacuum hose (3), install the check valve (1) to the vacuum hose (3). Install and secure the clamp (2) into position on the hose (3). 4. Connect the brake booster vacuum check valve (1) to the brake booster.

Related entry:

2005 caravan cruise control hose routing diagram, 1999 Dodge Intrepid vacuum hose manual, 2000 chevy malibu vac line routing, 2001 explorer sport trac air intake hose leak, 90 toyota camry 2 0 intake manifold hose diagrams, 98 mercury mystique vacuum lines, 2000 s10 2 2 vaccuum lines sale, loation of vacuum hose on 2005 pgmc denali, 2001 chevy malibu 3 1 vacuum lines to transmission, 2002 chrysler t & c vacuum lines diagram,

2001 Chevrolet Cavalier Idle Air Control Motor (IAC): Service and Repair REMOVAL PROCEDURE

0

Filed Under (Chevrolet) by admin on 16-09-2010

download
1. Remove the idle air control (IAC) valve connector. 2. Remove the IAC valve attaching screws (1). NOTE: If the IAC valve has been in service: DO NOT push or pull on the IAC valve pintle. The force required to move the pintle may damage the threads on the worm drive. Also, DO NOT soak the IAC valve in any liquid cleaner or solvent, as damage may result. 3. Remove the IAC valve assembly (2). ^ Clean the IAC valve O-ring sealing surface, the pintle valve seat, and the air passage. ^ The IAC valve may be cleaned. Use a shop towel or parts cleaning brush to remove any heavy deposits. ^ Any shiny spots on the pintle or seat are normal and do not indicate misalignment or a bent pintle shaft. ^ If the air passage have heavy deposits, remove the throttle body for a complete cleaning. ^ Inspect the IAC valve O-ring for cuts, cracks, or distortion. Replace the O-rings if necessary. ^ When installing a new IAC valve, be sure to replace the valve with an identical part. The IAC valve pintle shape and diameter are designed for a specific application. MEASUREMENT PROCEDURE This procedure is only for installing a new IAC valve. IMPORTANT: If installing a new IAC valve, replace the IAC valve with an identical part. The IAC valve pintle shape and diameter are designed for the specific application. Measure the distance between tip of the IAC valve pintle and the mounting flange. If the distance is more than 28 mm (1.1 in), use finger pressure to slowly retract the pintle. The force required to retract the pintle of a new valve will not cause damage to the valve. INSTALLATION PROCEDURE

Related entry:

idle adjustment screw 1994 pontiac grand prix, how to chech fuses for iac valve on a 2001 infinity i30, accidentally cut bolts after atf flush on rx300, mercruiser IAC control valve replacement, mercruiser iac replacement, 1999 z24 symptoms of bad iac, location of icv on 2001 4 3 v6 vortec, mercruiser 5 0 iac removal, verona iac, mercruiser 5 0 iac valce diagram,