pajero 4d56 injection pump adjustment


You are searching repair manual in PDF format about pajero 4d56 injection pump adjustment use another keyword for search another post or files



  pajero 4d56 injection pump adjustment Direct Download speed 5787 Kb/s

  pajero 4d56 injection pump adjustment Full Version speed 6767 Kb/s




1995 Mercury Villager Water Pump Removal Installation

0

Filed Under (Mercury) by admin on 24-02-2011

download
1. Drain the cooling system. Refer to Section 03-03 for the procedure. 2. Disconnect the battery ground cable (14301) . 3. Remove the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the removal procedures. 4. Raise and support the vehicle. 5. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley (8509) while removing the four water pump pulley bolts. 6. Remove the water pump pulley from the water pump (8501) . 7. Remove the crankshaft pulley (6312) . Refer to the procedure in this section 8. Remove the five lower engine front cover bolts and the lower engine front cover (6019) . 9. NOTE: Make a note of the location of the one water pump stud/bolt for ease of installation. Remove the six water pump bolts. 10. Remove the water pump . Installation 1. NOTE: Ensure the mating surfaces between the water pump and the cylinder block (6010) are cleaned of any sealant material. Install a continuous 2.0-3.0mm (0.079-0.118 inch) wide bead of Gasket Maker E2AZ-19562-B or equivalent meeting Ford specification WSK-M2G348-A5, on the water pump and position the water pump on the cylinder block . 2. NOTE: Refer to the note made during removal for the location of the stud/bolt. Install the six water pump bolts. Tighten the water pump bolts to 16-21 Nm (12-15 lb-ft). 3. Position the water pump pulley on the water pump and install the four water pump pulley bolts. 4. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley , and tighten the four water pump pulley bolts to 16-21 Nm (12-15 lb-ft). 5. Install the lower engine front cover and the five lower engine front cover bolts. Tighten the five lower engine front cover bolts to 3-5 Nm (27-44 lb-in). 6. Install the crankshaft pulley . Refer to the procedure in this section. 7. Lower the vehicle. 8. Install and adjust the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the installation and adjustment procedures. 9. Connect the battery ground cable . 10. Fill the cooling system. Refer to Section 03-03 for the procedure. 11. Start the engine (6007) and check for leaks.

Related entry:

91 chrysler new yorker brake bleed procedure, repair guide 2006 jeep commander power steering pump, sidekick waterpump removal, strap wrench D85L-6000A,

Removing and installing injection pump

0

Filed Under (repair and maintenance tips) by admin on 25-06-2010

download
Rotate crankshaft in direction of rotation to 14o + 0.5o (arrow) after ignition TDC of cylinder 1 Unscrew central securing bolt (40/3) Remove chain tensioner Unplug socket of injection pump (Y23/1) at plug connection Unbolt engine wiring harness (1) at oil filter housing Unplug connector at electronic IFI shutoff (Y1/1) Detach fuel lines (arrows) at the injection pump Unscrew bolt (10/3) Unscrew bolts (10/1) Slacken bolt (30/1) of start of delivery setting device Remove injection pump (10) Replace O-rings (10/4) Install in the reverse order Inspect start of delivery Set start of delivery Injection pump, unit pump, high pressure pump Designation Central bolt for attaching injection pump Bolt of injection pump bracket at rear to engine block Bolt of injection pump front M8 Screw plug to governor housing

Related entry:

mitsubishi 4m50 injection pump installation, yd25 any filter in pump,

1998 Ford Mustang Water Pump Removal Installation

0

Filed Under (Ford) by admin on 03-02-2011

download
1. Drain engine cooling system. Refer to Section 03-03. 2. Remove upper radiator sight shield (8C291). 3. Disconnect radiator overflow hose (8075) from radiator (8005). Remove bolts retaining coolant recovery reservoir (8A080) and bracket to radiator support. Disconnect coolant recovery reservoir from lower locator and remove coolant recovery reservoir. 4. Remove cooling fan motor, fan blade (8600) and fan shroud (8146) assembly as described in Section 03-03. 5. Rotate drive belt tensioner (6B209) . Remove drive belt (8620) . Refer to Section 03-05. 6. Remove retaining bolts and water pump pulley (8509) . 7. Remove power steering pump pulley (3A733) and remove water pump-to-power steering pump brace. 8. Remove bolt and nuts retaining ignition coil (12029) and bracket. Position out of the way. 9. Remove heater water outlet tube retaining bolts and heater water outlet tube (18663) from water pump (8501) . 10. Disconnect lower radiator hose (8286) from water pump . 11. CAUTION: If using a prying device to assist in water pump removal, be careful not to damage the mating surfaces. Remove water pump retaining bolts, stud bolts and nuts. Remove water pump . Discard old water pump housing gasket (8507) . Installation 1. NOTE: Lightly oil all bolt and stud threads before installation except those specifying special sealant with SAE 5W-30 Super Premium Motor Oil XO-5W30-QSP or equivalent meeting Ford specification WSS-M2C153-G. Clean gasket surfaces on water pump and engine front cover (6019) . 2. NOTE: Gasket and Trim Adhesive F3AZ-19B508-B or equivalent meeting Ford specifications ESR-M11P17 and ESE-M2G52-A is recommended to hold the water pump housing gasket in position. Position a new water pump housing gasket on water pump sealing surface. 3. NOTE: The threads of the No. 1 water pump retaining bolt must be coated with Pipe Sealant with TeflonĀ® D8AZ-19554-A or equivalent meeting Ford specifications WSK- M2G350-A2 and ESR-M18P7-A before installing. Position water pump on the engine front cover . Install retaining bolts, stud bolts and nuts. Tighten retaining bolts and studs to 20-30 Nm (15-22 lb-ft). Tighten retaining nuts to 8-12 Nm (71-106 lb-in). 4. Inspect O-ring (replace as necessary) and install heater water outlet tube to water pump . Tighten retaining bolts to 8-12 Nm (71-106 lb-in). 5. Position coil and bracket assembly. Tighten retainers to 25 Nm (18 lb-ft). 6. Install lower radiator hose to water pump . Tighten clamps securely. 7. Install water pump-to-power steering pump brace and install water pump pulley .

Related entry:

1996 gmc how to remov waterpo manual pdf, removal of water pump on 05 corolla, 2007 pontiac g6 water pump location, 2003 buick century water pump installation, removing water pump on 2003 hyundai elantra, toyota tacoma water pump torque specs, Chevy express fan shroud removal, fuel flow npr, Water Pump Pontiac G6, toyota 2003 townace 3c enging timeming marke,

1994 Mercury Villager Water Pump REMOVAL AND INSTALLATION

0

Filed Under (Mercury) by admin on 03-04-2011

download
Water Pump Removal 1. Drain the cooling system. Refer to Section 03-03. 2. Disconnect the battery ground cable (14301) . 3. Remove the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05. 4. Raise and support the vehicle. 5. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley (8509) while removing the four water pump pulley bolts. 6. Remove the water pump pulley from the water pump (8501) . 7. Remove the crankshaft pulley (6312) . Refer to the procedure in this section 8. Remove the five lower engine front cover bolts and the lower engine front cover (6019) . NOTE: Make a note of the location of the one water pump bolt with the threads in the bolt head for ease of installation. 9. Remove the six water pump bolts. 10. Remove the water pump . Installation NOTE: Ensure the mating surfaces between the water pump and the cylinder block (6010) are cleaned of any sealant material. 1. Install a continuous 2.0-3.0mm (0.079-0.118 inch) wide bead of Gasket Maker E2AZ-19562-B or equivalent meeting Ford specification WSK-M2G348-A5, on the water pump and position the water pump on the cylinder block . NOTE: Refer to the note made during removal for the location of the bolt with the threads in the bolt head. 2. Install the six water pump bolts. Tighten the water pump bolts to 16-21 Nm (12-15 lb-ft). 3. Install the crankshaft pulley . Refer to the procedure in this section. 4. Position the water pump pulley on the water pump and install the four water pump pulley bolts. 5. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley , and tighten the four water pump pulley bolts to 16-21 Nm (12-15 lb-ft). 6. Install the lower engine front cover and the five lower engine front cover bolts. Tighten the five lower engine front cover bolts to 3-5 Nm (27-44 lb-in). 7. Lower the vehicle. 8. Install and adjust the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05. 9. Connect the battery ground cable . 10. Fill the cooling system. Refer to Section 03-03. 11. Start the engine (6007) and check for leaks.

Related entry:

1999 mercury mystique 4 cyl water pump replacement, 1HZ fuel injection pump setting procedures, water pump location on 2002 mercury sable, water pump bolt diagram instalation for 3 0 mercury sable, mazda 6 water pump pulley puller, how to replace 2011 ford escape water pump belt, how to remove vacuum pump and pully for a 1993 ford e 350 7 3, how to install a water pump drive belt on a 2009 ford escape, how to change a radiator on a 2002 mercury cougar, how instal td27 injector pump,

1998 Ford Taurus Fuel Pump Module Removal Installation

0

Filed Under (Ford) by admin on 15-02-2011

download
Removal 1. Remove fuel tank (9002) as described. 2. Remove any dirt that has accumulated around fuel pump module retaining flange. 3. Turn fuel pump module locking retainer ring counterclockwise using Fuel Tank Sender Wrench 310-002 (T74P-9275-A) and remove fuel pump module locking retainer ring. 4. Pull fuel pump module sender plate up out of fuel tank until locking tabs for fuel pump module are accessible. Reach through fuel pump module opening, squeeze both locking tabs together and remove fuel pump module from fuel tank . 5. Remove O-ring seal and discard. Installation 1. Clean fuel pump module retaining flange, fuel tank mounting surface and seal ring groove. 2. Apply a light coating of Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-BA on a new O-ring seal to hold it in place during assembly and install O-ring in seal ring groove. 3. Install fuel pump module carefully into fuel tank to make sure that filter, hoses and float rod are not damaged or binding. Align fuel pump module and fuel tank retainer and push fuel pump module into fuel tank retainer. A definite click will be heard when the two tabs on fuel pump module engage the fuel tank retainer. The fuel pump module must be snapped in the retainer with both tabs. Pull on fuel pump module to make sure it is fully engaged. Install fuel pump module sender plate to fuel tank , being careful that locating keys are in keyways and O-ring seal remains in place. 4. Hold assembly in place and install fuel pump module locking retainer ring finger-tight. Make sure that all locking tabs are under fuel pump module locking retainer ring tabs. 5. Secure fuel pump module unit by rotating fuel pump module locking retainer ring clockwise using Fuel Tank Sender Wrench 310-002 (T74P-9275-A) until fuel pump module locking retainer ring contacts the stops. 6. Install fuel tank in vehicle as described. 7. Lower vehicle. 8. Install a minimum of 38 liters (10 gallons) of fuel. Check for leaks. 9. Turn ignition switch to RUN position for three seconds repeatedly (5 to 10 times) until Multiport Fuel Injection (MFI) Fuel Pressure Gauge 310-012 (T80L-9974-B) or equivalent (depending upon application) shows at least 207 kPa (30 psi). Check for leaks at fittings. 10. Remove Multiport Fuel Injection (MFI) Fuel Pressure Gauge 310-012 (T80L-9974-B) or equivalent (depending upon application), start engine and recheck for leaks.

Related entry:

fuel pump test terminal 99 tahos, how to check the fuel pressure in a 95 cadillac deville, 89 G-20 chevy van prime fuel pump after installation, fuel pump on buick lucerne 3800 v6 2008 how do you change, jetta fuel system schematic diagram, 1973 corvette fuel pump replacement, E60 AIRBAG CONTROL MODULE LOCATION, 1997 neon ignition module, fuel pump on 02 audi a6, fuel pump pressure specs 2002 mercury sable 3 0 12 valve,