pajero fan belt Tension Pulley bearing replacement


You are searching repair manual in PDF format about pajero fan belt Tension Pulley bearing replacement use another keyword for search another post or files



  pajero fan belt Tension Pulley bearing replacement Direct Download speed 5787 Kb/s

  pajero fan belt Tension Pulley bearing replacement Full Version speed 6767 Kb/s




1998 Jeep Cherokee Drive Belt: Service and Repair

0

Filed Under (Jeep) by admin on 03-01-2011

download
Correct drive belt tension is required to ensure optimum performance of the belt driven engine accessories. There are different types of adjustment gauges for checking either a serpentine or a V-type belt. Use the correct gauge when checking belt tension. Place gauge in the middle of the section of belt being tested (between two pulleys) to check tension. Do not allow the gauge (or gauge adapter) to contact anything but the belt. BELT SCHEMATICS The belt routing schematics are published from the latest information available at the tingle of publication. If anything differs between these schematics and the Belt Routing Label, use the schematics on Belt Routing Label. This label is located in the engine compartment. BELT REPLACEMENT OR ADJUSTMENT- LEFT HAND DRIVE Belt tension is adjusted at the power steering pump bracket and idler pulley assembly. 1. Disconnect negative battery cable from battery. 2. Loosen idler pulley bolt at the power steering bracket. 3. Loosen adjusting bolt until belt can be removed from pulleys. 4. Remove belt. INSTALLATION 1. Check condition of all pulleys. CAUTION: When installing the serpentine accessory drive belt, the belt MUST be routed correctly. If not, the engine may overheat due to the water pump rotating in the wrong direction. 2. Install new belt. 3. Using serpentine belt tension gauge, tighten adjusting bolt until belt reaches proper tension. Refer to Belt Tension at the rear of this section for proper belt tension. 4. After belt is tensioned correctly, tighten idler pulley bolt to 47 Nm (35 ft. lbs.) 5. After idler pulley has been tightened into position, recheck belt tension. Adjust if necessary. BELT REPLACEMENT OR ADJUSTMENT- RIGHT HAND DRIVE (4.0L) 1. Disconnect negative battery cable from battery. 2. Loosen lower alternator mounting bolt and nut. 3. Loosen upper alternator mounting nut. 4. Loosen adjusting bolt at upper alternator bracket until belt can be removed from pulleys. 5. Remove belt. INSTALLATION 1. Check condition of all pulleys.

Related entry:

suzuki xl7 belt tensioner, honda civic hybrid 2005 drive belt tensioner, 2005 Jeep cherokee 3 7 limited automatic 4x4 wiring, jeep grand cherokee 2005 serpentine belt diagram, how many idler wheels on for fusion 4 cyl, belt routing diagram for a 2006 ford escape hybrid, 1996 ford 460 alt belt, how to put belts back on a 460 ford motor with 7 pulleys and 1 idler pulley, how to loosen belt for alternator 2006 saturn ion graph, change belt 08hhr,

1993-1997 Peugeot 306 Timing belt replacement intervals

0

Filed Under (Peugeot) by admin on 14-11-2010

download
Removal Removal 1. Raise and support front of vehicle. 2. Remove: RH front wheel. Engine undershield (if fitted). Lower inner wing panel. Auxiliary drive belt(s). 307: Engine tie-bars. Crankshaft pulley [1] . Timing belt upper cover [2] . Timing belt centre cover [3] . Timing belt lower cover [4] . 3. Turn crankshaft to setting position. Insert timing pins in camshaft sprocket and flywheel [5] & [6] . 4. Slacken tensioner nut to release tension on belt [7] . Lightly tighten nut. 5. Remove timing belt. Installation – -1997 Installation – -1997 1. Ensure timing pins located correctly [5] & [6] . 2. Fit timing belt in following order: Crankshaft sprocket. Camshaft sprocket. Water pump sprocket. NOTE: Ensure belt is taut between sprockets on non-tensioned side. Slacken tensioner nut [7] . Turn tensioner anti-clockwise to tension belt. Temporarily tighten nut. Remove timing pins [5] & [6] . Attach tension gauge to belt at [8] . Tool No.(-).0192/SEEM C.Tronic 105.5. Slacken tensioner nut [7] . Tension belt as follows: Turn tensioner anti-clockwise until tension gauge indicates 45 SEEM units. Tighten tensioner nut to 20 Nm [7] . Remove tension gauge. Turn crankshaft four turns clockwise to setting position. Ensure timing pins can be inserted [5] & [6] . Wait 1 minute to allow belt to settle. Apply firm thumb pressure to belt at . Attach tension gauge to belt at [8] . Tool No.(-).0192/SEEM C.Tronic 105.5. Slacken tensioner nut [7] . Turn tensioner anti-clockwise to tension belt. New belt: 40 SEEM units. Used belt: 36 SEEM units. Tighten tensioner nut to 20 Nm [7] . Remove tension gauge [8] . Turn crankshaft two turns clockwise. Ensure flywheel timing pin can be inserted [6] . NOTE: DO NOT allow crankshaft to turn anti-clockwise. Attach tension gauge to belt at [8] . Tool No.(-).0192/SEEM C.Tronic 105.5. Check tension gauge reading. New belt: 51±3 SEEM units. Used belt: 45±3 SEEM units. Install components in reverse order of removal. Tighten crankshaft pulley bolts to 8 Nm [9] . 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25.

Related entry:

1997 ford taurus 3 0 twenty four valve engine surpintine belt remove emovale, seem c tronic 105 5, 1997 asto van tenchenor, 1997 chrysler cirrus timing belt diagram, 1997 ford taurus 3 0 twenty four valve engine surpintine belt removale, 1997 mazda protege 1 5L how to instale yhr timing belt tensioner,

1994 Ford Aerostar/Ranger/Explorer Camshaft Timing ADJUSTMENTS

0

Filed Under (Ford) by admin on 08-03-2011

download
Checking Timing An access plug is provided in the cam drive belt cover so that camshaft timing can be checked without removal of the cover or any other parts. 1. Remove the access plug from the cam drive belt cover. 2. Rotate the crankshaft so that the No. 1 piston is rising on compression stroke. 3. Set the crankshaft to TDC by aligning the timing mark on the crank pulley with the TC mark on the belt cover. Always turn the engine in the direction of normal rotation (clockwise, as viewed from the front). Backward rotation may cause the timing belt to jump time, due to the arrangement of the belt tensioner. 4. Look through the access hole in the belt cover to make sure that the timing mark on the cam drive sprocket is lined up with the pointer on the inner belt cover. 5. Install the belt cover access plug. Adjusting Timing Belt SPECIAL SERVICE TOOL(S) REQUIRED Description Crankshaft Belt Tension Adjusting Tool T74P-6254-A 1. Remove the outer timing belt cover as outlined in this section. CAUTION: Attempting to adjust timing belt tension without loosening spring pivot bolt will break Crankshaft Belt Tension Adjusting Tool T74P-6254-A when relieving tension on the belt. 2. If belt timing or tension is incorrect, loosen timing belt spring pivot bolt. 3. Hold tensioner with Camshaft Belt Tension Adjusting Tool T74P-6254-A. 4. While holding tensioner, loosen adjusting bolt and gradually release spring tension. Loosening Timing Belt Tensioner, 2.3L Tool Number 8 — 5. Using adjusting tool, pry tensioner away from belt. While holding, tighten adjusting bolt. There should be no tension on belt. Camshaft Timing Belt, 2.3L I-4 Timing Mark on Camshaft Sprocket Remove the bolts holding the crankshaft position sensor in place and pull the sensor assembly free of the dowel pin. 7. Remove the crankshaft pulley , crankshaft pulley hub and timing belt guide. 8. Remove the drive belt and inspect it for wear or damage. If the belt is damaged, replace it. 9. Remove one spark plug from each cylinder. 10. If not done: a. Loosen tensioner adjusting bolt. b. Using Camshaft Belt Tension Adjusting Tool T74P-6254-A, pry tensioner clockwise against spring tension as far as possible. c. Tighten adjusting bolt to hold tensioner in released position. 11. Align crankshaft so number one piston is at TDC (top dead center) as indicated by timing mark. 12. Line up camshaft sprocket timing mark with inner timing belt cover timing mark and key is pointing down.

Related entry:

yhs-default, yhsm-imp1, 2008 ford edge timing belt or chain, how should the camshaft position be when the crankshaft is on its mark lexus is200 1G-fe, 4g33 timing marks, how to find compresion stroke on number one on 2005 hyundai tuson, 2000 volvo s40 timing belt replacement, 2000 toyota camry2 2liter timing belt diagram, diagram for 2005 chevy optra timing belt replacement, valve timing onk4m,

Ford Escort, Fiesta, Sierra, Mondeo, P100, 1.8 Diesel/Turbo diesel Camshaft Belt / Fuel Injection Pump Belt Common Causes of Failure

0

Filed Under (Ford) by admin on 05-06-2011

download
Common causes of camshaft timing belt failure on the above vehicles are due to incorrect operating tension, or ingress of dirt, water, or debris entering the timing belt cover. Predominantly on Fiesta models a high percentage of camshaft timing belt failures occur after the ancillary poly ‘V’ drive belt has failed, where strands of material off the broken belt have entered the timing belt cover. This is especially so where an ancillary belt has been fitted that does not contain “Kevlar” based materials. It is therefore important to always remove the timing belt cover to check for belt debris if the ancillary belt has failed. Any contamination that enters the timing belt cover can become compressed between the surfaces of the camshaft timing belt and drive pulleys. This causes wear to both the belt teeth, backing surface, and damage to the drive pulleys, resulting in premature failure of the camshaft timing belt. Later engines have modifications to improve the sealing of the belt cover around the crankshaft pulley, to reduce the level of outside contamination. Incorrect tensioning of the belt during installation will adversely affect the life of the belt. Before fitting a new belt it is important to check and observe the following points :- 1) Right Hand Inner Wing Splash Shield (Fiesta, Escort, Mondeo) This must be fitted and undamaged. 2) Timing Belt Cover Check that all components of the cover are fitted and undamaged. Ensure the latest type of modified cover is fitted. 3) a) Toothed Drive Pulleys Check that the tooth profiles are not worn or damaged. On vehicles built before January 1994 special attention should be given to the nylon toothed pulley situated below the camshaft pulley in a clockwise position on the belt drive (see diag item 4). This should be changed to a modified steel pulley (Ford No. 7053802) plus bolt (6701537). Ensure that the Camshaft and Injection Pump sprockets are free to rotate on the drive locations when the retaining bolts are slackened off. b) 4) a) b) c) Water Pump, Idler and Tensioner Pulleys Check that the belt running surfaces are not worn or damaged. Check that the flanges are running true and not damaged. Check that the water pump, and pulley bearings are in good condition, to ensure correct belt alignment. 5) Crankshaft Pulley The toothed pulley is in two parts. The rear section (Injection Pump Drive) is located onto the crankshaft by a small drive pin. The front section (Camshaft and “Poly V” belt drive) engages onto the rear pulley via a small vee protrusion on the rear face. Should the central fixing bolt for the crankshaft pulley come loose, or an old bolt re-used (Stretch bolt design), it is possible for fretting to take place damaging the locations. The crankshaft and camshaft pulleys can then move out of timing alignment, resulting in valve and piston contact damage. Replacement Procedure As the vehicle is fitted with two timing belts, one to drive the Camshaft, and one to drive the Injection Pump drives, which are driven off the crankshaft pulley, it is strongly recommended that both belts are replaced at the same time. NOTE: Special tools are required to lock the crankshaft, camshaft, and injection pump in the correct angular location when changing the belts, to ensure correct timing position. IMPORTANT: Ensure the engine is cold (not run for 4 hours) before commencing working as this will affect the setting of the timing belt tension and could lead to premature failure. Continued . . . .

Related entry:

1994 volvo 940 how to replace ac belt, ford diagram belts on 460 cid engine, 04 ford focus belt diagram, sable 1995 head lamps short no battery failed, 2006 chevy equiox sprpintine belt directions, auto repair reference about 1996 geo metro alternater attatching belts, pelacing the alternator belt in a 2001 Kia Sephia, alternator belt fitting mitsubishi colt 1 0 equippe, 1988 cadillac brougham belt diagram, 4d68 engine timing mark,

2000 Isuzu VehiCROSS Timing Belt: Service and Repair Removal Installation

0

Filed Under (Isuzu) by admin on 21-09-2010

download
Removal 1. Disconnect battery ground cable. 2. Remove air cleaner assembly. 3. Remove radiator upper fan shroud from radiator. 4. Move drive belt tensioner to loose side using wrench then remove drive belt. 5. 6. 7. 8. 9. 10. 11. 12. Remove cooling fan assembly four nuts, then the cooling fan assembly. Remove cooling fan drive pulley assembly. Remove idle pulley assembly. Remove serpentine belt tensioner assembly. Remove power steering pump assembly. Remove crankshaft pulley assembly using J-8614-01 crankshaft holder, hold crankshaft pulley remove center bolt, then the pulley. Remove right side timing belt cover then left side timing belt cover. Remove lower timing belt cover 2000 Isuzu Truck VehiCROSS (4WD) V6-3.5L  13. Remove pusher. Caution: The pusher prevents air from entering the oil chamber. Its rod must always be facing upward. 14. Remove timing belt. Caution: 1. Do not bend or twist the belt. otherwise its core could be damaged. The belt should not be bent at a radius less than 30 mm. 2. Do not allow oil or other chemical substances to come in contact with the belt. They will shorten the life. 3. Do not attempt pry or stretch the belt with a screw driver or any other tool during installation. 4. Store timing belt in a cool and dark place. Never expose the belt to direct sunlight or heat. Installation Note: For correct belt installation, the leper on the belt must be able to be read as viewed from the front of the vehicle. 2000 Isuzu Truck VehiCROSS (4WD) V6-3.5L  1. Install timing belt. 1. Align groove of crankshaft timing pulley with mark on oil pump. Align the mark on the crankshaft timing pulley with alignment mark (white dots line) on the timing belt. Secure the belt with a double clip. Note: When timing marks are aligned, No.2 piston will be on top Dead Center.

Related entry:

2002 NQR ISUZU SHIFTER, isuzu kb 250d tappet settings, 2005 isuzu ftr serpentine belt diagram, alterra manual transmission fluid, 02 nqr shift interlock, replacing t-belt on 02 trooper, liner removal tool isuzu npr 4bd2tc, isuzu dpd system, ISUZU 4JJ1 elf oil pump, how I can fix the battery light is on in isuzu npr 1989,