download
UNDER-DASH FUSE/RELAY BOX NOTE: Under-dash fuse/relay box is located under driver’s side of instrument panel. See Fig. 1 or Fig. 2 . Fig. 2: Locating Under-Dash Fuse/Relay Box (1998-2000) Fig. 3: Identifying Under-Dash Fuse/Relay Box Components (1996-2000) Fig. 4: Under-Dash Fuse/Relay Box Legend (1996-2000 – 1 Of 2) UNDER-HOOD ABS FUSE/RELAY BOX NOTE: Under-hood ABS fuse/relay box is located in passenger’s side of engine compartment, on strut tower. See Fig. 6 . Fig. 6: Locating Engine Compartment Fuse/Relay Boxes (1996-2000) Fig. 7: Identifying Under-Hood ABS Fuse/Relay Box Components & Legend (1996-2000)

download
Battery – Battery + Door function control module, driver Door function control module, passenger Door mirror adjustment motor, driver Door mirror adjustment motor, passenger Door mirror adjustment switch Earth point location 10 Earth point location 4 Earth point location 5 Earth point location 9 Electric window motor, driver Electric window motor, passenger Electric window switch, driver’s door Electric window switch, passenger door Fuse Fuse box/relay plate, engine bay Fuse box/relay plate, fascia 1 Ignition main circuits relay Ignition switch – ignition ON Multifunction control module Shorting link connector NOTE: In certain diagrams (Citroen, Peugeot & Renault), colour codes are replaced by numbers which are used to identify a particular cable and not the colour. In this instance, the cables will be numbered at each end close to the harness connector.

download
SYMPTOM DTC P1298 (electrical load detector (ELD) circuit high voltage) is stored in the ECM/PCM. PROBABLE CAUSE The electronic load detector (ELD) has a faulty solder joint. CORRECTIVE ACTION Replace the ELD. NOTE: Previously, if an ELD required replacement, you had to replace the under-hood fuse/relay box. To reduce repair costs, replacement ELDs are now available. PARTS INFORMATION Electronic Load Detector: P/N 38255-S5A-003, H/C 7987571 REPAIR PROCEDURE 1. Make sure you have the anti-theft code for the audio unit. Write down the customer’s audio presets. 2. Disconnect the negative battery cable from the battery. 3. Remove the under-hood fuse/relay box cover. 4. Release the three clips, and remove the under- hood fuse/relay box from the holder. CR-V only: Release the wire harness clip from the fuse/relay box holder CIVIC: 7. Remove the four screws that hold the two fuses, and remove the fuses. FUSE (Retain.) CIVIC: 80A CR-V: 100A FUSE (Retain.) CIVIC: 40A CR-V: 50A 12. Reinstall the 3P ELD connector and the lower fuse/ relay box cover. 13. Reinstall the fuse/relay box onto its holder. CR-V only: Reinstall the wire harness clip onto the holder. 14. Reinstall the fuse/relay box cover. 15. Reconnect the negative battery cable. 16. Do the idle learn procedure: • Make sure all electrical items (A/C, audio unit, defogger, lights, etc.) are off. • Start the engine and let it warm up to its normal operating temperature (the cooling fans cycle twice). • Let the engine idle (throttle closed and all electrical items off) for 10 minutes. 17. CR-V only: Reset the power window control unit: • Turn the ignition switch to ON (II). • Make sure the driver’s window is fully closed. • Push down and hold the window switch until the window goes all the way down. • Pull back and hold the window switch until the window goes all the way up, then hold the switch for at least 2 more seconds. 18. Enter the audio unit anti-theft code, and set the clock. Enter the audio presets.

download
The fuse/relay box is located in the left side of the engine compartment. Relay and Control Unit Locations Fuse Box and Fuse Location (Fuses 1 – 4) Fuse Box and Fuse Location (Fuses G, H, F10, F15, F22, F22/1,
F22/2) Fuse Box and Fuse Location (Fuses F24 & F24/1)

download
Connect the Saab Intelligent Tester (ISAT-86 10 651) scanner to Green diagnostic connector located under right front seat. Follow manufacturer’s test procedure to retrieve and erase DTCs. See ABS DTCS table. When fault-tracing ABS system, DO NOT directly probe ABS ECU connector pins. Use breakout box and breakout box lead connected between ABS ECU and connector. See Fig. 6 . Breakout box pin numbers are identical to ABS ECU terminal numbers. Problem ABS ECU Fault ABS ECU Fault (RAM) Defective System Relay No Signal From Left Front Wheel Sensor No Signal From Right Front Wheel Sensor No Signal From Left Rear Wheel Sensor Diagnose all other DTCs before diagnosing DTCs 42251 or 1. Breakout box pin numbers and ABS ECU terminal numbers are identical. 1. Turn ignition switch to RUN position. Check for battery voltage between breakout box pins No. 1 and 3, and pins No. 1 and 33. If no voltage is present at either pin No. 3 or 33, check ABS 30-amp fuse in main bulkhead fuse box. Also check Red wire from fuse to main relay and distribution block on battery tray. 2. If wiring is okay but voltage is still not present, ensure continuity is present between breakout box pin No. 3 and relay terminal No. 30 (White wire), and between breakout box pin No. 33 and relay terminal No. 87a (Black wire). Ensure 10-amp ABS fuse is okay.