pontiac pusuit stereo wiring
You are searching repair manual in PDF format about pontiac pusuit stereo wiring use another keyword for search another post or files
pontiac pusuit stereo wiring Direct Download speed 5787 Kb/s
pontiac pusuit stereo wiring Full Version speed 6767 Kb/s
Filed Under (Pontiac) by admin on 17-08-2010
Installation Instructions Part Number 200-630 2008-09 Buick Enclave 2008-09 Chevrolet Equinox Sp. 2008-09 Chevrolet Malibu 2008-09 Chevrolet Traverse 2008-09 GMC Acadia 2008-09 Pontiac G6 GXP 2008-09 Pontiac G8 2008-09 Pontiac Torrent GXP 2008-09 Saturn Outlook 2008-09 Saturn Vue XR 2008-09 Suzuki LX7 3.6L V-6 2. Disconnect the breather hose elbow from the intake tube. Loosen the two hose clamps that secure the intake tube to the throttlebody, and the mass air flow sensor. Remove the air intake tube. 1. Disconnect the negative battery cable! Remove the oil fill cap and set it aside. Lift straight up on the engine beauty cover and set it aside. Reinstall the oil fill cap after the beauty cover has been re- moved to prevent any foreign material from entering the crank- case. 3. Remove the four bolts that secure the throttlebody to the in- take manifold. 5. Install the provided bolts and washers thru the throttlebody and Poweraid Spacer and tighten to the manufacturer’s specifi- cations. 4. Install the Poweraid Spacer between the throttlebody and the intake manifold with the first supplied gasket next to the intake manifold, and the second supplied gasket next to the throttle- body as shown. Make sure the “flow” arrow printed on the spacer is pointing towards the intake manifold. 6. Reinstall the intake tube, tighten the two hose clamps, and reconnect the crankcase breather tube. Reinstall the beauty cover, and oil cap in the reverse order that they were removed. Re-connect the negative battery cable!
Filed Under (Chevrolet) by admin on 12-06-2010
Condition Some customers may comment on any of the following concerns: • The shifter is hard to move or binds. • They cannot remove the ignition key. • It takes high effort to rotate the key. Cause 1 The shifter button may be sticking in the handle. Cause 2 The pin that activates the micro-switch may have moved out of position (refer to illustration above). This causes the micro-switch to fail to engage when the vehicle is placed in Park. If this condition is present, the customer will not be able to remove the key from the ignition. The illustration above shows the switch in a correct position. Cause 3 Metal flashing left in the cylinder may cause a high effort to rotate the key. Cause 4 The slider may be binding in the guides. This may cause the shifter to become difficult to operate. Correction 1 Verify that the shifter button is inoperative by evaluating if the park pawl pin on the shifter assembly moves when activating the button. If the parking pawl does not move when the button is activated, the shifter handle will have to be replaced. Refer to Floor Shifter Control Knob Replacement in SI.
The following diagnostics might be helpful if the vehicle exhibits the conditlon(s) described above. Use the appropriate recommendation based on what symptom has occurred. Recommendation/Instructions No DTCs Review Corporate Bulletin Number 05-02-32-002B to assure you do not have a blown 60 amp steering fuse. The fuse can be blown during improper jump starting of the vehicle on the HHR and ION. Check for this particularly for tow in conditions. DO NOT replace the steering column unless an internal short has been Identified in the column that is causing fuse to blow. Power Steering Warning Message on DIC with DTCs C0176 and C0476 This condition is often the result of excessive lock-to-lock turns of the steering wheel, causing the thermal protection in the Power Steering Control Module (PSCM) to take the steering motor temporarily off line. This is a normal operating characteristic of the system. DO NOT replace the steering column for this condition. Refer to Corporate Bulletin Number 06-02-32-002B for additional information
Filed Under (Chevrolet) by admin on 19-03-2011
DEFOGGERS Fig. 1: Defogger Circuit HORN Fig. 2: Horn Circuit POWER ANTENNA Fig. 3: Power Antenna Circuit POWER DOOR LOCKS Fig. 4: Power Door Lock Circuit POWER SEATS Fig. 5: Power Seat Circuits POWER WINDOWS Fig. 6: Power Window Circuit, 2 Door RADIO Fig. 7: Mono Radio Circuit Fig. 8: Stereo Radio Circuit STARTING/CHARGING Fig. 9: Charging Circuit Fig. 10: Starting Circuit TRUNK, TAILGATE, FUEL DOOR Fig. 11: Trunk Release Circuit WIPER/WASHER Fig. 12: 2-Speed Wiper/Washer Circuit Fig. 13: Interval Wiper/Washer Circuit PART 2 Fig. 1: Engine Compartment Fig. 2: Engine Compartment (Cont.) Fig. 3: Fuse Block & Underdash Fig. 4: Underdash (Cont.) & Instrument Panel Fig. 5: Instrument Panel (Cont.) Fig. 6: Rear Compartment & Accessories SUB-SYSTEM WIRING DIAGRAMS CANADIAN MODELS Fig. 7: Kicker System Wiring Diagram (5.0L “B” Body A/C) Fig. 8: A/C Kicker System (3.8L “B” & “G” Body) Wiring Diagram Fig. 9: Electric Choke Heater (3.8L “B” & “G” Body) Wiring Diagram Fig. 10: Electric Choke Heater (3.8L “B” Body Without Gauges) Fig. 11: Electric Choke Heater (5.0L “B” & “G” Body) Fig. 12: Early Fuel Evap System (“B” & “G” Body) Wiring Diagram Fig. 13: TCC (“B” & “G” Body, 3 or 4-Speed Auto. Trans.)
Filed Under (Acura) by admin on 03-08-2010
SRS wire harnesses are routed near the steering column and passenger’s side dashboard. CAUTION: All SRS wiring harnesses are covered with yellow outer insulation. Before disconnecting any part of the SRS wire harness, install the short connectors. Replace the entire affected SRS harness assembly if it has an open circuit or damaged wiring. STEREO RADIO/CASSETTE REPLACEMENT NOTE (L and LS models): These versions have a stereo radio/cassette player with a 5-digit coded theft protection circuit. Be sure to get the code number before: -disconnecting the battery. removing the No. 56 (7.5 A) fuse. removing the radio. After reconnecting power and turning the radio ON, the word “CODE” will be displayed. Then enter the code. 1. Remove the center console panel.