Auto Repair Manual Free Download and ReviewsFree download ebook pdf files automotive manual

download
SERVICE PROCEDURE Front Door Glass Bolt Replacement Caution: Avoid hands and face being caught by the front door glass when adjusting the height of the front door glass. 1. Adjust the front door glass to align the position of the front door glass bolt with the service hole. 2. Approximately 100 mm (4 in) from the top of the front door trim board, mark off 80 mm (3 in) with tape. 3. Adjust the front door window glass to align with the tape marking. Notice: Unhook the clip before unhooking the claw to prevent breaking the bracket garnish. 4. Remove the clip and unhook the claws to remove the front door lower frame bracket garnish. Notice: Wrap protective tape around the head of the flathead screwdriver to avoid scratching the power window switch or trim board. 5. Using a flathead screwdriver with protective tape wrapped around the head, remove the six (6) clips and claws to separate the power window switch. 6. Remove the power window switch: For LH – Unlock and remove the connector. Refer to the illustration. 2092983 – For RH (with door lock switch) – Disconnect the two (2) connectors. – For RH (without door lock switch) – Disconnect the connector. 2092928 7. Remove the screw from the door pull handle, and remove the handle. Notice: Wrap protective tape around the head of the flathead screwdriver to avoid scratching the power window switch or trim board. 8. Remove the screw. 9. Remove the front door trim board. Notice: Avoid damaging the inside handle when removing the trim board. 10. Remove the eight (8) clips and remove the trim board. Notice: Pull the service cover up carefully to avoid damaging the service cover. Notice: Do not allow butyl tape to adhere to any parts. 11. Pull up on the service hole cover until the bolt for the front door glass is visible, and then secure the cover in place with tape.

repair and service manual covers Toyota Matrix and Pontiac Vibe, U.S. and Canadian models, 2003 to 2008 with an inline four-cylinder engine. The engine drives the front wheels through either a five-speed manual or a four-speed automatic transmission.

Table of Contents

Introduction: About this manual | Introduction | Vehicle identification numbers | Maintenance techniques, tools and working facilities | Buying parts | Jacking and towing | Booster battery (jump) starting | Conversion factors | Automotive chemicals and lubricants | Safety first! | Troubleshooting

download
MODELS: 2008 Chevrolet Captiva Sport (Mexico) 2009 Chevrolet Aveo Sedan (Mexico & Argentina) 2009 Pontiac G3 (Mexico) 2008 Saturn VUE (U.S. & Canada) with Body-Color Outside Door Handles 1. Remove all four outside door handles. Refer to Front Side Door Outside Handle Replacement and Rear Side Door Outside Handle Replacement in SI. 2. Install chrome door handles. Refer to Front Side Door Outside Handle Replacement and Rear Side Door Outside Handle Replacement in SI.

download
Subject: Models: EI09073 – Front and Rear Door Adjustment and/or Alignment for Water Leak, Windnoise, Clunk, Creak, Rattle, Rumble, Squeak, Binds, Excessive Effort to Close, Poor Fit, Misaligned (Engineering Information) 2009 Buick Enclave 2009 Cadillac Escalade, Escalade EXT, Escalade ESV 2009 Chevrolet Avalanche, Cobalt (Built After VIN Breakpoint 97272611), Colorado, Malibu, Silverado, Suburban, Tahoe, Traverse 2009 GMC Acadia, Canyon, Sierra, Yukon, Yukon XL 2009 Pontiac G5 (Built After VIN Breakpoint 97272611) 2009 Saturn OUTLOOK Some customers may comment about one or more of the following conditions with the front and/or rear doors – water leak, wind noise, clunk, creak, rattle, rumble, squeak, binds, excessive effort to close, difficult to open, inoperative, loose, fits poorly or is mis-aligned. Use this bulletin If, based on preliminary diagnosis, the technician feels that an adjustment and/or alignment of the door(s) will correct the customer complaint or if the vehicle displays an issue where the following labor codes would be used: B4000/B4001 (Front Side Door Adjustment – LH & RH) and/or B4400/B4401 (Rear Side Door Up/Down Adjustment – LH & RH). Cause GM Engineering is attempting to determine the “root cause” for the concern with side door alignment. GM Engineering has a need to obtain information first-hand during the diagnosis and repair. As a result, this information will be used by engineering to “root cause” the customer’s concern and develop a field fix. Instructions Important: DO NOT perform any alignment and/or adjustment to the front and/or rear door

download
Removal Procedure 1. Open the door. 2. Remove the front door trim plate. Refer to Door Trim Plate Replacement () . 3. Remove the front door manual window regulator handle if equipped. Refer to Window Regulator Handle Replacement – Door Remove the armrest screws. Route the electrical harness through the front door trim panel opening. Use J 38778 in order to remove the front door trim panel from the door. Use J 38778 in order to pry the front door trim panel from the door frame at the window seal. 8. Remove the front door trim panel from the door. 4. 5. 6. 7. Installation Procedure 1. Install the front door trim panel to the front door. 2. Place the window seal portion of the panel over the door frame. 3. Route the electrical harness through the front door trim panel opening and into place. 4. Align the front door trim panel retainers to the holes in the door metal. 5. Firmly press the front door trim panel to the door metal in order to seat the retainers. Notice: Refer to Fastener Notice in Cautions and Notices. 6. Install the armrest screws. Tighten the screws to 3 N.m (26 lb in). 7. Install the front door manual window regulator handle if equipped. Refer to Window Regulator Handle Replacement – Door 8. Install the door trim plate. Refer to Door Trim Plate Replacement () . 9. Close the door.