power locks on a 96 audi a4 not working


You are searching repair manual in PDF format about power locks on a 96 audi a4 not working use another keyword for search another post or files



  power locks on a 96 audi a4 not working Direct Download speed 5787 Kb/s

  power locks on a 96 audi a4 not working Full Version speed 6767 Kb/s




1995 Ford Contour Hoses Pressure and Return REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 15-02-2011

download
Removal 1. Disconnect battery ground cable. 2. Disconnect power steering pressure (PSP) switch electrical connector. 3. Remove power steering pressure (PSP) switch from power steering pressure hose. 4. On 2.0L engine, remove one nut, two bolts and disconnect power steering pressure hose from power steering pump bracket and engine lifting bracket. 5. On 2.5L engine, remove one bolt and disconnect power steering pressure hose from front engine support insulator. 6. Remove power steering pump auxiliary reservoir as outlined. 7. Raise vehicle on hoist. Refer to Section 00-02. 8. Remove front sub-frame. Refer to Section 02-01. 9. Remove six bolts and steering gear cover plate from front sub-frame. 10. Disconnect power steering pressure hose and power steering return hose unions from steering gear. 11. Remove two bolts retaining power steering pressure and return hoses to front sub-frame and remove power steering pressure and return hoses. CAUTION: Whenever the power steering pressure and return hoses and/or steering gear are disconnected, the power steering pressure and return hoses and/or steering gear should be plugged to prevent system contamination. If the power steering system becomes contaminated with dirt or other foreign matter, power steering pump and/or steering gear failure may result. Installation 1. Position power steering pressure and return hoses to front sub-frame and secure with two bolts. Tighten bolts to 28 Nm (21 lb-ft). 2. Connect power steering pressure hose and power steering return hose unions to steering gear. Tighten unions to 31 Nm (23 lb-ft). 3. Install steering gear cover plate and secure with six bolts. Tighten bolts to 50 Nm (37 lb-ft). 4. Install front sub-frame. Refer to Section 02-01. 5. Lower vehicle. 6. Install power steering pump auxiliary reservoir as outlined. 7. On 2.5L engine, connect power steering pressure hose to front engine suppor t insulator and secure with one bolt. Tighten bolt to 6 Nm (53 lb-in). 8. On 2.0L engine, connect power steering pressure hose to power steering pump bracket and engine lifting bracket. Secure with one nut and two bolts. Tighten nut and bolts to 6 Nm (53 lb-in). 9. Install power steering pressure (PSP) switch into power steering pressure hose. 10. Connect power steering pressure (PSP) switch electrical connector. 11. Connect battery ground cable. 12. Refill power steering fluid as necessary and bleed system. Refer to Section 11-00. Hose Fittings, Pressure and Return Line at Steering Gear and Pump

Related entry:

diagram of 2001 ford winstar power steering line, no power to dlc 98 chev lumina, how to service volkswagen polo 2004 power steering fluid, how to tighten power steering belt on eclipse, mazda 2011 3 power steering fuse, mazda 3 power steering failure, nissan equinox primary power schematic, power steering pump 02 rodeo, Power Steering Pump removal 2007 F150, power steering sendsor location 2000 neon,

2005-2010 Chevrolet Cobalt Loss of Power Steering Assist – Replace Electric Power Steering Motor

0

Filed Under (Chevrolet) by admin on 01-01-2011

download
SUBJECT: MODELS: Loss of Power Steering Assist – Replace Electric Power Steering Motor 2005-2010 Chevrolet Cobalt 2005 Pontiac Pursuit 2005-2006 Pontiac G4 2006 Pontiac G5 Pursuit 2007-2010 Pontiac G5 Equipped with Electric Power Steering 2005-2010 model year Chevrolet Cobalt vehicles; 2005 model year Pontiac Pursuit; 2005-2006 model year Pontiac G4; 2006 model year Pontiac G5 Pursuit; and 2007-2010 model year Pontiac G5 vehicles equipped with electric power steering. Some of these vehicles have a condition in which a sudden loss of power steering assist could occur at any time while driving the vehicle. If the power steering assist is lost, a chime will sound and a “Power Steering” message will be displayed in the Driver Information Center to inform the driver of the condition. Steering control will be maintained, as the vehicle defaults to a manual steering mode. If power steering assist is lost, it may require greater driver effort at low vehicle speeds, for example, below 15 mph (25 km/h). Unless a driver compensates for this additional effort, it may increase the risk of a crash. Typically, the next time the vehicle is started, the power steering assist will return and the “Power Steering” message will no longer be displayed. EPS Motor Replacement Procedure Note: The use of Loctite is no longer required. Loctite should not be used for any further applications. 1. Connect the Tech 2® to the vehicle and check for diagnostic trouble codes (DTCs). 2. Record any present DTCs on the repair order and during claim submission. 3. Clear any DTCs that are present. 4. Remove the power steering assist motor. Refer to Power Steering Assist Motor Replacement in SI. Note: For 2005 model year vehicles only: Do NOT install the o-ring between the motor assembly and the steering column assembly. The new service motor kit will include an o- ring, but DO NOT install the o-ring for 2005 model year vehicles only. 5. Install the new power steering assist motor. Refer to Power Steering Assist Motor Replacement in SI. 6. Perform Test Drive.

Related entry:

2005 pontiac wave center bore size, diagram of heater acuators in 2005 pontiac vibe, free repair manuals for 2005 pontiac wave 5, honda accord seat wiring, 2010 fusion 2 5l engine belt routing, Free 2005 Pontiac Vibe repair manual, 2005 kia sedona removal steering joint from rack and pinion, pontiac vibe 2005 pcm location, sunfire 2005 tach wire, heat resistor 2005 pontiac vibe,

2001 Buick Regal Power Steering Pump Replacement

0

Filed Under (Buick) by admin on 03-07-2010

download
1. Place a drain pan under the vehicle. 2. Remove the accessory drive belt. Refer to Drive Belt Replacement in Engine. 3. Raise and support the vehicle. Refer to Vehicle Lifting. 4. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation. 5. Remove the power steering pressure hose from the power steering pump. Refer to Power Steering Pressure Hose Replacement. 6. Remove the power steering return hose from the power steering pump. Refer to Power Steering Return Hose Replacement . 7. Remove the power steering mounting bolts from the power steering pump. 8. Remove the power steering pump. 9. Remove the power steering pump reservoir from the power steering pump. 10. Transfer the power steering pump pulley. Refer to Power Steering Pulley Replacement Installation Procedure 1. Install the power steering pump reservoir to the power steering pump. 2. Position the power steering pump to the engine. Notice: Refer to Fastener Notice in Service Precautions. 3. Install the power steering pump mounting bolts. Tighten the mounting bolts to 34 Nm (25 ft. lbs.) .

Related entry:

switch to lower the driver seat 04 buick regal,

2004–2008 Acura TSX Power Steering Feed Hose Leak

0

Filed Under (Acura) by admin on 04-01-2011

download
BACKGROUND Prolonged high under-hood temperatures may cause the power steering hose to deteriorate prematurely and may cause the hose to crack and leak power steering fluid. Power steering fluid leaking onto a hot exhaust pipe will generate smoke and could lead to an under- hood fire. CORRECTIVE ACTION Install a power steering feed hose kit. PARTS INFORMATION Power Steering Feed Hose Kit: P/N 06530-SEC-A00 (Contains power steering feed hose [with power steering pump-side O-ring attached] and power steering pressure switch O-ring.) REPAIR PROCEDURE NOTE: Take care not to spill power steering fluid on the body and other parts. Wipe off any spilled fluid at once. 1. Raise the power steering reservoir, then disconnect the return hose, and drain the reservoir. Plug the return hose nipple with a suitable cap. POWER STEERING RESERVOIR 6. Remove the power steering heat shield, then lower the vehicle to the ground. RETURN HOSE HOSE 7. Disconnect the power steering pressure switch connector. UPPER LEVEL LINE CONNECTOR 2. Connect a hose of suitable diameter to the disconnected return hose, and put the hose end in a suitable container. 3. Start the engine, let it run at idle, and turn the steering wheel from lock-to-lock several times. When fluid stops running out of the hose, shut off the engine. Discard the fluid. NOTE: Inspect the reservoir screen for any debris. If the reservoir screen is clogged, replace the reservoir. 4. Remove the cap from the return hose nipple on the reservoir, then reinstall the return hose on the reservoir. 5. Raise the vehicle on a lift, and make sure it is securely supported. POWER STEERING PRESSURE SWITCH

Related entry:

where is the a/c drain on a 2004 impala, vacuum canister on 2004 ford freestar 3 9,

1999 Ford Taurus Steering Gear Base REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 19-02-2011

download
1. Open hood. 2. Disconnect battery ground cable (14301). Refer to Section 14-01. 3. From inside vehicle, remove nuts retaining steering column tube boot (3C611) to cowl panel. 4. Remove bolt retaining steering column intermediate shaft coupling (3A525) to steering column lower yoke (3N725) . 5. Position steering column tube boot out of the way. Remove pinch bolt retaining steering column intermediate shaft coupling to power rack and pinion steering gear and remove steering column intermediate shaft coupling . 6. Raise vehicle on a twin post hoist and remove front wheel and tire assemblies. 7. Remove exhaust system flex tube-to-dual converter Y-pipe attachment. Disconnect heated oxygen sensor wiring harness. Remove dual converter Y pipe (5F250) from vehicle. Dual Converter Y Pipe Removal 8. Support vehicle with jack stands under rear edge of front sub-frame (5C145). 9. Remove tie rod cotter pins and nuts, and remove tie rod end (3A130) from RH front wheel knuckle (3K185) and LH front wheel knuckle (3K186). 10. Remove tie rod end from front wheel spindle tie rod (3280) . Mark position of jam nut to maintain alignment. 11. Remove nuts from steering gear-to-front sub-frame retaining bolts. 12. Remove rear sub-frame-to-body retaining bolts. 13. Raise twin post hoist carefully until rear sub-frame (5R003) separates from body approximately 102 mm (4 inches). 14. Remove heat shield push-pin retainers from power steering hose bracket (3C510). Remove steering shaft U-joint shield (3F540). 15. Remove screw and power steering left turn pressure hose (3A714) from power steering hose bracket . Remove two screws and power steering hose bracket. 16. Remove LH stabilizer bar link (5K484). 17. Disconnect power steering pressure switch electrical connector. 18. Rotate power rack and pinion steering gear to clear bolts from front sub-frame and pull left to ease line fitting removal. 19. Place a drain pan under vehicle and remove hydraulic power steering pressure hose and power steering return hose from fittings on power rack and pinion steering gear. 20. Remove power rack and pinion steering gear assembly through LH wheel well. Installation 1. Install new Teflon® O-rings on both line connector assemblies as described under Quick Connect Power Steering Fitting—Seal Replacement. 2. Place steering gear retaining bolts in steering gear housing (3548). 3. Install power rack and pinion steering gear through LH wheel well. 4. Install power steering hose bracket and two screws. Tighten to 9-12 Nm (80-106 lb-in). 5. Install hydraulic power steering pressure hose and power steering return hose to fittings on power rack and pinion steering gear. Tighten hoses to 33-41 Nm (25-30 lb-ft). 6. Install power steering pressure hose and and screw. Tighten to 9-12 Nm (80-106 lb-in). 7. Connect power steering pressure switch electrical connector. 8. Position power rack and pinion steering gear into front sub-frame. 9. Install tie rod ends onto front wheel spindle tie rods . 10. Install push-pin retainers at top of heat shield. 11. Install tie rod end to RHfront wheel knuckle and LH front wheel knuckle. Install nuts and tighten to 47-63 Nm (35-46 lb-ft). Install new cotter pins. 12. Install LH stabilizer bar link. Tighten to 76.5-103.5 Nm (57-76 lb-ft).

Related entry:

how to replace intermediate shaft 2007 pontiac g5, 2007 g5 pontiac intermediate steering shaft, 07 arcadia rack removal, Ford Ka Steering Rack Diagram, inter steer shaft for 2008 malibu, replacing steering column turn indicator on 2008 malibu, silverado power steering pump bolt torque, suzuki ignis steering rack joints, town and country power seat motor worm drive, where to buy a intermediate steering shaft for 2007 buick lacrosse,