download
Keys, doors, windows, sunroof To raise Turn the rotary switch to any position between d and e. The sunroof w ill automatic ally move to the desired position. When the rotary switch is in position e, the sunroof is fully raised. To lower Turn rotary switch to d. Posit ion memory After the ignition has been switched on, the sunroof c an be automatically returned to its last position b y briefly pressing the rotary switch. Safety function If the sunroof encounters resistance during automatic closing, it is immediately stopped and opened again, as long as the vehicle is stationary. Operated using rotary switch in the overhead control panel. To open Turn the rotary switch to any position between d and ü. The sunroof will automatically move to the desired position. When the switch is in position ü , the sunroof is fully opened . Com fort position Set rotary switch to position f. With the roof in this position, w ind noise is reduced. To close: Turn rotary switch to d. 9 Warning Closing sunroof from outside To close the sunroof from outside with the remote control: Press button p until the sunroof is closed. If the electric windows 3 are to be closed from outside the vehicle, but the sunroof is to be left op en, briefly press the rotary switch before switching off the ignition. Automatic closing 3 See page 33. If when the vehicle is being driven the sunroof encounters resistance during automatic closing, because of the higher closing forces involved the protective function cannot be guaranteed, and there is a risk of injury. If the sunroof movement is stiff, e.g. due to frost, turn rotary switch to d and keep it pressed until the sunroof is closed. Keys, doors, windows, sunroof Sunshade To reduce the sunlight in the interior with the sliding roof closed or raised. O pen or close sunshade as required. When the sunroof is opened, the sunshade is also opened. Overload If the sy stem is overloaded, the power sup ply is automatically cut off for a short time. Fault If the sunroof no longer assumes the desired position automatically , programm e sunroof electronics as follow s: 1. Switch on ignition. 2. Press the rotary switch until the sunroof is shut, then keep it pressed for a t least a further 3 seconds. 3. Turn rotary switch to ü and keep it depressed until the sunroof is open. 4. Turn rotary switch to d and keep it depressed until the sunroof is closed . 5. Turn rotary switch to e and leave there until the sunroof is fully raised. 6. Turn rotary switch to d and keep it depressed until the sunroof is closed . Electrically operated rear window blind 3 Reduces intensity of sunlight shining on to rear seats. Operation w ith ignition switched on. To raise To lower = = Do not operate blind if there are objects lying in front of the rear window. Sun blinds for rear door windows 3 To reduce sunlight a t the rear seats. Pull the blind upwards using the grip and engage it at the top in the door frame. Press N Press N again

download
Certain 2008 model year Buick Enclave; 2007-2008 model year GMC Acadia and Saturn OUTLOOK vehicles equipped with a sunroof may have a condition in which water is not properly drained away from the sunroof. If this condition were to occur, water may enter the interior of the vehicle and dampen the carpet, upholstery, and other interior components. Correction Dealers/retailers are to install drain tube extension assemblies, and ensure that the water drains properly

download
SYMPTOM/CONDITION: DIAGNOSIS: 1. Verify the rear of the sunroof glass to roof flushness concern. 2. UNCALIBRATE THE SUNROOF. a. b. c. d. e. 3. RECALIBRATE THE SUNROOF a. b. c. 4. If the uncalibrate/recalibrate procedure did not eliminate the sunroof glass to roof fit, use the procedures outlined in TechCONNECT(R) BODY/SUNROOF/GLASS PANEL/ADJUSTMENTS to adjust the glass panel. If the sunroof glass is now flush, perform the Repair Procedure. If the vehicle operator describes or experiences the Symptom/Condition, perform the Repair Procedure. Insure the battery is at least 12 Volts. Place the ignition switch in RUN position. Locate the sunroof fuse (Fuse 44 in the Power Distribution Center located in the trunk). While the sunroof is still in motion, have an assistant remove the sunroof fuse. Reinstall the sunroof fuse. Press and hold the sunroof vent switch until it stops at the full vent position. Verify sunroof operation by opening, closing, and venting the sunroof. If the uncalibrate/recalibrate procedure corrected the sunroof glass to roof fit, perform the Repair Procedure.

download
4Runner FJ Cruiser Land Cruiser Sequoia Tacoma Tundra 1GR 2UZ 2006 2007 1GR 2006 2007 2UZ 2006 2UZ 2006 1GR 1GR 2UZ 2006 Example: 06 A P 0 00001 06: Year of Manufacture A: Month of Manufacture (A – M, “I” not used) P: Transmission Model Code (A750*) (A750 ) 0: Plant Code 00001: 5 Digit Serial Number 5–Digit Location: Right Rear on Transmission Case Above Transmission Pan (as shown below) Camry 2006 2AZ Highlander 2006 2007 3MZ RAV4 2006 2GR Example: 06 A L 0 00001 06: Year of Manufacture A: Month of Manufacture (A – M, “I” not used) L: Transmission Model Code (U15#) 0: Plant Code 00001: 5 Digit Serial Number 5–Digit Location: Slightly Off Center to the Left on Top of Bell Housing of Transmission (as shown below)

download
Some vehicles equipped with the folding soft top may experience water accumulation in the foot wells due to the soft top drains becoming clogged with leaves and other debris. 1736a DRAIN COVER DRAIN VALVE ASSEMBLY As mass production changes: – A filter has been added to the drain valve assembly to prevent leaves or other foreign substance from clog- ging the drain. – Ribs have been added to the upper and lower valves of the drain valve assembly to prevent the valves (rub- ber flaps) from being forced out of position in the event compressed air is used to clear the drains from under the vehicle. – A foam urethane filter has been established for the drain cover. Vehicles with clogged drains should have the drain assemblies updated as described in the following repair pro- cedure, also included in this bulletin are maintenance tips for the customers to perform to ensure dependable operation of these drains. REPAIR PROCEDURE NOTE: Removal of the soft top is not required to perform the repair procedure. Illustrations in this bulletin are for component identification and location purposes only. 1. Verify customer concern. 2. Remove rear package trim according to Workshop Manual (section 09 -17 REAR PACKAGE TRIM REMOVAL/INSTALLATION) and related components, then remove the left and right side shelves according to Workshop Manual (section 09-17 SIDE SHELF REMOVAL/INSTALLATION). 3. Remove the seat belt retractors and covers according to Workshop Manual (section 08-11 SEAT BELT REMOVAL/INSTALLATION). – - TYPE A VEHICLES: Proceed to next step. TYPE B VEHICLES: Proceed to “TYPE B VEHICLES” under DRAIN VALVE REPLACEMENT. 4. Using seat belt retractor holes for access, remove the drain valve assemblies. DRAIN COVER FILTER INSTALLATION 1. Clean and degrease the drain cover assemblies.