You are searching repair manual in PDF format about rav4 rattle use another keyword for search another post or files
rav4 rattle Direct Download speed 5787 Kb/s
rav4 rattle Full Version speed 6767 Kb/s
Filed Under (Toyota) by admin on 03-06-2010
Some 2001 — 2003 model year RAV4 vehicles equipped with an automatic transaxle may exhibit a harsh shift condition and/or M.I.L. “ON” with DTC P0750, P0753, P0755, P0758, and/or P1760 stored. Improvements have been made to the Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) manufacturing process to reduce the possibility of this condition occurring. Use the following procedure to repair the vehicle. S 2001 – 2003 model year RAV4 vehicles equipped with automatic transmission.Inspection 1. If the vehicle is currently exhibiting a harsh shift condition and/or M.I.L. “ON” with Procedure DTC P0750, P0753, P0755, P0758, and/or P1760 stored, refer to the Technical Information System (TIS), 2001 — 2003 model year RAV4 Repair Manual: -
Filed Under (Toyota) by admin on 26-08-2009
Haynes New Toyota RAV4 Petrol & Diesel (94 – Jan 06) L to 55
RAV4 models, two-wheel-drive and four-wheel-drive, inc. special/limited editions.
Does not cover new RAV4 range introduced Feb 2006..
Petrol: 1.8 litre (1794cc) & 2.0 litre (1998cc)
Diesel: 2.0 litre (1995cc)
Filed Under (Chevrolet) by admin on 14-11-2010
Model(s): 1994-95 Buick Regal 1994-97 Buick Skylark 1994-98 Buick Century 1994-95 Chevrolet Beretta Corsica, Lumina, Monte Carlo 1996-98 Chevrolet Venture 1997-98 Chevrolet Malibu 1993-97 Oldsmobile Cutlass Supreme 1994-96 Oldsmobile Cutlass Ciera 1994-97 Oldsmobile Achieva 1996-98 Oldsmobile Silhouette 1997-98 Oldsmobile Cutlass 1994-98 Pontiac Grand Am, Grand Prix 1996-98 Pontiac Trans Sport with 3100, 3400 V6 Engine (VINs M, E – RPOs ticking type noise that begins shortly after cold engine start-up and gradually diminishes as the engine warms up. In most cases, the noise is gone after five (5) minutes. In severe cases, the noise may not disappear when lhe engine is hot. Under normal design tolerances when the piston pin bore is produced at the maximum tolerance and the piston pin is produced at the minimum tolerance (min-max tolerance) trace noise levels can occur. This level of noise does not affect the reliability or durability of the product. If piston-to-pin noise is detected and the customer desires the condition to be corrected, replace all six pistons with pin assemblies. The new piston sets have a minimal piston-to-pin clearance. Remember, piston-to-pin noise occurs in both park and drive at engine idle rpm and it varies in intensity depending on the number of pistons involved. A ticking sound means one piston is affected whereas a rattle or diesel type sound indicates more than one piston affected. The following should also be checked: 1. On W-Cars, make sure the right side engine splash shield is not contacting the engine crankshaft balancer. This condition usually happens cold and is caused by the shield curling when cold. 2. Reference Service Bulletin 57-71-06 for transmission rattle noise often confused for engine rattle noise. 3. Reference Service Bulletin 47-61-36 for Accessory Drive Belt Tensioner noise. 4. Check cylinder bore diameter and piston diameter as outlined in the Service Manual.
Filed Under (Toyota) by admin on 09-05-2011
Introduction Under certain operating conditions, the mounting area of the driver and/or front passenger sunvisor on the vehicle body may become damaged. If this has occurred, the sunvisor may become loose from the mounting area located on the headliner. To address this condition, newly designed mounting brackets have been made available to reinstall the sunvisors. Follow the procedures in this bulletin to install the mounting brackets. Repair Procedure 1. Remove the affected sunvisor assembly. Refer to the Technical Information System (TIS), applicable model year RAV4 Repair Manual: 2006 (to 01/2006) / 2006 (from 01/2006) / 2007 / 2008 / 2009 / 2010 RAV4: Vehicle Interior – Interior Panels/Trim – “Interior: Roof Headlining: Removal” 2. Straighten the roof sheet metal where the visor clips contact the roof. 3. Apply felt to the roof panel opening for visor as shown. Cut two strips from the felt sheet to the following dimensions: Length: 25 mm (1 in.) Width: 9 mm (3/8 in.) Thickness: 0.5 mm (0.02 in.) 4. Install the front visor support. NOTE Front and rear supports are identical. A. Thread string or thin wire through the opening of the support. B. Insert the support into the roof panel opening and attach the support hook to the front edge of the roof panel opening. NOTE • Hold the string or wire ends when installing to prevent the support from falling into the body. • Move the connector toward the rear of the vehicle to widen the opening. C. Attach felt between the support and the roof panel to hold the support in place. Cut two strips from the felt sheet to the following dimensions: Length: 25 mm (1 in.) Width: 5 mm (3/16 in.) Thickness: 0.5 mm (0.02 in.) D. Remove the string or wire from the support.
Filed Under (Toyota) by admin on 16-04-2010
Subject : Handling of DTC “P0420/P0430″ Case by Models This service bulletin is to inform you on how to handle “DTC P0420 / P0430″ cases for Yaris, Previa / Tarago, RAV4, Avensis Verso / Picnic. DESCRIPTION OF PHENOMENON • Engine MIL ON.
• Code P0420 or P0430 in the engine ECU. • No influence on driveability or engine performance.
PRODUCTION IMPROVEMENT Yaris: Modified Engine ECU software RAV4: Modified Engine ECU software and modified catalyst coating
Avensis Verso: Modified Engine ECU software and modified catalyst coating Previa: Modified Engine ECU software and modified catalyst coating