remove clutch pushrod from a 1988 ford f250 diesel


You are searching repair manual in PDF format about remove clutch pushrod from a 1988 ford f250 diesel use another keyword for search another post or files



  remove clutch pushrod from a 1988 ford f250 diesel Direct Download speed 5787 Kb/s

  remove clutch pushrod from a 1988 ford f250 diesel Full Version speed 6767 Kb/s




1988-90 Ford Super Duty HIGH CLUTCH EFFORT/ CLUTCH FLUID LEAK – CRACKED MOUNT

0

Filed Under (Ford) by admin on 26-01-2011

download
Incomplete clutch release and/or hydraulic fluid leaking into the cab from the clutch master cylinder may be caused by the reinforcement plate on the clutch master cylinder separating from the dash panel. The separation of the reinforcement plate reduces the clutch master cylinder pushrod travel. Reinforcement plate separation can also cause deflection of the clutch master cylinder that results in a misalignment of the pushrod to the clutch master cylinder. Misalignment causes the “O” ring in front of the secondary seal to leak hydraulic fluid. ACTION Inspect the truck and, if necessary, use the following service procedure to install a reinforcement kit. INSPECTION PROCEDURE 1. If the truck is a 1988 or later model, confirm that the starter interlock switch operates (the engine can be started) with the clutch pedal at least 0.5″ (12.7 mm) from the floor. 2. Test drive the truck and check for good clutch release. There should be no grinding of the gears, particularly when shifting from neutral to reverse gear. 3. If the truck passes these tests, go to the Small Reinforcement Installation Procedure Section of this article. 4. If either of the above conditions are not met, check the hydraulic system for air. Refer to the Suggested Bleeding Procedure at the end of this article. 5. Test drive the truck and check for improved clutch release. 6. If there is no improvement, proceed as follows: a. Remove the clutch master cylinder pushrod from the release lever pin on the release lever. b. Make sure the hole in the pushrod lines up with the pin, for those units requiring a minimal force

2005–2006 Toyota Tacoma CLUTCH PEDAL SQUEAK NOISE

0

Filed Under (Toyota) by admin on 04-06-2011

download
Some customers may complain about a “squeak” or “creak” noise when depressing or releasing the clutch pedal. The clutch master cylinder clevis assembly has been improved to eliminate this condition. Repair Procedure 1. Record all radio presets before starting. 2. Disconnect the negative (–) battery terminal cable. 3. Remove the clutch pedal sub–assembly. A. Remove the front door opening trim LH (scuff plate). B. Remove the cowl side trim board. C. Remove the instrument panel finish panel lower No. 1. D. Remove the driver’s side Junction Block. E. Remove the turnover (compression) spring. F. Remove the bolt attached to the instrument panel reinforcement assembly. G. Remove the clutch pedal sub–assembly. a. Remove the bolt and nut. b. Remove the clutch pedal from the clutch pedal support. 4. Remove the clutch pedal spring holder from the clutch pedal support. 5. Remove the clutch pedal pad. 6. Remove the two (2) clutch pedal bushes from the clutch pedal. 7. Remove the clutch pedal shaft collar. 8. Using needle–nose pliers, remove the No. 1 cushion from the clutch pedal. 9. Install the clutch pedal No. 1 cushion on the NEW clutch pedal sub–assembly. NOTE: Install parts on the NEW clutch pedal sub–assembly BEFORE installing in the vehicle. 10. Install the clutch pedal shaft collar. A. Apply MP grease to the clutch pedal shaft collar. B. Install the clutch pedal shaft collar onto the clutch pedal. 11. Install the clutch pedal bushes. A. Apply MP grease to the two (2) NEW bushes. B. Install the two (2) bushes onto the clutch pedal. 12. Install the clutch pedal pad. 13. Install the clutch pedal spring holder. A. Apply MP grease to the contact surface of the clutch pedal spring holder. B. Install the clutch pedal spring holder. 14. Remove the clevis sub–assembly. A. Measure length “A” of the clutch master cylinder. a. Measure length “A” between the lock nut and the thread end with a ruler. b. Record length “A”. B. Remove the clevis sub–assembly from the master cylinder. a. Loosen the lock nut. b. Rotate and remove the clevis sub–assembly. 15. Install the NEW clevis sub–assembly. A. Rotate the lock nut to match length “A”. B. Rotate and install the NEW clevis sub–assembly to contact the lock nut. C. Tighten the lock nut and torque to specification. Torque: 11.8 NSm (120 kgfScm, 8.7 ftSlbf) D. Apply MP grease to the ball end of the clevis sub–assembly where it will contact the clutch pedal. 16. Install the NEW clutch pedal sub–assembly. A. Install the clutch pedal onto the clutch support with the bolt and nut. Torque: 34 NSm (347 kgfScm, 25 ftSlbf) HINT: Install the bolt from the left side of the vehicle. B. Apply MP grease to the clutch pedal sub–assembly where the clevis sub–assembly contacts the clutch pedal. NOTE: Failure to apply grease to the clevis and clutch pedal sub–assemblies could cause the noise to return. C. Tighten the bolt to the instrument panel reinforcement assembly. Torque: 8 NSm (82 kgfScm, 6 ftSlbf) 17. Install the turnover (compression) spring. A. Apply MP grease to the contact surface of the spring holder, clutch pedal, and spring. B. Install the spring onto the clutch pedal and spring holder.

1993 Mitsubishi Montero TRANSFER CASE DISASSEMBLY

0

Filed Under (Mitsubishi) by admin on 30-12-2010

download
Disassembly (Ram-50) 1) Remove both 4WD indicator switches and steel balls. Remove speedometer gear assembly. Remove output shaft cover, gasket, wave spring and spacer. See Fig. 3. Remove rear cover, rear cover gasket and spacer from chain cover. Drive roll pin out of high-low shift fork. 2) Remove 2 seal plugs. Remove 2 poppet springs and steel balls. Shift transfer case to “4WD” and pull high-low shift rail out, in rear cover direction. Remove interlock plunger. Remove pulse generator (if equipped), front output shaft cover and pulse rotor (if equipped). Remove snap ring from rear bearing on output shaft. Remove chain cover, oil guide and side cover. Remove countershaft locking plate. Remove countershaft. 3) Remove countergear, 2 thrust washers, 2 needle bearings and spacer through side cover opening. Remove snap ring, spring retainers and spring from 2WD-4WD shift rail. Remove front output shaft, rear output shaft and chain as assembly. 4) Remove 2WD-4WD shift fork and distance piece. Drive out 2WD-4WD shift rail spring pin. Remove 2WD-4WD shift rail and lug. Remove high-low shift fork and high-low synchronizer sleeve. Remove needle bearing and snap ring from input gear. Remove input gear assembly. 5) If either control shaft or input gear oil seals are to be replaced, drive out roll pin from transmission control change shifter. Separate transfer case from adapter. See Fig. 3. Disassembly (Montero) 1) Remove dynamic damper, 5 detection switches and 3 steel balls. Remove poppet plug, spring and steel ball. Remove speedometer gear assembly. Remove output shaft rear cover, spacers, dust seal guard and oil seals. Front output shaft cover, wave spring and spacer (if equipped). 2) Remove high-low shift rail plug and high-low shift fork spring pin. Shift transfer case to “4WD”. Remove rear cover and high- low shift rail. Remove interlock plunger. Remove rear output shaft (viscous coupling) assembly and center differential assembly. Remove 2WD-4WD synchronizer assembly, chain and front output shaft from transmission as a unit. With White paint make match marks in grooves of 2WD-4WD synchronizer in 3 places. With White paint make match marks on spline projections of 2WD-4WD synchronizer sleeve in 3 places. Refer to match marks during reassembly. 3) Remove snap ring, spring seat, spring, 2WD-4WD shift fork and 2WD-4WD synchronizer sleeve. Remove differential lock hub, oil dam cover and bearing retainer. Remove side cover and gasket. Remove transfer counter gear shaft, transfer counter gear, thrust washer, needle bearings and spacer. Remove transfer drive shaft assembly. Remove high-low shift fork assembly and clutch sleeve. Remove transfer input gear assembly. 4) Remove 2WD-4WD shift lug spring pin, spring, spring retainer 2WD-4WD shift lug and shift rail. Remove input gear oil seal, baffle plate, dust seal guard and front output shaft oil seal. See Fig. 4.

1994 Ford Mustang A/C Evaporator Housing Removal and Installation

0

Filed Under (Ford) by admin on 06-03-2011

download
1. Disconnect battery ground cable (14301) . 2. Remove two console armrest mounting access covers (047A62) at rear of console panel (045A36) (snaps out) to gain access to armrest retaining bolts. 3. Remove four armrest-to-floor bracket retaining bolts and remove armrest assembly (snaps out of console). 4. Remove console panel gear shift plate (044G24) (snaps out). On vehicles equipped with manual transmissions, shift boot is attached to bottom of finish panel. Remove shift knob and slide boot and console panel gear shift plate up shift lever to remove. 5. To remove top finish panel position emergency brake lever in the UP position. Remove four retaining screws and lift top finish panel up. Disconnect necessary wire connectors. 6. Remove two console-to-rear floor bracket retaining screws. 7. Insert a small screwdriver into two notches at bottom of front upper finish panel and snap out. 8. If the vehicle has a radio chassis (18806) , the radio chassis must be removed. Refer to Section 15-01. If the vehicle doesn’t have a radio chassis , use a small screwdriver and pry radio cover finish panel out of console. 9. Flex glove compartment bin tabs inward. Drop down glove compartment (06010) assembly. Remove two console-to-instrument panel retaining screws. 10. Remove four console bracket retaining screws. Remove console panel from vehicle. 11. Remove three bolts retaining steering column opening cover (3A673) and reinforcement panel. Remove cover. 12. Remove steering column opening reinforcement by removing two bolts. 13. Remove two bolts retaining steering column opening reinforcement and remove reinforcement. 14. Remove six steering column retaining nuts (two retaining the hood release mechanism and four retaining column to lower brake pedal support). Lower steering column to floor. 15. Remove upper and lower steering column shrouds (3530) and disconnect wiring from turn signal and windshield wiper switch (13K359) . 16. Remove steering column through bolt and nut on engine compartment side of cowl panel. Remove steering column from vehicle. 17. Remove brake pedal support nut. 18. Snap out instrument panel defroster opening grille (044E82) . 19. Remove screws from speaker covers. Snap out speaker covers. 20. Remove front screws retaining RH and LH scuff plates at cowl side trim panels. 21. Remove RH and LH cowl side trim panels. 22. Disconnect wiring at RH cowl side. 23. Remove cowl side retaining bolts (one each side). 24. Remove five cowl top screws attachments. 25. Gently pull instrument panel (04320) away from RH side of cowl panel. Disconnect speedometer cable, air conditioning controls and wire connectors. 26. Place a drain pan or suitable container under the heater water hose connections at the cowl panel. 27. Disconnect heater water hoses (18472) from heater core tubes and plug heater water hoses with suitable 5/8-inch and 3/4-inch plugs. Cap heater core tubes to prevent coolant loss from heater core (18476) during removal of heater case. 28. Remove screw retaining A/C evaporator case support bracket (19A639) to cowl top panel. 29. Disconnect vacuum supply supply hose (black) from A/C vacuum supply in engine compartment. 30. Working under the hood (16612) , remove nut retaining heater case to cowl panel. 31. Inside passenger compartment, remove screw retaining A/C evaporator case mounting bracket (19A865) to cowl top panel. 32. Remove one screw retaining A/C evaporator case mounting bracket below heater case to cowl panel. 33. Carefully pull heater case from cowl panel and remove heater case assembly from vehicle. 34. To install, reverse Removal procedure. Check operation of all components. 35. After repairs have been completed, check the coolant level in the radiator (8005) and in the radiator coolant recovery reservoir (8A080) . Fill as required with the recommended coolant mixture.

2000 Ford F-Super Duty 250-550 Clutch Master Cylinder and Reservoir REMOVAL AND INSTALLATION

0

Filed Under (Ford) by admin on 08-03-2011

download
Removal CAUTION: Remove the entire clutch hydraulic system from the vehicle as an assembly when installing a new clutch master cylinder assembly (7C522). 1. Disconnect the clutch hydraulic tube from the dash clip. 2. Raise and support the vehicle. For additional information, refer to Section 100-02. 3. Unlock and remove the slave cylinder (7A564) from the transmission. Compress and twist the slave cylinder to unlock it from the transmission. 4. Disconnect the clutch hydraulic tube from the floor pan clip. Position the slave cylinder and hydraulic tube forward below the left engine bank. This will make it easier to unlock the clutch master cylinder from the clutch pedal and support bracket (7B633) by reducing tension on the hydraulic tube. 5. Lower the vehicle. 6. WARNING: The clutch pedal is under spring tension. Unlock the push rod bushing retaining clips and separate the clutch master cylinder push rod from the clutch pedal. 7. Remove and discard the push rod bushing (7526). 8. Remove the switch cover, and remove the clutch pedal position switch (7C534) from the clutch master cylinder push rod. 9. Separate the power distribution box from the bracket to gain access to the clutch master cylinder. 10. Unlock and remove the clutch master cylinder from the clutch pedal and support bracket. Compress and twist the clutch master cylinder clockwise 45 degrees to unlock it from the clutch pedal and support bracket. 11. Remove the clutch hydraulic reservoir from the wiring tray and separate the clutch hydraulic tube from the brake master cylinder assembly. Position the clutch hydraulic reservoir aside. 12. CAUTION: Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, wash the surface with water immediately. Remove the clutch hydraulic system from the vehicle. 13. Clean the clutch hydraulic system components to prevent contaminants from entering the hydraulic system. 14. CAUTION: Place a suitable container under the clutch master cylinder. Disconnect the hydraulic tube from the clutch master cylinder. 1. Using a 3/32-inch punch and a hammer, drive out the roll pin, and discard it. 2. Disconnect the hydraulic tube from the clutch master cylinder.