remove wiper motor 1988 pajero


You are searching repair manual in PDF format about remove wiper motor 1988 pajero use another keyword for search another post or files



  remove wiper motor 1988 pajero Direct Download speed 5787 Kb/s

  remove wiper motor 1988 pajero Full Version speed 6767 Kb/s




2007 Buick Terraza Rear Window Wiper Motor Replacement

0

Filed Under (Buick) by admin on 18-11-2010

download
1. Remove the rear wiper arm (5). 2. Remove the rear wiper motor drive shaft nut (6). 3. Remove the washer (7) and seal (8) from the wiper motor drive shaft. 4. 5. 6. 7. 8. Remove the liftgate trim panel. Disconnect the electrical connector (1) from the rear wiper motor. Remove the rear wiper motor screws. Remove the rear wiper motor (3) from the liftgate (5). Remove the rear wiper motor from the vehicle. Installation Procedure 1. Position the rear wiper motor (3) to the liftgate. Notice: refer to Fastener Notice. 2. Install the rear wiper motor screws. Tighten the screws to 6 N.m (53 lb in ). 3. Connect the electrical connector (1) to the wiper motor. 4. Install the washer (7) and seal (8) onto the rear wiper motor drive shaft. 5. Install the rear wiper motor drive shaft nut (6). Tighten the nut to 6 N.m (53 lb in ). 6. Install the rear wiper arm. 7. Inspect rear wiper for proper operation. 8. Install the liftgate trim panel.

Related entry:

2001 avalon windshield wiper transmission exploded diagram, where is windshield washer fuse peugeot 307, remove and replace rear wiper motor on terraza, rear motor mount replacement on toyota sienna, 2006 honda odyssey rear wiper motor removal, removing lexus rx 350 rear wiper arm, 2003 avalanche wiper motor cover, windshield wiper motor wiring diagram 2003 dodge grand caravan sport, how to replace rear wiper arm on 2011 equinox 2 4, remove toyota matrix rear window waper moter,

1993 Mitsubishi Montero TRANSFER CASE DISASSEMBLY

0

Filed Under (Mitsubishi) by admin on 30-12-2010

download
Disassembly (Ram-50) 1) Remove both 4WD indicator switches and steel balls. Remove speedometer gear assembly. Remove output shaft cover, gasket, wave spring and spacer. See Fig. 3. Remove rear cover, rear cover gasket and spacer from chain cover. Drive roll pin out of high-low shift fork. 2) Remove 2 seal plugs. Remove 2 poppet springs and steel balls. Shift transfer case to “4WD” and pull high-low shift rail out, in rear cover direction. Remove interlock plunger. Remove pulse generator (if equipped), front output shaft cover and pulse rotor (if equipped). Remove snap ring from rear bearing on output shaft. Remove chain cover, oil guide and side cover. Remove countershaft locking plate. Remove countershaft. 3) Remove countergear, 2 thrust washers, 2 needle bearings and spacer through side cover opening. Remove snap ring, spring retainers and spring from 2WD-4WD shift rail. Remove front output shaft, rear output shaft and chain as assembly. 4) Remove 2WD-4WD shift fork and distance piece. Drive out 2WD-4WD shift rail spring pin. Remove 2WD-4WD shift rail and lug. Remove high-low shift fork and high-low synchronizer sleeve. Remove needle bearing and snap ring from input gear. Remove input gear assembly. 5) If either control shaft or input gear oil seals are to be replaced, drive out roll pin from transmission control change shifter. Separate transfer case from adapter. See Fig. 3. Disassembly (Montero) 1) Remove dynamic damper, 5 detection switches and 3 steel balls. Remove poppet plug, spring and steel ball. Remove speedometer gear assembly. Remove output shaft rear cover, spacers, dust seal guard and oil seals. Front output shaft cover, wave spring and spacer (if equipped). 2) Remove high-low shift rail plug and high-low shift fork spring pin. Shift transfer case to “4WD”. Remove rear cover and high- low shift rail. Remove interlock plunger. Remove rear output shaft (viscous coupling) assembly and center differential assembly. Remove 2WD-4WD synchronizer assembly, chain and front output shaft from transmission as a unit. With White paint make match marks in grooves of 2WD-4WD synchronizer in 3 places. With White paint make match marks on spline projections of 2WD-4WD synchronizer sleeve in 3 places. Refer to match marks during reassembly. 3) Remove snap ring, spring seat, spring, 2WD-4WD shift fork and 2WD-4WD synchronizer sleeve. Remove differential lock hub, oil dam cover and bearing retainer. Remove side cover and gasket. Remove transfer counter gear shaft, transfer counter gear, thrust washer, needle bearings and spacer. Remove transfer drive shaft assembly. Remove high-low shift fork assembly and clutch sleeve. Remove transfer input gear assembly. 4) Remove 2WD-4WD shift lug spring pin, spring, spring retainer 2WD-4WD shift lug and shift rail. Remove input gear oil seal, baffle plate, dust seal guard and front output shaft oil seal. See Fig. 4.

Related entry:

how to remove 2000 continental radiator, how to remove pagero front LHS drive shaft, remove front bumper es 300 lexus 2003, challenger fron cowl removal, how to remove gear shift knob on 2005 pacifica, buick enclave gear shift concole removal, how to remove fuel injectors in nissan cabover UD, how to replace cv joint shafts on 2000 mitsubishi Galant, remove rear shocks on ford 500, How to pull out rear windows in a fj40,

2001 Toyota Sienna CE Trunk / Liftgate Service and Repair DISASSEMBLY

0

Filed Under (Toyota) by admin on 11-07-2010

download
1. REMOVE BACK DOOR ASSIST GRIP a. Using a screwdriver, open the covers. HINT: Tape the screwdriver tip before use. b. Remove the 2 screws and assist grip. 2. REMOVE BACK DOOR PULL STRAP a. Using a screwdriver, remove the strap cover. HINT: Tape the screwdriver tip 3. REMOVE CENTER GARNISH Using a screwdriver, remove the center garnish. HINT: Tape the screwdriver tip before use. 4. REMOVE SIDE GARNISH a. Using a screwdriver, remove the side garnish. HINT: Tape the screwdriver tip before use. b. Employ the same manner described above to the other side. 5. REMOVE DOOR TRIM BOARD a. Insert a screwdriver between the door and door trim board to pry the door trim board out. NOTE: Be careful not to damage the door and door trim board. HINT: Tape the screwdriver tip before use. b. Pull the door trim board to remove it. 6. REMOVE HIGH-MOUNTED STOP LIGHT a. Remove the 2 screws. b. Disconnect the connector. c. Remove the high-mounted stop light. 7. REMOVE WASHER NOZZLE 8. REMOVE REAR WIPER ARM Remove the nut, rear wiper arm. Torque: 5.4 N.m (55 kgf.cm, 48 in.lbf) 9. REMOVE WIPER MOTOR AND LINK ASSEMBLY a. Remove the 3 bolts from the wiper motor. b. Remove the 2 bolts and wiper motor and link assembly. Torque: 5.4 N.m (55 kgf.cm, 48 in.lbf) c. Remove the grommet. 10. REMOVE COMBINATION LIGHTS 11. REMOVE LICENSE PLATE LIGHT ASSEMBLY a. Disconnect the back door control cable from the handle lever. b. Disconnect the connector. c. Remove the 3 nuts. d. Using a screwdriver, remove the license plate light assembly. HINT: Tape the screwdriver tip before use. e. Remove the handle lever from the license plate light cover. f. Remove the license plate light assembly from the license plate light cover. 12. REMOVE KEY CYLINDER

Related entry:

2005 sienna center console removal, 200 sienna dash light replacement, remove heater/ac panel toyota sienna, remove dent from sienna lift gate, lincoln mkx passenger rear sidemarker light attachment, idler pulley sienna 2007, how yo change out a servo sub-assembly damper in a toyota avalon, how to replacement crankshafts sealy from toyota sienna 2001 minivan, how to replace brake light switch 2005 avalanche, how to change crank pulley on 2004 toyota sienna,

1994 Ford Mustang A/C Evaporator Housing Removal and Installation

0

Filed Under (Ford) by admin on 06-03-2011

download
1. Disconnect battery ground cable (14301) . 2. Remove two console armrest mounting access covers (047A62) at rear of console panel (045A36) (snaps out) to gain access to armrest retaining bolts. 3. Remove four armrest-to-floor bracket retaining bolts and remove armrest assembly (snaps out of console). 4. Remove console panel gear shift plate (044G24) (snaps out). On vehicles equipped with manual transmissions, shift boot is attached to bottom of finish panel. Remove shift knob and slide boot and console panel gear shift plate up shift lever to remove. 5. To remove top finish panel position emergency brake lever in the UP position. Remove four retaining screws and lift top finish panel up. Disconnect necessary wire connectors. 6. Remove two console-to-rear floor bracket retaining screws. 7. Insert a small screwdriver into two notches at bottom of front upper finish panel and snap out. 8. If the vehicle has a radio chassis (18806) , the radio chassis must be removed. Refer to Section 15-01. If the vehicle doesn’t have a radio chassis , use a small screwdriver and pry radio cover finish panel out of console. 9. Flex glove compartment bin tabs inward. Drop down glove compartment (06010) assembly. Remove two console-to-instrument panel retaining screws. 10. Remove four console bracket retaining screws. Remove console panel from vehicle. 11. Remove three bolts retaining steering column opening cover (3A673) and reinforcement panel. Remove cover. 12. Remove steering column opening reinforcement by removing two bolts. 13. Remove two bolts retaining steering column opening reinforcement and remove reinforcement. 14. Remove six steering column retaining nuts (two retaining the hood release mechanism and four retaining column to lower brake pedal support). Lower steering column to floor. 15. Remove upper and lower steering column shrouds (3530) and disconnect wiring from turn signal and windshield wiper switch (13K359) . 16. Remove steering column through bolt and nut on engine compartment side of cowl panel. Remove steering column from vehicle. 17. Remove brake pedal support nut. 18. Snap out instrument panel defroster opening grille (044E82) . 19. Remove screws from speaker covers. Snap out speaker covers. 20. Remove front screws retaining RH and LH scuff plates at cowl side trim panels. 21. Remove RH and LH cowl side trim panels. 22. Disconnect wiring at RH cowl side. 23. Remove cowl side retaining bolts (one each side). 24. Remove five cowl top screws attachments. 25. Gently pull instrument panel (04320) away from RH side of cowl panel. Disconnect speedometer cable, air conditioning controls and wire connectors. 26. Place a drain pan or suitable container under the heater water hose connections at the cowl panel. 27. Disconnect heater water hoses (18472) from heater core tubes and plug heater water hoses with suitable 5/8-inch and 3/4-inch plugs. Cap heater core tubes to prevent coolant loss from heater core (18476) during removal of heater case. 28. Remove screw retaining A/C evaporator case support bracket (19A639) to cowl top panel. 29. Disconnect vacuum supply supply hose (black) from A/C vacuum supply in engine compartment. 30. Working under the hood (16612) , remove nut retaining heater case to cowl panel. 31. Inside passenger compartment, remove screw retaining A/C evaporator case mounting bracket (19A865) to cowl top panel. 32. Remove one screw retaining A/C evaporator case mounting bracket below heater case to cowl panel. 33. Carefully pull heater case from cowl panel and remove heater case assembly from vehicle. 34. To install, reverse Removal procedure. Check operation of all components. 35. After repairs have been completed, check the coolant level in the radiator (8005) and in the radiator coolant recovery reservoir (8A080) . Fill as required with the recommended coolant mixture.

Related entry:

2003 mustang console removal, removel heat duck in front center console 1999 cavalier, remove heater panel 2008 honda pilot, how to change an ac compressor in a 2006 e450, 2004 e250 fan switch, how to remove the middle gear shift console in a chrysler sebring 2007 touring, removing gear shifter trim on 2003 kia sorento, how to remove center console 2002 rav4, how to remove center console 1998 blazer s10, 2009 tahoe console ebony,

1994 Suzuki Swift WIPER/ WASHER SYSTEM

0

Filed Under (Suzuki) by admin on 15-06-2010

download
A 2-speed wiper motor with intermittent mode is standard on all models. A 3-speed wiper motor is optional on some models. Washer system uses a reservoir-mounted electric pump located in the engine compartment. A one-speed rear wiper/washer is optional. Rear wiper/washer switch is located on instrument panel, to right of steering column. Wiper switch has 2 positions, rear wiper ON or OFF. Washer and wiper switch has 3 positions, OFF, washer ON (depressed half way), or washer and wiper ON (fully depressed). Washer/wiper switch moves to OFF position when switch is released. TESTING NOTE: If wiper malfunctions or does not return to park position,check for blown fuse, faulty wiper motor, control switch or connections. If washer malfunctions, check for clogged hose or nozzle, faulty washer motor, control switch or wiring. FRONT WIPER MOTOR REAR WIPER MOTOR INTERMITTENT WIPER RELAY WIPER/WASHER SWITCH WIPER MOTOR BRUSH & COMMUTATOR REMOVAL & INSTALLATION WIPER MOTOR WIRING DIAGRAMS

Related entry:

1976 gmc truck wiper switch wiring, 2000 ford expedition washer nozzle l shape coupler, faulty wiper switch on a 2006 l200 how do yo bypass switch so wipers work, how to remove a wiper switch from a 1994ford tempo, removing window switch 1998 saturn,